Lines 94 and 97. Fan speed should be 1 and not 0.5
removed lines to use default settings.
[heater_fan hotend_fan]
pin: PG14
[fan]
pin: PG13
Signed-off-by: Scott Schering <sschering@gmail.com>
The fan pin PA0 is not correct for the 2021 revision of the CR-6 SE using the
4.5.3 revision of the Creality board. Changed the pin to PB15 in order to
get it working
Signed-off-by: Filip Trplan <filip@trplan.si>
TMC2130/5160 can make use of `spi3`, which is operated on the software SPI pins in the current configuration. The supplied defaults for software SPI do not currently work.
Heater0 pin was marked incorrectly, should be `PB0`
Signed-Off-By: Wijnand Modderman-Lenstra <maze@maze.io>
Many non-English speaking countries use a comma as a decimal separator for printed numbers. This can create some confusion in documentation and config files when not surrounded by contextual clues like parenthesis. Improve documentation by adding spaces to coordinates.
Signed-off-by: Paul McGowan <mental450@gmail.com>
There is no reason to explicitly set the interpolate flag to true in
the example configs as that is already the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the documentation recommends that hold_current not be set,
update the example config files to not specify a hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Updates for generic-bigtreetech-skr-2.cfg to include comment on newly shipped board with STM32F429 instead of the original STM32F407
Signed-off-by: James Hartley <james@hartleyns.com>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Example default config for Tronxy XY-2 Pro.
It is default config for printer Tronxy XY-2 Pro (mainboard Chitu V6). This config based on config for Tronxy X5SA with mainboard Chitu V6.
Signed-off-by: Konstantin Bazhenin <kby@list.ru>
This commit contains a configuration for the Anycubic Vyper printer from 2021.
It uses a clone of the STM32F103 chip named GD32F103.
There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
since there are no different changes in the Anycubic Marlin firmware.
The LCD is not supported yet (might work, but didn't try yet).
Signed-off-by: Marc Neuhaus <marc@neuhaus.nrw>
Signed-off-by: Manuel Fichtner <manuel.fichtner@me.com>
Fixing initial rotation distance on Thinker S stocker extruder
Removing author information
Fixing Z Axis homing speed as it was too fast.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
This config I created and fully tested on my own printer Anycubic 4Max Pro 2.0. This works fine! Please note that this printer is different from the Anycubic 4MAX.
Signed-off-by: Alexander Usachev <int_0x21@protonmail.com>
This is just a short inline comment about Bigtreetech's implementation of the "anti-reversal stepper protection" and the way it should be handled in the Klipper printer configuration.
Signed-off-by: Jerry Chapman <truckershitch@hambone.e4ward.com>
The atmega328pb has officially named these pins as PE2 and PE3, so use
that naming scheme instead of the previous Klipper invented names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M300 example macro now sets the PWM cycle time to generate the requested
frequency. 'scale' did not have the desired effect. Duty cycle is now
fixed at 0.5. All S parameter values less than 1 generate a 1Hz 'tone'
to avoid division-by-zero.
Signed-off-by: Stefan Holst <mail@s-holst.de>
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
Information and some lines verbatim were sourced from the official BigTreeTech Octopus
GitHub repository to make this configuration as well as existing configurations in the same
folder as this one
Signed-off-by: Charles Pickering <charles.pickering@live.com>
Add a pin definition to enable motor power and add a warning about
initial faulty SKR2 boards.
Reported by @FHeilmann.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds Duet3 Mini Config with support for expansion header
Signed-off-by: Luke Ashley <Luke@Lukeslab.online>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To support continuous belt printing, add nestable repeat
loop support via an `[sdcard_loop]` module.
Supported G-Code:
- SDCARD_LOOP_BEGIN COUNT=n ; Loop for N times, or infinitely if N is 0
- SDCARD_LOOP_END ; End of loop
- SDCARD_LOOP_DESIST ; Complete all loops without iterating
Marlin M808 compatibility example in `config/sample-macros.cfg`:
- M808 Ln ; Loop for N times, or infinitely if N is 0
- M808 ; End of loop
- M808 K ; Complete all loops without iterating
Added unit tests in test/klippy/sdcard_loop.test
See https://reprap.org/wiki/G-code#M808:_Set_or_Goto_Repeat_Marker
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Change all the example config files to use either 0 or 999999 for
stealthchop_threshold (as is recommended in the TMC_Drivers.md
document).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
A working configuration example for Tronxy X5SA Pro printer (https://tronxy.com/x5s-series/x5sa-pro.html) with no Touchscreen funcionalities because separated LCD firmware needed.
Silent TMC2225 drivers soldered on board.
The Self-levelling plate sensor is a blue Tronxy XY-08N model.
Direct Drive is a Titan Extruder Clone "3:1" gear ratio.
Signed-off-by: Morgan Barresi <morganfw@gmail.com>
Improvements and fixes based on feedback:
* Make speeds and limits more conservative
* Fix Y endstop position
* Improve IR bed leveling
* Fix filament runout pin
Signed-off-by: Justin Schuh <code@justinschuh.com>
Lorenzo