Works for unmodified stock Artillery Sidewinder X2,
year 2022 with Artillery Ruby v1.2 mainboard.
All by default connected things are working fine.
Build firmware with architecture STM32F401 with "No bootloader".
Other settings keep ther defaults
Signed-off-by: Frank Roth <developer@freakydu.de>
If a maximum acceleration is changed between two consecutive moves,
this allows to correctly compute the junction velocity between them.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
it seems I made an error with my code for the SKR 3, and I copied the code from the wrong host , this PR fixes that. I have just retested with the right code and works as expected, this is confirmed by @adelyser who brought the issue to my attention.
Signed-off-by: James Hartley <james@hartleyns.com>
Fix gpio function selection for PIO1 usage.
Minor variable name changes.
Allow scheduling tx "matched" event after a crc match.
Allow for up to 5 passive bits after unstuf_clear_state().
Pause PIO "rx" bit reception after 10 passive bits.
Signal the CPU to process data every 10 read bits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Corrected the build instructions for the TH3D EZBoard V2 to include the command to convert Klipper.elf to a SREC bin format named firmware.bin. The SREC format is required for the bootloader installed on the board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
As discussed with Arksine, he has created new working settings for the Creality 4.2.x boards as the original 4.2.7 entry did not work, plus addition of SKR2 and SKR3. Tested on 4.2.2 and SKR2 and SKR3EZ.
These are using the new skip_verify functionality that was recently merged due to them using SDIO
Also removed a double definition for `monster8` it was in main definitions and aliased.
Signed-off-by: James Hartley <james@hartleyns.com>
This adds a gcode command that can be used insight the slicer to pass the total layer count and current layer information.
Signed-off-by: Stefan Dej <meteyou@gmail.com>
M105 expects get_temp method. Module crashes when gcode_id parameter
is set and M105 called. Add methods as hotfix.
Signed-off-by: Robert Pazdzior <robertp@norbital.com>
Introduce a new handle_fault() method to handle processing of sensor
faults. This simplifies the calc_temp() methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the fault information explicitly in the query_thermocouple fault
field for max6675, max31855, and max31865.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
* Update printer-anycubic-vyper-2021.cfg
better pause and end print, beeper support, mroe accurate value.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
delete unnecessary gcode
* Update printer-anycubic-vyper-2021.cfg
remove unneccessary part.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
according to https://www.klipper3d.org/Example_Configs.html point 7f
delete field values that are set to their default value
* Update printer-anycubic-vyper-2021.cfg
small change
* Update printer-anycubic-vyper-2021.cfg
If a tmc driver can't find the stepper config section it reports a
"missing microsteps" error which can be confusing. Provide a more
explicit error message.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As found on discord bt user David Carey.
uart_address for y and z are swapped. Discovered while setting up sensorless homing.
Signed off by: James Hartley <james@hartleyns.com>
Added a SET_DIGIPOT command to the mcp4018 implementation.
Previously the mcp4018 was read only, and set at the time of
configuration. This allows you to change the value during a
print, which is needed for some older printers that need to
lower the stepper current during preheating.
Signed-off-by: Jake Bordens <jake@allaboutjake.com>
freakyDude