197030c684
docs: Update FAQ to reference Bootloaders.md on "make flash" failure
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-22 10:07:34 -04:00
b7bc96c3b2
neopixel: Add initial support for "neopixel" leds
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-12 21:44:01 -04:00
28aa2f507a
endstop: Rename mcu end_stop commands to endstop
...
Rename the commands.
The main reason for this change is to force a micro-controller code
updated (due to important bugfix in 7fefe52d
2019-07-12 08:10:53 -04:00
0343d0c73a
firmware_retract: Remove z_hop support
...
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.
The z_hop support is therefore being removed until these issues can be
fixed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 19:25:56 -04:00
364c22fe84
probe: Rework the PROBE_ACCURACY command parameters
...
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10. Instead, use the "retract
distance" method that is used for normal multi-sample probing.
Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 15:21:09 -04:00
d4d8bf795b
filament_switch_sensor: add SET_FILAMENT_SENSOR gcode
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-07-10 09:57:46 -04:00
ea6f30bd99
docs: Update Protocol.md to use enumerations for pins
...
Now that pins use enumerations, update the set_digital_out command
examples.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-09 14:17:28 -04:00
e7dd313a96
docs: Add information on using OpenOCD to Bootloaders.md
...
Add information on using OpenOCD. Add information on flashing the
SAMD21 and SAMD51 with OpenOCD.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-09 13:37:17 -04:00
e19a41d0dd
docs: Add documentation for [delayed_gcode]
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-07-01 11:09:30 -04:00
57eb0e8975
docs: Update for latest changs to skew_correction
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-29 10:58:46 -04:00
3a3dfd51b9
docs: Add CLEAR_PAUSE to G-Codes.md
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-28 12:44:49 -04:00
d9d94c858a
docs: Add skew_correction.md to Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-27 09:50:17 -04:00
a3b4543c97
skew_correction: add documentation
...
Signed-Off-By: Eric Callahan <arksine.code@gmail.com>
2019-06-26 20:16:35 -04:00
d9bddc35a1
docs: Add information on running the regression suite locally
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 17:59:23 -04:00
a2c7fd369c
docs: Note tmc2209 and tmc5160 support in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 12:28:39 -04:00
ba27e0aa02
docs: Warn against using "PreloadVE" on KISSlicer
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-23 12:18:24 -04:00
83e6c01ada
probe: Allow probe parameters to be specified as g-code parameters
...
Add PROBE_SPEED, SAMPLES, SAMPLE_RETRACT_DIST, SAMPLES_TOLERANCE,
SAMPLES_TOLERANCE_RETRIES, and SAMPLES_RESULT parameters to the PROBE
command (and to commands that indirectly invoke a probe).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-21 14:44:28 -04:00
8cce3cc8e7
graphstats: Add support for interactive graphs
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-19 21:12:26 -04:00
8b00580884
gcode_macro: Parse variable_X parameters using ast.literal_eval()
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 19:33:31 -04:00
a541c2f60e
docs: Update Config_Changes.md with "samples" move to probe config section
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:15:47 -04:00
97adca18c4
docs: Update Delta_Calibrate.md with probe location bias info
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
e061029b3a
docs: Update Probe_Calibrate.md with information on common probe errors
...
Add a section describing PROBE_ACCURACY, describing probe location
bias, and describing probe temperature bias.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:08:58 -04:00
5989f7a8a6
firmware_retraction: Implementation of tuneable G10/G11 firmware retraction ( #1617 )
...
This supports getting and setting of retraction parameters without
having to restart klippy.
Signed-off-by: Len Trigg <lenbok@gmail.com>
2019-06-06 09:10:09 -04:00
3f96c0abd8
docs: Minor wording change to Command_Templates.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 10:39:43 -04:00
962c48ecf7
docs: Fix github pages "liquid" rendering of Command_Templates.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 10:31:03 -04:00
94c1ad7241
docs: Add an initial Command_Templates.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
a68f577adf
gcode_macro: Add support for SET_GCODE_VARIABLE command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
ac8f6dfe20
gcode_macro: Rename "status" helper to "printer"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
a238ec6f98
idle_timeout: Add SET_IDLE_TIMEOUT gcode
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-06-04 09:46:26 -04:00
c54b8da530
gcode: Add support for SAVE_GCODE_STATE and RESTORE_GCODE_STATE commands
...
