The recommended TOFF time in "standalone mode" according to the
tmc2130 is 4, so use that as the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The extrude_factor and extruder position are specific to the current
extruder, so reset them to default values on a Tn command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common to add commands that dispatch to a particular object
instance depending on the value of a command parameter. (For example,
the command "SET_SERVO SERVO=xyz" wants to be handled by the
particular "xyz" servo instance.) Add a register_mux_command() helper
to gcode.py make it easier to do this.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the common config reading and probe object lookup from the
bed_tilt.py and delta_calibrate.py code into the ProbePointsHelper
class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raise an error during config parsing if the position_endstop is not
between the position_min and position_max. This avoids a confusing
error message during homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
For some reason, Linux creates the pseudo tty with group writable
permissions, but not group readable. Use chmod to allow the device to
also be group readable.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The step speed rounding and the cpu delay must be run after running
the endstop specific preparation code. Otherwise, a delay in the
home_prepare() code could undo those calculations. Specifically, this
could lead to errors on a multi-mcu setup when the Z is homed using a
virtual_z_offset and there is a delay in the activate_gcode section.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't return early on a command error - continue to process remaining
commands and pop commands from the queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the generic spi send/receive code on Linux. Update the replicape
code to use the updated command format.
Also, update the replicape code to turn off the stepper motors on a
shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In order to properly delay BACKGROUND_PRIORITY_CLOCK messages, they
must be 5ms beyond the minimum defined by MIN_REQTIME_DELTA. So, add
both MIN_REQTIME_DELTA and MIN_BACKGROUND_DELTA to the timing of these
messages.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the clock querying messages occur at a similar frequency to other
events on the micro-controller or host, then it's possible for the
load created by those other events to skew the clock synchronization.
In particular, the 500ms lcd screen update could resonate with the 1
second clock query. Use an unusual clock querying frequency to avoid
this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the C code out of the main klippy/ directory and into its own
directory. This reduces the clutter in the main klippy directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a set_shutdown_speed() method so that the heater_fan code does not
need to peek into the fan object's internal members.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing as positive values in that command
result in negative offsets to future g-code commands. Perform the
parameter negation in the M206 command instead of storing it that way
internally.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When using an automatic probe, limit the Z lift speed to be no greater
than the Z probing speed. This can reduce Z jerks during probing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the fan's max power is limited by the config, then scale speed
requests between 0 and max_power. This makes more sense for typical
g-code fan speeds.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If max_accel_to_decel is greater than max_accel in the config, then
just internally limit max_accel_to_decel to max_accel. This makes it
easier to completely disable the max_accel_to_decel feature (as it can
just be set to a high value in the config).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a fully functional STM32F1 port, currently mostly targeting STM32F103
microcontrollers. This requires an 8 MHz XTAL. The maximum possible step rate
is around 282K steps per second.
This uses stm32flash to burn the firmware. The bootloader needs to be started
by setting BOOT0 to 1 and resetting the MCU. There is no automatic bootloader,
unlike on Arduino.
Signed-off-by: Grigori Goronzy <greg@kinoho.net>
Instead of supporting a single linear range for the temperature
lookup, allow multiple ranges to be defined. This makes the lookup
more accurate when a full lookup table is available.
Update the AD595 sensor to use the full table defined in its spec.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor