Specify the arm architecture flash bootup address for each chip type
in Kconfig using a new FLASH_BOOT_ADDRESS setting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This will hide features in the Klipper Display menu that isn't applicable
for the machine, therefore we can add extra alignment tools in the Control
menu as well.
Also conditionally displays Setup/Calibration options.
Signed-off-by: Nickolas Grigoriadis <nagrigoriadis@gmail.com>
The stm32h7 uses similar usart hardware as the stm32f0 and stm32g0
chips. Use the same code implementation for all these chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an USART RX overrun happened on a stm32g0/f0/h7, the ORE flag
would get set by hardware. This flag would also trigger an interrupt.
The problem was that this flag was never cleared on these 3 mcu families
since the ORE flag clear sequence is different to all of the older
chips.
Since the ORE flag is not used in any meaningful way anyway, it was
disabled during the init sequence.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
According to ADXL345/ADXL343 datasheets, at 3.3V supply voltage,
which is most frequent in the various boards, the sensitivity of
X and Y axes changes to 265 LSB/g from 256 LSB/g at 2.5V.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Works for unmodified stock Artillery Sidewinder X2,
year 2022 with Artillery Ruby v1.2 mainboard.
All by default connected things are working fine.
Build firmware with architecture STM32F401 with "No bootloader".
Other settings keep ther defaults
Signed-off-by: Frank Roth <developer@freakydu.de>
If a maximum acceleration is changed between two consecutive moves,
this allows to correctly compute the junction velocity between them.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
it seems I made an error with my code for the SKR 3, and I copied the code from the wrong host , this PR fixes that. I have just retested with the right code and works as expected, this is confirmed by @adelyser who brought the issue to my attention.
Signed-off-by: James Hartley <james@hartleyns.com>
Fix gpio function selection for PIO1 usage.
Minor variable name changes.
Allow scheduling tx "matched" event after a crc match.
Allow for up to 5 passive bits after unstuf_clear_state().
Pause PIO "rx" bit reception after 10 passive bits.
Signal the CPU to process data every 10 read bits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Corrected the build instructions for the TH3D EZBoard V2 to include the command to convert Klipper.elf to a SREC bin format named firmware.bin. The SREC format is required for the bootloader installed on the board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
As discussed with Arksine, he has created new working settings for the Creality 4.2.x boards as the original 4.2.7 entry did not work, plus addition of SKR2 and SKR3. Tested on 4.2.2 and SKR2 and SKR3EZ.
These are using the new skip_verify functionality that was recently merged due to them using SDIO
Also removed a double definition for `monster8` it was in main definitions and aliased.
Signed-off-by: James Hartley <james@hartleyns.com>
This adds a gcode command that can be used insight the slicer to pass the total layer count and current layer information.
Signed-off-by: Stefan Dej <meteyou@gmail.com>
M105 expects get_temp method. Module crashes when gcode_id parameter
is set and M105 called. Add methods as hotfix.
Signed-off-by: Robert Pazdzior <robertp@norbital.com>
Introduce a new handle_fault() method to handle processing of sensor
faults. This simplifies the calc_temp() methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the fault information explicitly in the query_thermocouple fault
field for max6675, max31855, and max31865.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor