The Trinamic stepper motor drivers are capable of reporting the
stepper phase - add support for using that capability to the
enddstop_phases module.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Python 2.x ConfigParser doesn't support stripping of trailing '#'
style comments. Do that manually before parsing the config.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only clear the internal sync_print_time flag if the code performs a
regular "lazy" flush of the look-ahead queue. This helps build the
look-ahead queue even when running internal scripts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that "Klipper state" messages are proactively sent, it is
redundant to send the "preparing to restart" message.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When a delta printer has different arm lengths or different endstop
positions then the homing position falls outside of the normal
printable area. Add a special check to the range checking code to
permit this move instead of homing to a position near the actual
homing position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic for performing the second home from the kinematics
classes to the generic homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter, and it
also changed the retract speed. Revert the retract speed change (use
homing_speed when the head retracts).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter; that
parameter needs to also be constrained to the max_z_velocity.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the xor capability of the display to animate the glyphs, which
reduces the number of glyphs needed from 4 to 2. This should make it
easier to add future animations if desired.
Suggested by @marcio-ao.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Based on replies from Issue 652 (https://github.com/KevinOConnor/klipper/issues/652) only Extruder, Bed and Fan icons are changed. Feedrate icon stays untouched.
Signed-off-by: Alexander Fadeev <alfsoft@gmail.com>
The max_accel_to_decel variable must not be greater than the max_accel
variable. Make sure to check this when M204 changes max_accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't require (or permit) the user to specify a stepper_z
position_endstop when using the probe:z_virtual_offset mechanism. In
that case the position_endstop should always equal the probe's
z_offset - so no need to have the user specify it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the code to calculate and track the z_offset via
position_endstop updates. It's simpler to always save and restore the
calculated z_adjust.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't require the config file to specify manual probing. Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all the callers of ProbePointsHelper take a cartesian
coordinate for the probe locations, it's possible to perform averaging
of multi-sample probes within the class. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only call cmd_NEXT() for manual probing. This simplifies the code as
the automatic probing and manual probing have slightly different
probing mechanisms.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all users of ProbePointsHelper use the same
get_probed_position() code, it is possible to implement that locally
within the ProbePointsHelper class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible (and a little simpler) to use cartesian coordinates when
calculating a stable position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Configure the tmc2208 during the 'connect' phase so that a problem
during configuration is properly raised as a config error. Catch
errors during DUMP_TMC and raise them as g-code errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't log a heater verification error if that error is due to the
printer being shutdown for some other reason. Those spurious error
reports can be confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to report an error if the M73 is not between 0 and 100 - just
display the nearest valid value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support using SAVE_CONFIG to store the results of DELTA_CALIBRATE to
the printer config file. Store the low level probe measurements in
the config as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the "stable position" logic from the delta.py kinematics code to
the delta_calibrate.py calibration code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add write_glyph() support to hd44780.py. Update uc1701.py and
st7920.py to support writing single character glyphs via
write_glyph().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the st7920 icon rendering optimizations from display.py to
st7920.py. This simplifies the code for other displays.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It isn't necessary to use the st7920's xor capabilities when drawing
the bed heating animations. This makes it easier to use the icons for
other displays.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an arm is nearly parallel to the bed then that tower's carriage may
have a velocity up to 3 times greater than the toolhead's maximum
velocity (relative to the print). Take that into account when
calculating the stepper's maximum halt velocity.
This fixes some rare "No next step" shutdowns on delta printers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 4573932f allowed move.end_pos to differ from the requested end
position - the toolhead class should use the updated position when
storing its commanded position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible that a g-code transform class may make an extrude only
move appear as a kinematic move due to limitations of double precision
math. Handle this by checking for an inconsequential move distance
instead of checking for a move distance of exactly zero.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Log the details of the MCU prior to attempting to configure the MCU.
This way, the log contains the MCU information even if a configuration
error occurs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the name of the config registration method and pass an explicit
reference to the callback to the new method. This makes the
relationship between mcu registration and build_config() more clear in
the calling code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor