Now that the mcu objects can be created prior to connecting to the
mcu, it is no longer necessary to separate the init and build_config
phases in the high-level code. Move the mcu objection creation from
the build_config phase to the init phase and eliminate the
build_config phase.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of requiring the user enter velocity and accel parameters for
extrude only moves, calculate sane defaults from the printer's maximum
velocity and accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the config file so the maximum accel and velocity are specified
in the "printer" section instead of the individual "stepper" sections.
The underlying code limits the velocity and accel of the toolhead
relative to the print object, so it makes sense to configure the
system that was as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of checking the endstop trigger directly after a retract move,
verify some distance is traveled during the following homing
operation. This reduces the amount of synchronization between mcu and
host during homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the storage of the stepper location from the kinematic classes to
the low-level mcu_stepper class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow an EndstopError to be raised without a destination position.
Introduce EndstopMoveError wrapper so that current callers can
continue to pass in a move destination.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the scheduling of the final homed position (which takes into
account the stepper phases) so that it is scheduled from the kinematic
classes instead of from the toolhead class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create the Homing class in the gcode handler instead of in the
kinematic classes. This will make it easier to pass error messages
back to the user.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create the QueryEndstops in the gcode handler instead of in the
kinematic classes. This simplifies the gcode handler as it can
directly register its response callback.
Also, store the stepper name in the stepper class. Also, propagate
the print_time of the query request to the mcu_endstop class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commits f0cefebf and 8f331f08 changed the way the code determined what
steps to take on fractional steps. Unfortunately, it was possible in
some situations for the C code to round differently from the python
code which could result in warnings and lost steps.
Change the code so that all fractional step handling is done in the C
code. Implementing the step rounding logic in one location avoids any
conflicts.
In order to efficiently handle the step rounding in the C code, the C
code has also been extended to directly send the "set_next_step_dir"
command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Invert the default meaning of the stepper direction pin. Instead of
treating a low value as position motion, treat a high value as
positive motion. This matches what other firmwares do, and it matches
what common stepper motor drivers document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The existing code calculates the number of steps in a move and then
spreads them out evenly throughout that move. Change the code so that
step timing is based on where the head is commanded to be relative to
the axis step locations. This makes the timing more accurate - in
particular the axis velocities will be more accurate during cornering
introduced by the lookahead code. It also results in slightly
smoother stepper motion which results in better step compression.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't use step_dist for the "distance along the line of movement per
step" as it's too similar to the stepper.step_dist variable. Use the
name "move_step_d" instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the start position (in addition to the existing end position) in
the Move class. The start position can be useful to the kinematic
classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename get_homed_position() to get_homed_offset() and return the
endstop position delta in steps instead of an absolute position
relative to position_endstop. The conversion to absolute positions
can be dependent on the type of kinematics in use, so is inappropriate
to do in the low level stepper.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a check_move() method in the extruder and cartesian
kinematic classes. This allows the lower level classes to verify the
contents of the move prior to queing that move.
The speed and acceleration handling for special Z and extrude only
moves are also moved from the generic toolhead class to the low-level
classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enhancing the precision of endstop switches by also
inspecting the phase of the stepper motor when the endstop triggers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the code so that the kinematic class (currently just
cartesian.py) has more control over the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the owner of the stepper object to cacluate the maximum step
jerk velocity. This is used to ensure there is no communication error
between mcu and host.
Disable checking of jerk velocity for extruder stepper motors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a new python file (extruder.py) to control the extruder heater
and stepper motors. This separates the extruder control logic from
the cartesian robot code - making it easier to customize both the
kinematic control of the robot as well as the extruder.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
All users of max_step_velocity and max_step_accel end up multiplying
by step_dist anyway, so it's easier to store max_velocity and
max_accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate out the low-level stepper motor kinematics handling from the
ToolHead class into its own class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Perform all acceleration calculations and lookahead checks in
millimeters using the cartesian coordinate system of the request. The
conversion to step coordinates is now done at the time of the step
timing creation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor