The atmega328p is basically the same as the atmega328 - add explicit
support for it so that avrdude doesn't complain while flashing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Sometime bossac reports an error during chip restart. It appears this
error is spurious - just suppress it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Scaling the timer on the system bus has a notable impact on
performance. So, scale the timer within the timer hardware itself.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It appears the sam3x8e has a primitive cache prefetch mechanism (it
prefetches 32 bytes at a time aligned to a 16 byte boundary).
Aligning the main loop in timer_dispatch_many() to a 16 byte boundary
significantly improves performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If sched_try_shutdown() is not inlined into timer_dispatch_many() it
can have a significant impact on benchmarks. (Even though the
function isn't called in practice, the call causes gcc to organize the
function differently.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some older versions of gcc need the __always_inline directive in order
to inline timer_read_time. Inlining that function is important for
performance on the stm32f1.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As long as timer_read_time() is inlined, I get better performance with
gcc -O2 optimization. The binary is also dramatically smaller and O2
better matches the other platforms.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible for the code to stay in the timer irq for up to 100ms,
so serial irqs should have a higher irq priority to prevent them from
being starved. (The timer code disables irqs during event dispatch,
so serial irqs would only be permitted between events anyway.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The usb_cdc code will arrange to call usb_read_ep0_setup() after a
shutdown, so no need to have an explicit shutdown handler.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Call usb_read_bulk_out() before calling command_find_and_dispatch() as
this optimizes the common case where each usb packet contains a single
new message block.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Recent code additions have increased the stack usage and it is no
longer clear that everything will fit in 128 bytes. Increase all
targets to 256 bytes (the atmega2560 was already at 256 bytes).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix travis-ci build failure by forcing the data field of the struct
usb_string_descriptor to be the same type as a 16bit unicode string.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use new usb_read_ep0_setup() function when reading a setup packet -
this allows the low-level usb hardware code to better handle errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A zero length packet should only be sent at the end of a transmission
if the host is expecting more data.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Maintain the state tracking code entirely within a usb_do_xfer()
method. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use "ep0" when referring to endpoint0 - don't use "setup" as that can
be confused with the low-level usb setup token.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega168 doesn't have enough flash space to fit all features -
disable the "bit banging" interfaces to make room.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The bank_id was calculated erroneously. Also unify gpio_in_setup and gpio_out_setup a bit. Also disable make flash for the sam4e8e port as it currently references a version of bossac that is not present on all systems.
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Kevin O'Connor