Add commands to save and restore the current g-code state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-31 10:23:56 -04:00
d6b69938ab
gcode: Don't apply the SET_GCODE_OFFSET to the next g-code command
...
The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command. (In particular,
when the following command is an extrude only move - as in
issue #1289.)
Don't apply the offset immediately. Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-26 11:19:15 -04:00
500f37821d
docs: Improve bltouch v3 documentation
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-26 11:09:32 -04:00
c77285287b
docs: Try to be more clear that the "paper test" steps need to be run
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-24 22:44:00 -04:00
6c4c26c319
docs: Minor wording change to Bed_Level.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-23 19:31:44 -04:00
1856f95503
docs: Recommend OctoPrint 1.3.11 or later
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-20 23:01:04 -04:00
ad12ffa981
docs: Use markdown syntax for http links in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-20 17:19:33 -04:00
fd1dff3f02
docs: Fix numbering in FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-08 16:48:14 -04:00
73fd292637
docs: Update "avr restart=command" FAQ to point to bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-07 23:02:20 -04:00
8524602b6e
docs: Fix inclusion of CONTRIBUTING.md in the automatic html generation
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 23:10:32 -04:00
17dd6e5097
docs: Fix markdown table layout in html rendering
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:56:56 -04:00
b5f79d5e77
docs: Simplify main html page now that there is a logo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:37:56 -04:00
57cf0759c0
docs: Add logos to web page
...
Also, move docs/index.md to docs/_layouts/home.html. Add a
docs/_layouts/README file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 22:35:35 -04:00
85c01d4b6a
docs: Minor node changes to klipper logo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:42:40 -04:00
49b18a6be7
docs: Update logo so that edges overlap
...
Overlapping edges reduce the effects of anti-aliasing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:31:29 -04:00
9b960e63fb
docs: Add a Klipper logo
...
Signed-off-by: Jonne Kuusela <johnedwa@gmail.com>
Signed-off-by: Michael J Shephard <michael.j.shephard@gmail.com>
Signed-off-by: Thomas Herrmann <therrmann23@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-18 11:31:29 -04:00
6f34ba59cb
docs: Add an index page for the www.klipper3d.org website
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 22:00:35 -04:00
4739e28137
docs: Add a github pages html template
...
Add an html template so that each page has a navbar at the top and a
sidebar on the left with an auto-generated table of contents.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 20:55:41 -04:00
64e7235e48
docs: Rewrite the Overview.md - just list documents by category
...
Replace the Overview.md document description with a list of documents
and a brief description of their contents. The goal is to make it
easier for users to find information.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 20:45:00 -04:00
cb04e4c45d
docs: Fix alignment of tmc2208.svg
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-16 11:34:45 -04:00
c440c6b7aa
docs: Start of google pages _config.yml file
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-15 11:04:23 -04:00
e3df39245f
docs: Fixup github pages
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-14 22:41:23 -04:00
8a6d415745
Update CNAME
2019-04-14 21:25:54 -04:00
b90a04a5cf
Create CNAME
2019-04-14 21:21:14 -04:00
63f8d8cc79
Set theme jekyll-theme-leap-day
2019-04-14 21:17:52 -04:00
8bc9f39c58
docs: Avoid using .. in markdown links
...
Using .. in the markdown link can confuse some document processors.
Use an absolute link to github instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-14 21:12:21 -04:00
04adde9a02
docs: Update Installation.md to point to list of supported ARM mcus
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-06 18:47:02 -04:00
de124677b0
docs: Update BLTouch.md to refer to Probe_Calibrate.md for offset config
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 18:22:57 -04:00
9f9262cba8
docs: Minor wording changes to BLTouch.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 18:20:21 -04:00
54a2c5d58e
BLTouch: Use G90 in the BLTouch.md homing_override example
...
Reported by @sgtnoodle.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 17:49:58 -04:00
a5a6ae83ff
docs: Wrap BLTouch.md to 80 columns.
