If a maximum acceleration is changed between two consecutive moves,
this allows to correctly compute the junction velocity between them.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Allow a larger velocity, accel, and square_corner_velocity than what
is specified in the config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The min_stop_interval safety check is fragile and leads to a notable
amount of complexity. Avoid these issues by not programming this
safety check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a dwell() to the start of drip_move() to ensure that input_shaper
movements scheduled in advance of the nominal move time aren't
scheduled prior to the homing start. (Otherwise the stepper may move
prior to endstop checking, which can corrupt the "no movement"
checks.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the get_status() axis_minimum and axis_maximum fields in
advance so that they don't need to be calculated on each get_status()
call.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The "status" and "printing_time" are now available in the
"idle_timeout" module, so no need to report them from toolhead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper function for submitting relative movements. This
function will also automatically ensure gcode.reset_last_position() is
called.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate a "toolhead:set_position" event on a call to
toolhead.set_position() and use that event to automatically call
gcode.reset_last_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If self.kin_flush_delay changes after a G4 dwell command (or other
non-kinematic time update) then it could lead to "internal step
compression" errors. Make sure to handle this case in
flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the endstop code to return its trigger completion object during
home_start(). Update the toolhead class to take a completion object
(instead of creating its own). This reduces the number of
intermediate callbacks needed during a homing operation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a mechanism for obtaining the print_time via a callback instead of
by flushing the look-ahead queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update code that modifies the low-level kinematics handlers to first
call toolhead.flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't transition to the normal movement state if there aren't any
moves actually ready to be processed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly disable all the stepper motors on a global motor_off() from
the StepperEnable() class in stepper_enable.py. This simplifies the
toolhead and kinematic classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the ratio of axis distance to total move distance (axis_d /
move_d) and store in a new member variable axes_r. This avoids
needing to recalculate the value in other code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only track a single acceleration movement in a 'struct move' instance.
Break the classic trapezoid movement (accel, cruise, decel) into three
separate movements. This simplifies the calculation logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Load all items from the look-ahead queue into the trapezoid velocity
queue, and then flush that queue by time. This prevents the host cpu
from being starved on very long moves (which may require a large
number of steps to be generated). It also improves the overall
performance.
With the batch flushing logic in place, it is no longer necessary to
split homing moves up.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Dmitry Butyugin