Kevin O'Connor
7b170d8c3d
github: Automatically close resolved issues after one week of inactivity
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-13 22:55:43 -04:00
Matthew Lloyd
49937f6281
config: Enable PID for bed heater in printer-fokoos-odin5-f3-2021.cfg ( #4288 )
...
Signed-off-by: Matthew Lloyd <github@matthewlloyd.net>
2021-05-13 22:33:00 -04:00
Kevin O'Connor
b4a2229788
config: Minor changes to printer-fokoos-odin5-f3-2021.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-12 15:01:23 -04:00
Matthew Lloyd
93add3a095
config: Add printer-fokoos-odin5-f3.cfg ( #4286 )
...
Signed-off-by: Matthew Lloyd <github@matthewlloyd.net>
2021-05-12 15:00:06 -04:00
Kevin O'Connor
4799d05d42
config: Add generic-ruramps-v1.3.cfg to test cases and minor updates
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-12 10:25:41 -04:00
Marco Robustini
831a4fe7fa
config: Configuration file for RuRamps V1.3 boards ( #4279 )
...
Signed-off-by: Marco Robustini <robustinimarco@gmail.com>
2021-05-12 10:19:25 -04:00
Pranas Kiziela
b4b2afca3b
config: Fix rotation_distance for Sapphire Plus
...
Signed-off-by: Pranas Kiziela <pranas.kiziela@gmail.com>
2021-05-12 10:00:55 -04:00
Alex Zellner
60352f4b67
filament_motion_sensor: add get_status ( #4281 )
...
Signed-off-by: Alex Zellner <alexander.zellner@googlemail.com>
2021-05-11 13:17:22 -04:00
Arksine
dc71b64c0a
virtual_sdcard: fix check for case sensitive files
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2021-05-11 13:15:56 -04:00
Kevin O'Connor
8eef1e2146
config: Use "stealthchop_threshold: 999999" if set
...
Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-09 09:02:43 -04:00
Kevin O'Connor
1ed67120cd
debugcmds: Remove start/end_group commands
...
These commands were never used by the main code and are not
particularly helpful for debugging. Remove them to reduce code size -
in particular on the pru architecture.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-07 13:53:47 -04:00
Kevin O'Connor
76b839a0ac
invalid-label-bot: Minor changes to invalid label comment
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-06 14:29:31 -04:00
Kevin O'Connor
bde6215c3f
stm32: Enable ADC3 pins on stm32f446
...
Reported by @bigtreetech.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-06 12:43:13 -04:00
Dany Yanev
b333547f1f
menu: Fixed typo when reading `print_stats.state` ( #4261 )
...
Fixed typo when reading `print_stats.state` causing some of the menus to now show up.
Signed-off-by: Dany Yanev <yanev89@gmail.com>
2021-05-06 11:54:27 -04:00
Kevin O'Connor
7bf379d75d
docs: Fix typo in Config_Reference.md
...
Should be "hybrid-corexy" instead of "hybrid-codexy". Reported by
@mak0t0san.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-06 11:46:35 -04:00
Kevin O'Connor
c9e8298c36
config: Minor updates to printer-velleman-k8800-2017.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-06 11:38:31 -04:00
Jelle Victoor
71f4739c8b
config: Feature/add k8800 config ( #4212 )
...
Signed-off-by: Jelle Victoor <victoor.jelle@gmail.com>
2021-05-06 11:31:45 -04:00
Kevin O'Connor
dfcdd51e7f
config: Minor changes to printer-creality-cr30-2021.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-06 11:08:57 -04:00
Jason S. McMullan
44387568f3
config: Add Creality CR-30 PrintMill support
...
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
2021-05-06 11:07:18 -04:00
Kevin O'Connor
45cd3543e3
lpc176x: Use full peripheral clock speed; fix UART interface
...
Commit ae89a659
caused a regression in the lpc176x UART handling.
After that commit the UART clock divisor would need to be 6.25 on
lpc1768 or 7.5 on lpc1769, but the code only supports whole numbers.
Set the PCLKSELx registers at startup and return to using full speed
peripheral clocks.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-04 20:29:48 -04:00
Wilhelm Schuster
5fb5b3afe1
spi_flash: Add board definitions for Fysetc S6 and Spider
...
Signed-off-by: Wilhelm Schuster <ws@rot13.io>
2021-05-03 14:36:18 -04:00
Wilhelm Schuster
4ae307b10f
config: Update Fysetc S6 compilation instructions
...
Signed-off-by: Wilhelm Schuster <ws@rot13.io>
2021-05-03 14:36:18 -04:00
Wilhelm Schuster
1fb091c4fa
stm32: Allow selecting bootloader size for STM32F446
...
Signed-off-by: Wilhelm Schuster <ws@rot13.io>
2021-05-03 14:36:18 -04:00
Tircown
f2c74ec023
kinematics: Add hybrid-corexy and hybrid-corexz ( #4229 )
...
Signed-off-by: Fabrice GALLET <tircown@gmail.com>
2021-05-03 14:31:23 -04:00
Kevin O'Connor
f10247a498
gcode_macro: Deprecate default_parameter_<name>
...
