Remove support for configuring "static" pins in output_pin module. A
"static" pin only saves a few bytes of memory in the micro-controller.
The savings does not justify the increased code complexity.
Deprecate the static_value parameter to warn users. In the interim, a
static_value parameter will set both value and shutdown_value
parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for maximum filament diameter to hall filament width sensor.
If the diameter of the filament diameter is larger than the limit, the
virtual runout sensor will trigger. The default value is set to maximum
flow adjustment threshold to prevent oversized filament from clogging.
Signed-off-by: Sami Haahtinen <ressu@ressukka.net>
Note that the max_accel parameter is the actual acceleration used in
most movements.
Note that the accel/velocity limits can be changed using the
SET_VELOCITY_LIMIT command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extends the BMxx80 category with support for the older BMP180 sensor, providing temperature and humidity output.
Signed-off-by: VAXXi Popescu <github@vaxxi.net>
The output_pin module is only capable of updating an output pin at
most once every 100ms. Add a new pwm_tool module that is capable of
queuing updates in the micro-controller and thus allowing for much
higher update rates.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Previous version of the code assumed that dual carriages home away
from each other, which is not true on some machines, which have the
second dual carriage homing on the first carriage. The new code
correctly identifies the relative order of the carriages now.
This fixes discrepancies between the documentation and the actual
implementation of the carriages kinematic ranges calculation.
Notes about dual_carriage homing and proximity checks changes
Fixed clearing of homing state after homing in certain modes
In case of multi-MCU homing it is possible that the carriage position
will end up outside of the allowed motion range due to latencies in data
transmission between MCUs. Selecting certain modes after homing could
result in home state clearing instead of blocking the motion of the
active carriage. This commit fixes this undesired behavior.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Implements AxisTwistCompensation, and Calibrater
Supports calibration of z-offsets caused by x gantry twist
Modify PrinterProbe._probe function to check if the probed z value should be adjusted
based on axis_twist_compensation's configuration
Add documentation for [axis_twist_compensation] module
Signed-off-by: Jeremy Tan <jeremytkw98@gmail.com>
COPY and MIRROR mode implementation
Correctly apply input shaper params to new dual_carriage
Added SAVE_/RESTORE_IDEX_STATE commands
Documentation updates for the new IDEX modes
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
The reference to my_nozzle_fan is misleading and could cause people to skip over the [fan] definition and assume this is the parts/print cooling fan. Alias changed to reflect heatbreak_cooling_fan as used in most configs that have a controllable hotend fan.
Signed-off-by: James Hartley <james@hartleyns.com>
The control bytes for the AHT20 and AHT21 are identical to the AHT10, but I had not been able to test just yet to ensure the sensor code supported the other sensors. I've wrapped up testing and updated the comments/docs to reflect this additional support.
Signed-off-by: Scott Mudge <mail@scottmudge.com>
In some condition ，“drvstrength 2” does not work. According to page 17, some mosfets need “drvstrength” set to 0 .
From datasheet rev1.15, the DRVSTRENGTH reset default is 0 . (instead of 2)
Signed-off-by: Albert Lin <vcore85@gmail.com>
Make all the microstep lookup table registers configurable via the
config file. It also loads the default values.
TMC220x and TMC2660 do not support this feature.
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
The reference to the linux mcu was helpful to understand what a linux mcu was but didn't help with understanding the technical reasons why it's not supported.
Signed-off-by: Karl Bowden <karl@bearded.sexy>
Kevin O'Connor