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 17:48:51 -04:00
6318bdc99b
docs: Note the python software dependency update in Config_Changes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 11:20:36 -04:00
0615ab5f89
docs: Note the use of bus enumerations in Config_Changes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:30:04 -04:00
be6b29fabf
sx1509: Convert code to use generic i2c bus support
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:29:30 -04:00
9bd3e80421
docs: Note that graphstats.py can produce different types of graphs
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-01 22:24:45 -04:00
2980c2e12c
docs: Minor wording change in MCU_Commands.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-01 22:04:56 -04:00
c30a6f2e6b
docs: Update Protocol documentation with enumerations
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-01 21:41:33 -04:00
b35e07ca2b
docs: STM32F0 benchmarks ( #1462 )
...
Signed-off-by: Eugene Krashtan <eug.krashtan@gmail.com>
2019-03-29 09:38:54 -04:00
c105adc80b
temperature_fan: Fix. Temperature fan min speed should be used ( #1405 )
...
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
2019-03-28 14:07:40 -04:00
c7330e07a4
stm32f0: Various fixes according to comment: ( #1453 )
...
* Copyright in log.c
* GPIO check completely removed
* generic/timer_irq added
* Change in doc section
Signed-off-by: Eugene Krashtan <eug.krashtan@gmail.com>
2019-03-28 10:21:51 -04:00
312cabc3f7
docs: Move benchmark information from Debugging.md to new Benchmarks.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-28 09:52:06 -04:00
de7444ca69
docs: Remove spurious executable flag from documents
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-24 12:17:12 -04:00
b79db3e3d6
docs: Documentation draft for STM32F0
...
Signed-off-by: Eugene Krashtan <Eugene.Krashtan@opensynergy.com>
2019-03-24 12:10:11 -04:00
9aadc3c7fa
docs: Also note that driver_VSENSE was removed from tmc2660 driver
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 22:40:42 -04:00
efab177645
docs: Note tmc2660 driver_HEND default change from 6 to 3
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:41:32 -04:00
0980b7e4ec
tmc2130: add SET_TMC_CURRENT and SET_TMC_FIELD commands ( #1419 )
...
Signed-off-by: Frank Kang <amblidex@outlook.com>
2019-03-22 20:37:03 -04:00
06c0463d44
Update sensorless homing documentation to disable second home
...
Signed-off-by: Frank Kang <amblidex@outlook.com>
2019-03-19 10:55:59 -04:00
b28e95ca1a
command: Always pass a string to the DECL_CONSTANT() macro
...
Make it clear that the name of the constant being defined is a string.
When the value being defined is also a string, use a new
DECL_CONSTANT_STR() macro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-17 19:38:18 -04:00
12f6513ba2
docs: Recommend OctoPi v0.16.0
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-11 22:13:04 -04:00
96c4e1c5a0
docs: Update atsam usb transfer benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 21:59:18 -04:00
d3f6dad853
controller_fan: Allow multiple controller_fan sections to be defined
...
It may be necessary to define multiple fans, so allow each config
section to be named.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 13:57:01 -04:00
5c0a2479be
screws_tilt_adjust: Add new screws_tilt_adjust tool ( #1367 )
...
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
2019-03-08 11:47:17 -05:00
563bc37073
tmc2130: Rename driver_BLANK_TIME_SELECT to driver_TBL
...
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:25:19 -05:00
89935c6831
docs: Update Config_Changes.md with tmc2660 changes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:08:24 -05:00
789379e95b
tmc2660: Add INIT_TMC and SET_TMC_FIELD gcodes
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-03-08 11:04:14 -05:00
d62a41b930
manual_stepper: Add support for moves with acceleration
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-03 13:38:10 -05:00
69491e2dab
filament_switch_sensor: update documentation
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-03-01 00:45:51 -05:00
c8d7e28a35
atsamd: Add support for programming SERCOM pins
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:40:44 -05:00
c039b33f2a
tmc2130: Add support for INIT_TMC command
...
Signed-off-by: Frank Kang <amblidex@outlook.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:24:39 -05:00
b40a04fb8d
docs: Update Installation document to emphasize the "stay connected" step
...
