This PR is to remove `move_to_previous: true` from the ender 3 S1 and S1 plus configs. This is a confusing option, it is not really useful on these type of printers and can cause issue to the end user
Signed_off_by; James Hartley <james@hartleyns.com>
The header documentation currently shows the year the Creality Ender 3 V2 Neo as being the 2020 model. This is likely a copy/paste error from the header of the original Creality Ender 3 V2 config. The year the Creality Ender 3 V2 Neo came out was in 2022 as indicated by the name of this config file. This patch fixes the copy/paste typo by updating the year in the header documentation from 2020 to 2022.
Signed-off-by: Jason W. Thompson <jason@jasonthompson.dev>
New printer : Longer LK4X configuration
This configuration is based on the one provided by Longer with some tweaks.
Signed-off-by: Thomas Lété <bistory@gmail.com>
As found on the discord by user Qtin, this board now ships with one of STM32H743 or STM32H723
Example config updated to reflect this. This has been tested on the users board. To note, the H743
bin will flash to the H723 chip, but will not work.
Signed-off-by: James Hartley <james@hartleyns.com>
This adds support for the stock configuration of the V-Minion printer from Ratrig, based on the Octopus v1.1 (STM32F446)
Signed-off-by: Benjamin Lesher <bbro44@protonmail.com>
Having the controller fan PA14 in the config is important for the stepper drivers not to overheat and skip steps.
Signed-off-by: Robert Lilienthal <13837429+RobLil@users.noreply.github.com>
Add the default base config for the Ender 3 v2 Neo (as released 2022).
This config also works with the newer D32F303 based 4.2.2 boards.
Signed-off-by: Sam McLeod <sammcj@users.noreply.github.com>
Fix filament sensor and remove unneeded config changes in extruder
The filament sensor on the printer used for initial testing had been removed prior to flashing klipper to it. Only a basic test to see it if triggered or not was preformed. It was discovered by someone else doing some testing on another printer that it would frequently pause. This was a simple oversight, assuming it was a runout switch.
Removed section of config related to filament runout switch and replaced with basic config for filament motion so they printer will simply pause when no more motion is detected. Also notated to add CLEAR_PAUSE to start gcode if using this sensor as it will trigger a paused state when loading or unloading filament. If printer is in a paused state at the start of the print, the attempt to pause will cause the printer to rapidly pause and unpause itself.
Removed min_extruder_temp and max_extrude_only_distance from the extruder section, as they were there only for macros on a test system that is not put into this sample config
Signed-off-by: Zachary Welvaert <zwelvaert@gmail.com>
The actual board name is EZBoard V2 without the lite. Renaming the file and correcting the intro text to reflect the actual board name.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
Config file contains pin mappings to suit Lulzbot Mini 2 using Lulzbot SingleExtruder(0.5mm) and Lulzbot flexible magnetic bed.
Mini 2 uses Einsy Retro mainboard.
Signed-off-by: Trent Sheather <trent.sheather@gmail.com>
Minor fix. The screw labels "back left" and "back right"
where swapped in [screws_tilt_adjust] section.
Signed-off-by: Frank Roth <developer@freakydu.de>
Works for unmodified stock Artillery Sidewinder X2,
year 2022 with Artillery Ruby v1.2 mainboard.
All by default connected things are working fine.
Build firmware with architecture STM32F401 with "No bootloader".
Other settings keep ther defaults
Signed-off-by: Frank Roth <developer@freakydu.de>
Corrected the build instructions for the TH3D EZBoard V2 to include the command to convert Klipper.elf to a SREC bin format named firmware.bin. The SREC format is required for the bootloader installed on the board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
* Update printer-anycubic-vyper-2021.cfg
better pause and end print, beeper support, mroe accurate value.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
delete unnecessary gcode
* Update printer-anycubic-vyper-2021.cfg
remove unneccessary part.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
according to https://www.klipper3d.org/Example_Configs.html point 7f
delete field values that are set to their default value
* Update printer-anycubic-vyper-2021.cfg
small change
* Update printer-anycubic-vyper-2021.cfg
As found on discord bt user David Carey.
uart_address for y and z are swapped. Discovered while setting up sensorless homing.
Signed off by: James Hartley <james@hartleyns.com>
Added a SET_DIGIPOT command to the mcp4018 implementation.
Previously the mcp4018 was read only, and set at the time of
configuration. This allows you to change the value during a
print, which is needed for some older printers that need to
lower the stepper current during preheating.
Signed-off-by: Jake Bordens <jake@allaboutjake.com>
This is a working config with full LCD and stepper settings (only thing missing is the kill switch, which did not appear to work)
Signed-off-by: Rui Carmo <rui.carmo@gmail.com>
JamesH1978