Implements AxisTwistCompensation, and Calibrater
Supports calibration of z-offsets caused by x gantry twist
Modify PrinterProbe._probe function to check if the probed z value should be adjusted
based on axis_twist_compensation's configuration
Add documentation for [axis_twist_compensation] module
Signed-off-by: Jeremy Tan <jeremytkw98@gmail.com>
COPY and MIRROR mode implementation
Correctly apply input shaper params to new dual_carriage
Added SAVE_/RESTORE_IDEX_STATE commands
Documentation updates for the new IDEX modes
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
I am endeavoring to rewrite some of the docs to be more front end agnostic to reflect the different front ends available since these docs were written. I am starting with this one, as it quite often used.
Signed-off-by: James Hartley <james@hartleyns.com>
The reference to my_nozzle_fan is misleading and could cause people to skip over the [fan] definition and assume this is the parts/print cooling fan. Alias changed to reflect heatbreak_cooling_fan as used in most configs that have a controllable hotend fan.
Signed-off-by: James Hartley <james@hartleyns.com>
Clarifying the ADXL345 on pi instructions. Previously, the instructions on installing the linux klipper instance were in a confusing place.
Signed-off-by: Adam Kramer <akramer@gmail.com>
Change the default CANbus frequency from 500000 to 1000000. A higher
frequency allows for greater data transfer rates, lower latency of
messages, and should overall be more robust.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Recommend USB to CAN adapter and no longer recommend using the
waveshare rpi hat.
Recommend using allow-hotplug for all USB adapters.
Note bandwidth limitations when using USB to CAN bridge mode.
Note that a USB to CAN mcu is not a USB serial device.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The control bytes for the AHT20 and AHT21 are identical to the AHT10, but I had not been able to test just yet to ensure the sensor code supported the other sensors. I've wrapped up testing and updated the comments/docs to reflect this additional support.
Signed-off-by: Scott Mudge <mail@scottmudge.com>
Correction for table "Recommended connection scheme for I2C (i2c0a) on the RP2040", line 160, to match the correct writing in the Fritzing image shown above, RP2040 pin 36 in place of 39;
Correction of typo in line 346, "pins" in place of "pin"
Signed-off-by: Adrian Rose <adrian@crazyroses.net>
In some condition ，“drvstrength 2” does not work. According to page 17, some mosfets need “drvstrength” set to 0 .
From datasheet rev1.15, the DRVSTRENGTH reset default is 0 . (instead of 2)
Signed-off-by: Albert Lin <vcore85@gmail.com>
The stalled_bytes counter refers to the number of bytes that are not
yet eligible for transmission. However, the naming leads to confusion
as it could be interpretted as an inability to transmit data. Rename
to upcoming_bytes to try to avoid that confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an optional REGISTER parameter to DUMP_TMC so that the output is more filtered/cleaner for manual TMC calibration.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Ability to specify `VELOCITY` as a parameter for SET_TMC_FIELD. Useful for configuring at runtime the TSTEP based fields of the driver.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Previously, the globalscaler was calculated during the config parsing and set to a fixed value. If the current was changed for any reason after the initialization, only IRUN and IHOLD would be changed. This however caused issues:
- If the new current was lower, then the resolution of the possible current values would be low since there are only 32 IRUN/IHOLD steps.
- If the new current was higher, it wouldn't actually work since IRUN and IHOLD are capped at 31, so it wouldn't be possible to increase the current without increasing globalscaler.
With this commit, the globalscaler is recalculated whenever necessary in order to ensure the correct range of IRUN/IHOLD is used.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Michael Jäger