1b92af6078
display: Add ST7567 display support ( #1540 )
...
Signed-off-by: Dmitry Budaev <condemil@gmail.com>
2019-04-15 21:07:29 -04:00
0a392b6543
menu: initial support for analog buttons ( #977 )
...
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
2019-04-14 11:18:52 -04:00
62bdc2709f
config: Update generic-bigtreetech-skr-v1.3.cfg with e0/e1 defs
...
Use the HE0 for the extruder0 heater and add comments describing the
nominal extruder1 pins.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-06 16:18:15 -04:00
478a916f51
replicape: add support for Linux hardware PWM ( #1443 )
...
The servo pins (P9_14/P9_16) are muxed to the SOCs hardware PWM unit
driven by a 13MHz GP timer. They have to be driven by the linux host
mcu. This commits adds hardware PWM support using the linux sysfs
user space interface.
The servo pins can be specified as "replicape:servo0" and
"replicape:servo1". Removes the "servo0_enable", "servo1_enable"
configuration parameters.
Fixes #1105 .
Signed-off-by: Janne Grunau <janne-3d@jannau.net>
2019-04-06 13:51:51 -04:00
8c54fc8753
config: Minor change to generic-bigtreetech-skr-v1.3.cfg
...
Interpolate is enabled by default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 20:07:13 -04:00
ccc1107dbe
config: Generic board BIGTREETECH SKR V.1.3 config
...
Signed-off-by: Aleksander Sobolewski <aleks.sobolewski@outlook.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 19:56:22 -04:00
1c56ba0ca7
config: Update generic-bigtreetech-skr-v1.1.cfg - make flash should now work
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 19:51:10 -04:00
0615ab5f89
docs: Note the use of bus enumerations in Config_Changes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:30:04 -04:00
bc9fd03dab
atsamd: Use enumerations for buses and reserve pins
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:29:31 -04:00
7e8ecfe177
atsam: Use enumerations for buses and reserve pins
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:29:31 -04:00
be6b29fabf
sx1509: Convert code to use generic i2c bus support
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:29:30 -04:00
2e16be224e
uc1701: make contrast configurable
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-04-02 15:53:16 -04:00
c105adc80b
temperature_fan: Fix. Temperature fan min speed should be used ( #1405 )
...
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
2019-03-28 14:07:40 -04:00
74f9da8376
config: Update description of printer-tevo-flash-2018.cfg
...
Reported by @RadianceNL.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-24 10:56:20 -04:00
9aadc3c7fa
docs: Also note that driver_VSENSE was removed from tmc2660 driver
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 22:40:42 -04:00
871e028c27
config: Document the [include] directive
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:48:15 -04:00
3945905420
config: Minor rearrangement of example-extras.cfg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:46:37 -04:00
efab177645
docs: Note tmc2660 driver_HEND default change from 6 to 3
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:41:32 -04:00
5bcf9f02cf
config: Added Anycubic 4Max printer config file
...
Signed-off-by: Christian Toulon christian@bouncy-studio.com
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 13:02:01 -04:00
f2fbe98454
bed_mesh: enable relative offset bed meshes ( #1323 )
...
Adds parameter for bed meshes to be adjusted relative to a probed point
during calibration. This allows the probe z offset to be ignored for
probes that are not stable over time (for example, the thermal drift of
inductive probes). An endstop other than the probe is then necessary to
determine the bed-nozzle offset.
Signed-off-by: Matt Baker <baker.matt.j@gmail.com>
2019-03-21 10:39:22 -04:00
53290664ee
pins: Document support for '~' to enable pull-down resistors
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-17 21:07:31 -04:00
378402b4d6
config: Update extra extruder pins in generic-rumba.cfg
...
Reported by @jakep82.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-14 11:48:25 -04:00
b455f1fbe1
config: Reduce the stepper current in the example printrboard config
...