Move the OctoPrint "stay connected" during error configuration step to
its own paragraph. Hopefully this will make it less likely that users
skip this step.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-27 20:03:44 -05:00
88ebedcc63
docs: Update Installation document to suggest using /dev/serial/by-id/
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-27 19:58:09 -05:00
f7d8854587
bed_mesh: simplify configuration
...
The 'bed_shape' option has been removed. The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'. When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-02-25 13:34:14 -05:00
31987c7bcd
docs: Add a Manual_Probe.md document
...
Add information on calibrating the bed on traditional printers with a
Z endstop and bed screws.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-24 00:49:47 -05:00
80c8bd8b4d
bed_screws: Add a helper tool for leveling bed screws
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-24 00:49:47 -05:00
328bd89fc1
docs: Warn against using the TMC2208 in standalone mode
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-20 16:22:06 -05:00
276d5a1436
probe: Add PROBE_ACCURACY command
...
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-18 00:36:28 -05:00
82efed5e2a
docs: added an answer to the FAQ about detecting lost steps ( #1265 )
...
Signed-off-by: christian mock <cm@tahina.priv.at>
2019-02-17 22:35:58 -05:00
cc4ecef88b
mcp4018: Add initial support for the mcp4018 digipot
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-16 08:16:37 -05:00
0f674ef407
tsl1401cl_filament_width_sensor: Filament Width Sensor Support ( #1132 )
...
Support added for filament diameter sensor. Sample configuration parameters added to example-extras.cfg.
Signed-off-by: Mustafa YILDIZ <mydiz@hotmail.com>
2019-02-14 10:13:48 -05:00
c6d1d1bd8c
Merge pull request #1242 from john--/pr_generic_heater
...
Generic Heater Support
2019-02-14 10:08:26 -05:00
dd303ec4a9
docs: Try to make manual vs automatic probing more clear in DELTA_CALIBRATE
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-13 23:20:34 -05:00
6316b2c1b6
Generic Heater Support
...
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
2019-02-14 01:15:11 +00:00
5aa4fd2b4a
docs: Note MCP4728 in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 18:39:12 -05:00
2d7c3a84ee
manual_stepper: Add an "extras" module for manually controlling a stepper
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:38:13 -05:00
57e6acbc5c
docs: Add Bed_Level.md and Probe_Calibrate.md documents
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:20:32 -05:00
b0b9fc6f4a
probe: Use manual_probe helper when performing manual probes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:20:32 -05:00
35ea4a137d
probe: Add PROBE_CALIBRATE command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:20:32 -05:00
d14a53e160
manual_probe: Add a helper script for performing manual Z probing
...
Add MANUAL_PROBE and Z_ENDSTOP_CALIBRATE commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-12 13:20:32 -05:00
805e56008f
docs: Note command dispatch benchmark needs desktop class machine
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-11 16:35:03 -05:00
5ab6bcd1d7
docs: Report the actual SAMD51 3 stepper rate in the Features benchmark
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-11 12:57:44 -05:00
607461f7b6
docs: Update duet2 benchmarks
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2019-02-10 17:59:40 -05:00
faedc77621
docs: Fix typo in Protocol.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-10 11:53:56 -05:00
32e0d4d3ac
docs: Update atsam benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-07 13:24:03 -05:00
1f9208dc66
docs: Update benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-06 22:08:39 -05:00
5b9ce328e5
docs: Clarify FAQ item on running multiple instances of klippy
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-02-03 17:41:57 -05:00
c3e889a67c
docs: Add performance results for SAMD51
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-28 20:05:50 -05:00
893cbbab83
pause_resume: update documentation
...
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-01-28 11:23:52 -05:00
90827a88de
docs: Minor wording change to step_distance FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-27 16:52:16 -05:00
71ef715a88
docs: Expand FAQ on why step_distance is used
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-27 11:29:42 -05:00
b6ccd2682c
Kconfig: Move SERIAL_BAUD to src/Kconfig and show with LOW_LEVEL_OPTIONS
...
Move the definition of SERIAL_BAUD to the main src/Kconfig file. Only
show this as an option if the user selects the ability to configure
low-level options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-25 18:02:03 -05:00
15afcf69fe
docs: Improve the BLTouch documentation ( #1107 )
...
