Move the definitions of the default thermistors from thermistors.py to
the temperature_sensors.cfg file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the default list of sensor modules from heaters.py to a new
temperature_sensors.cfg config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9ecddd1b fixed a serious error (introduced in 7d95a004). Force
a protocol version change so users are aware of the need to update the
mcu code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 7d95a004 introduced a defect - if the cached timer pointed to
by last_insert did not reschedule itself then the cache would not be
in a valid state and other active timers may not get properly
rescheduled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an optimized step function for drivers that support stepping on
both rising and falling edges of the step pin. Enable this
optimization on 32bit ARM micro-controllers. Automatically detect
this capability in the host code and enable on TMC drivers running in
SPI/UART mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the STEP_DELAY Kconfig option and replace it with a per-stepper
step_pulse_duration printer.cfg config option.
The AVR code will continue to have optimized code to step and "unstep"
in the same function (which is automatically activated when the step
delay is 40 ticks or less). This change removes the Kconfig option
for single function step/unstep on 32bit processors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove support for default_parameter_xxx config options. Remove
support for direct access to command parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using unicode() types on Python2 as it can lead to subtle
errors.
Also, accept utf8 on gcode input (instead of just ascii).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The floating point unit must be enabled in order to use it and Klipper
does not currently implement that. Newer versions of gcc may spill
registers to the floating point unit causing failures.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This resolves an issue where the timer can get stuck
in an attempt to transition from Ready to Idle if
the printer is shutdown.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Tracking of the last reset is no longer needed after commit 8f76e53c.
Remove the code tracking that status and remove the flag definition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some architectures do better if the global variables accessed from the
timer dispatch code are in a struct.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code automatically reduces the hold_current so that it is no
greater than the run_current. However, this could lead to confusing
behavior if one reduced and then increased the run_current via
SET_TMC_CURRENT commands. To avoid that, this change adds support for
tracking the requested hold_current - thus changes to run_current
don't subtly alter the hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some versions of gcc, in some cases, decide that it is OK to move the
read to `INTR` to right after clearing the `SETUP_REC` bit of
`SIE_STATUS`, instead of after the `memcpy`.
The rp2040 datasheet doesn't appear to say anything about how quickly
the `SETUP_REC` bit will be cleared in `INTR`, but regardless the
compiler should not be re-ordering the read like this.
Here we force the correct ordering using a memory barrier.
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
Example default config for Tronxy XY-2 Pro.
It is default config for printer Tronxy XY-2 Pro (mainboard Chitu V6). This config based on config for Tronxy X5SA with mainboard Chitu V6.
Signed-off-by: Konstantin Bazhenin <kby@list.ru>
Kevin O'Connor