Reported by @drphil3d.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-14 10:44:02 -04:00
01c8705d92
config: Add printer-tevo-flash-2018.cfg
...
Reported by @RadianceNL.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-14 10:27:37 -04:00
d3f6dad853
controller_fan: Allow multiple controller_fan sections to be defined
...
It may be necessary to define multiple fans, so allow each config
section to be named.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 13:57:01 -04:00
19c7955f2a
config: Improve the description of z_tilt z_positions
...
Reported by @sensille.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 12:24:34 -04:00
f5b10f0c13
lpc176x: Add support for flashing via "make flash"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 22:22:41 -05:00
5c0a2479be
screws_tilt_adjust: Add new screws_tilt_adjust tool ( #1367 )
...
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
2019-03-08 11:47:17 -05:00
fcaa75f014
config: Update default spi speed in tmc2660 description
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:27:50 -05:00
563bc37073
tmc2130: Rename driver_BLANK_TIME_SELECT to driver_TBL
...
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:25:19 -05:00
e96b71a9a3
tmc2660: Use helper functions for register access and simplify TMC2660 parameters
...
sense_resistor is now a mandatory parameter for tmc2660 blocks. Duet2 users should use a value of 0.051
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
4541f16cd9
tmc2660: Add vsense_resistor config parameter
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
47d51d8613
config: Update verify_heater description
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 10:55:46 -05:00
8e8063a9d9
config: Fixed Duet2 reversed heater/fan output pins ( #1350 )
...
Using the Duet2 config as a base for your own config will no longer turn
on all heaters and fans at full power during the (almost inevitable) MCU
shutdown that will occur during initial Klipper setup.
Signed-off-by: Benoit Miller <github@benoitmiller.ca>
2019-03-04 13:37:38 -05:00
d62a41b930
manual_stepper: Add support for moves with acceleration
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-03 13:38:10 -05:00
69491e2dab
filament_switch_sensor: update documentation
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-03-01 00:45:51 -05:00
c8d7e28a35
atsamd: Add support for programming SERCOM pins
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:40:44 -05:00
8446f28850
config: Add buttons to printer-tronxy-x5s-2018.cfg
...
Reported by @blackyarr.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:09:30 -05:00
b6589406d4
temperature_sensor: Add generic temperature sensor support
...
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 13:15:56 -05:00
3887ad4fce
heater: Support generic gcode_id registration for sensors
...
Support reading a "gcode_id" parameter from heater/sensor config
sections.
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-26 12:07:00 -05:00
f7d8854587
bed_mesh: simplify configuration
...
The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-02-25 13:34:14 -05:00
80c8bd8b4d
bed_screws: Add a helper tool for leveling bed screws
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-24 00:49:47 -05:00
834b9e3d92
config: Warn that cycle_time may not match when using hardware_pwm
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-19 13:19:32 -05:00
cc4ecef88b
mcp4018: Add initial support for the mcp4018 digipot
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-16 08:16:37 -05:00
0f674ef407
tsl1401cl_filament_width_sensor: Filament Width Sensor Support ( #1132 )
...
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
2019-02-14 10:13:48 -05:00
c6d1d1bd8c
Merge pull request #1242 from john--/pr_generic_heater
...
Generic Heater Support
2019-02-14 10:08:26 -05:00
6316b2c1b6
Generic Heater Support
...
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
2019-02-14 01:15:11 +00:00
a03e31809f
config: Example config file for a stock 250mm build VORON2 printer
...
Example config file for a stock 250mm build VORON2 printer that
matches the manual diagrams exactly for the controller layout and pins
used.
Signed-off-by: Ben Warren <boffdroid@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-13 12:07:20 -05:00
98ed462865
spi_software: Implementation of software spi
...
Signed-off-by: Matt Janus <FragginRight@variabl.es>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-13 11:52:20 -05:00
2d7c3a84ee
manual_stepper: Add an "extras" module for manually controlling a stepper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:38:13 -05:00
Dmitry