The Jinja2 "set" directive is more flexible and easier to understand
than default_parameter_XXX parameters. Deprecate it and encourage
using "set" as a replacement.
This also deprecates direct access to parameters via parameter name in
a macro. Going forward, the `params` pseudo-variable must be used to
access a parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-03 12:43:53 -04:00
Kevin O'Connor
dd28c7aef7
config: Fix whitespace error in generic-fysetc-spider.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-03 12:40:11 -04:00
George Fu
fee386b8e2
config: add example configs for fysetc spider board
...
Signed-off-by: George Fu <nailao_5918@163.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-03 12:01:00 -04:00
Kevin O'Connor
5ceb5a1b26
invalid-label-bot: Fix typo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-03 11:06:09 -04:00
Kevin O'Connor
f2b382dbcc
invalid-label-bot: Reword the invalid label message
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-02 18:51:08 -04:00
Kevin O'Connor
89082b494f
klippy: Report known software versions on a protocol error during connection
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-05-02 17:51:15 -04:00
shiftingtech
8443c0b0f8
docs: a slight clarity improvement for the rPi mcu
...
Just a small attempt to make the build process slightly clearer
In the compilation instructions for the rPi mcu
Signed-off-by: Ben Eastep <shifting@shifting.ca>
2021-05-02 13:07:07 -04:00
Kevin O'Connor
edea52863a
endstop: Report trigger time in endstop_query response
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:40:37 -04:00
Kevin O'Connor
470b1e2e46
adxl345: Use "clock" suffix instead of "time" in commands
...
The debugging code knows how to handle fields that end in "clock".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:40:37 -04:00
Kevin O'Connor
b611e72a19
pulse_counter: Use "clock" suffix instead of "time" in commands
...
The debugging code knows how to handle fields that end in "clock".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:40:37 -04:00
Kevin O'Connor
8f76e53c0e
stepper: Remove min_stop_interval from mcu code
...
Now that the host never uses a min_stop_interval, remove it from the
mcu code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:26:19 -04:00
Kevin O'Connor
b1ea4f3bef
toolhead: Do not limit SET_VELOCITY_LIMIT to values specified in config
...
Allow a larger velocity, accel, and square_corner_velocity than what
is specified in the config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:26:19 -04:00
Kevin O'Connor
5a5ecd88e2
stepper: Do not set min_stop_interval in micro-controller
...
The min_stop_interval safety check is fragile and leads to a notable
amount of complexity. Avoid these issues by not programming this
safety check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-30 11:09:08 -04:00
Kevin O'Connor
d1946fb6ed
graphstats: Support graphing multiple heaters
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-29 15:53:28 -04:00
Kevin O'Connor
0a4a64058d
probe: Use original XY position on multiple probe samples
...
On some kinematics it's possible for the XY position to change
slightly during a probing move. Return back to the original XY
position on a probe lift so each probe attempt starts at the same
nominal position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 21:40:49 -04:00
Kevin O'Connor
0990a3da6f
gcode: Generate M115 output even if command not sent from gcode pseudo-terminal
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 21:40:03 -04:00
Kevin O'Connor
25389027de
Revert "endstop_phase: wip"
...
This reverts commit f2e4653ca4
.
Revert incomplete testing code that was accidentally committed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 20:42:33 -04:00
Kevin O'Connor
e77bf7431e
docs: Move palette2 location in Config_Reference.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 20:40:24 -04:00
Kevin O'Connor
ebbb21be00
docs: Update Status_Reference.md for better Jekyll rendering
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 20:38:07 -04:00
Kevin O'Connor
f2e4653ca4
endstop_phase: wip
2021-04-28 20:32:14 -04:00
Kevin O'Connor
af7f27542f
docs: Move status field reference to new Status_Reference.md file
...
Move the reference of "printer" status fields from
Command_Templates.md to a new Status_Reference.md file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-28 20:32:00 -04:00
Dmitry Butyugin
3b33d6652f
resonance_tester: Refactored the testing code
...
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
2021-04-28 12:36:23 -04:00
Johannes Stuettgen
ed6ab6b9cc
screws_tilt_adjust: Add MAX_DEVIATION parameter for bed level invariant.
...
This is useful when a saved bed mesh is used to ensure that the bed level
has not drifted too far from where it was when the mesh was created.
Signed-off-by: Johannes Stuettgen <johannes.stuettgen@gmail.com>
2021-04-28 11:53:18 -04:00
Kevin O'Connor
d36dbfebd1
docs: Prefer Jinja2 "set" directive to default_parameter_xxx in examples
...
The "set" directive is more flexible and easier to understand.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-26 12:44:51 -04:00
Kevin O'Connor
61a25d2fb2
docs: Add example of Jinja2 "set" directive to Command_Templates.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-26 12:44:21 -04:00
Kevin O'Connor
475d8a72ad
docs: Add notes on terminating resistors to CANBUS.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2021-04-25 15:45:24 -04:00