Create a copy of the dictionary prior to updating the the variable field.
This fixes an issue where webhooks holds a reference to the variables
dict returned by get_status().
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the definitions of the default thermistors from thermistors.py to
the temperature_sensors.cfg file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the default list of sensor modules from heaters.py to a new
temperature_sensors.cfg config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9ecddd1b fixed a serious error (introduced in 7d95a004). Force
a protocol version change so users are aware of the need to update the
mcu code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an optimized step function for drivers that support stepping on
both rising and falling edges of the step pin. Enable this
optimization on 32bit ARM micro-controllers. Automatically detect
this capability in the host code and enable on TMC drivers running in
SPI/UART mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the STEP_DELAY Kconfig option and replace it with a per-stepper
step_pulse_duration printer.cfg config option.
The AVR code will continue to have optimized code to step and "unstep"
in the same function (which is automatically activated when the step
delay is 40 ticks or less). This change removes the Kconfig option
for single function step/unstep on 32bit processors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove support for default_parameter_xxx config options. Remove
support for direct access to command parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using unicode() types on Python2 as it can lead to subtle
errors.
Also, accept utf8 on gcode input (instead of just ascii).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This resolves an issue where the timer can get stuck
in an attempt to transition from Ready to Idle if
the printer is shutdown.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
The code automatically reduces the hold_current so that it is no
greater than the run_current. However, this could lead to confusing
behavior if one reduced and then increased the run_current via
SET_TMC_CURRENT commands. To avoid that, this change adds support for
tracking the requested hold_current - thus changes to run_current
don't subtly alter the hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Scale the max_z_velocity limit by the amount of movement in the Z.
This should improve bed_mesh and vase mode prints on delta printers.
Reported by @hywelmartin and @dalegaard.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The backport of Python3's configparser causes issues when there is
unicode characters in the config file. To avoid introducing new
errors, go back to using the Python2 version of ConfigParser when
running on Python2.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Explicitly specify the comment_prefixes as regular Python2 strings -
otherwise the configparser wont ignore non-ascii characters in
comments.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Newer versions of configparser no longer default to ignoring trailing
comments that start with a semicolon. Add that setting explicitly to
avoid breaking existing config files.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a test case to verify that every optional module successfully
loads on both Python2 and Python3. This is intended to catch syntax
and module imports that are not compatible between Python versions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Pedro Lamas