The existing clock synchronization code has two flaws: intermittent
transmission latency during get_status requests can cause the
estimated clock to be too low, and the estimated clock calculation did
not take into account possible clock drift between samples. The
former could potentially lead to "Timer too close" errors and the
latter could potentially lead to "Move queue empty" errors.
Rework the code to avoid the above problems. It's not necessary to
estimate the micro-controller clock as an excellent estimate is
reported by the micro-controller (via the CLOCK_FREQ constant).
Account for a small drift from the reported value, and check on each
sample if the drift exceeds the expected limits. With a good starting
estimated clock, only the offset needs to be calculated. Use previous
offsets (and the estimated clock) in calculation of new offsets to
avoid intermittent latency from badly skewing the results. Finally,
add an additional time offset of one millisecond to account for any
minor inaccuracies.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the command dispatch and response generation so that most of
the work is done on pru0 instead of pru1. This allows more code to
fit into the limited space on pru1.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't use the sendf() macro for ack and nak messages - directly call
the command_sendf() code instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that console_get_input(), console_pop_input(),
console_get_output() and console_push_output() are local functions,
integrate them into their callers. This simplifies the code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that console_get_input(), console_pop_input(),
console_get_output() and console_push_output() are local functions,
integrate them into their callers. This simplifies the code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that console_get_input(), console_pop_input(),
console_get_output() and console_push_output() are local functions,
integrate them into their callers. This simplifies the code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Export a new console_sendf() function from the board code instead of
console_get_output() and console_push_output(). This enables more
flexibility in how the board specific code produces output.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the command_task() code from the generic code to the board
specific code. This enables more flexibility in how the board
specific code processes input.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the code so that message block framing, command parsing, and
command dispatch are distinct.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some systems point python to python3 instead of python2 - explicitly
request python2 to avoid conflicts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure the heater.target_temp is set during the auto-tune test so
that the heater.set_pwm() command will allow the heater to be turned
on.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add python-virtualdev to the list of system packages to be installed -
it's usually already installed, but it doesn't hurt to add it to the
list in case it isn't already installed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The endstop_position is intended to support different values for each
stepper so that the individual tower heights can be configured.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit d0932009 introduced an error that could cause lost input in
cases where the sender did not wait for an "ok" message before sending
the next command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't modify dictionaries while iterating them and be careful to use
// when doing an integer divide.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create add_printer_objects() functions in the fan, heater, extruder,
and toolhead modules. Create the necessary printer component objects
from this call instead of placing the code directly in klippy.py.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It appears this option is commonly needed on the at90usb1286 avr chip
(the printrboard requires it), so default it on.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a CONFIG_SIMULAVR option to the Kbuild menus and don't directly
prompt users for CONFIG_WATCHDOG or CONFIG_SERIAL_BAUD_U2X. The only
reason to disable these options would be if one were running on
simulavr. This simplifies the user visible menu options.
Also, only show CONFIG_CLEAR_PRESCALER for at90usb1286 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega328 is basically the same as the atmega168 - it just adds
some additional memory. Allow the chip to be selected during the
build.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor