It appears some bltouch "clones" do not report the probe as triggered
when put in "touch mode" while the pin is raised. Add a config option
to allow users to disable the test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some of the bltouch implementations may only respond to a probe event
with a 5ms pulse. Make sure to check the signal pin at least every
millisecond to ensure no signal is lost.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To deal potential z scaling when fade is enabled, a fade_target option has been introduced. This option may either be set to 0.0 or any z position within the range of the mesh. A value of 0.0 will result in previous behavior, where z adjustment phases out until no further adjustment is added. A non-zero value will phase out adjustment until the target has been reached, after which the rest of the print will be offset along the z axis by the fade_target. By default the fade_target will be calculated as an average of the mesh.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Due to various potential issues with fading out z-adjustment, it is better to disable by default and allow users to opt-in.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add a self.all_framebuffers variable and change self.vram to only
contain the new display data. This allows the main code to access the
self.vram member variable without the need to index for current/old
data. (It also updates the code to match the latest st7920 and
hd44780 code.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.
Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]
For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo
This patch add one option to servo configuration:
enable: <False/True> # default True
It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.
Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
This allows SX1509 pins to be used as temperature fans and heater fans. Heaters are still disallowed.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
The atmega328p is basically the same as the atmega328 - add explicit
support for it so that avrdude doesn't complain while flashing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the process_batch() method so that it will not interleave
commands read from the input fd with the batched commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 459e5219 added a special case to the boundary checks to permit
homing moves. In some cases, the second home retract could also be
outside the normal boundary checks - extend the special case to also
permit that move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gitdir previously could be absent and produce a version of "" in
spite of checks for it. Fixed.
Parent directories with shlex-interpreted characters in their names
could be misinterpreted. Removed shlex parsing.
Packagers may want to remove the git history to slim down the package
size, so add an option for using a file 'version' in the klippy
directory to set version without using git.
Signed-Off-By: Lucas Fink <software@lfcode.ca>
Kevin O'Connor