Signed-off-by Fred Sundvik <fsundvik@gmail.com>
2019-01-25 12:53:00 -05:00
76138fde5c
docs: Add a FAQ item for "Do I have to use OctoPrint?"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-21 12:01:24 -05:00
8c5a94f49f
docs: Sort command dispatch table by transfer rate
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-20 14:17:08 -05:00
f0ac5c378f
docs: Update Debugging document with SAM3X8E usb transfer benchmark
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-20 00:57:48 -05:00
33f5b5f285
docs: Update Code_Overview.md with removal of printer_state() callback
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-08 11:34:09 -05:00
e26d1a3567
i2ccmds: Pass the i2c address as a 7-bit number (0-127)
...
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 20:00:44 -05:00
f2f54290e8
docs: Add a new Config_Changes.md document
...
Add a document to track non-backwards compatible changes to the
printer config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 20:00:44 -05:00
549e682069
docs: Add sam4s8c benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 19:43:56 -05:00
70bbdf9334
sam3: Rename src/sam3x8e to src/sam3
...
This is in preparation for merging sam3 and sam4 code into one
directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 19:33:26 -05:00
c8e04274ad
docs: Add a FAQ item for "multiple instances of klipper on the same machine"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 13:59:52 -05:00
d015209388
docs: Add guide for sensorless homing ( #1004 )
...
Signed-off-by: Yannic Schroeder <schroeder@ibr.cs.tu-bs.de>
2019-01-07 10:39:16 -05:00
28e68075c8
docs: Suggest checking for bad wires in "lost communications" faq entry
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 10:28:25 -05:00
186d815469
docs: Documentation/FAQ, Raspii voltage
...
Add note that `under power` may be related to communication issues.
Signed-off-by: Wilfried Goesgens <dothebart@citadel.org>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-05 20:59:12 -05:00
df42887193
docs: Bltouch documentation ( #1073 )
...
Add documentation on howto configure the BL-Touch device with
Klipper. A second paragraph addresses possible issues with BL-Touches
Signed-off-by: Wilfried Goesgens <dothebart@citadel.org>
2019-01-05 20:24:35 -05:00
59e9b6562f
respond: An extra for sending messages to the printer host. ( #1053 )
...
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host ). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
2019-01-02 17:45:35 -05:00
d7b0a7e961
docs: Add a FAQ item on how to cancel a "wait for temperature" request
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-20 16:25:58 -05:00
566488dc01
docs: Add a FAQ item on Raspberry Pi reboots
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-20 16:25:58 -05:00
e4dac1039d
docs: Update release notes for v0.7.0 release
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-20 09:15:24 -05:00
e0b2d7c51d
bltouch: Add a BLTOUCH_DEBUG command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-12-03 22:52:32 -05:00
e505ab0df1
samd21: Add support for flashing an application via the bossac tool
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-30 22:22:42 -05:00
bb41765714
docs: Minor update to Code_Overview.md with further kinematics info
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-17 14:56:46 -05:00
cd1e669306
docs: Fix typo in command dispatch benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-16 20:38:30 -05:00
64a1837fec
docs: Round pru command parsing benchmark
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-16 20:31:41 -05:00
c349863988
docs: Add information on command parsing benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-16 20:21:05 -05:00
52fa91fb9a
docs: Update benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-16 18:59:55 -05:00
f973886dac
docs: Minor rewording in Endstop_Phase.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-14 09:46:21 -05:00
e541466591
servo: This patch create ability to enable/disable attached servo. ( #880 )
...
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.
Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]
For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo
This patch add one option to servo configuration:
enable: <False/True> # default True
It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.
Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
2018-11-14 09:38:09 -05:00
31730fa031
docs: Minor wording change to Endstop_Phase.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-13 18:44:33 -05:00
c55842b428
docs: Note when endstop phases are useful in Endstop_Phase.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-13 18:36:00 -05:00
8d4f7db66e
docs: Fix typo in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-13 14:41:51 -05:00
097e6c524b
docs: Fix link in FAQ document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-13 14:40:35 -05:00
5f9ce32fae
docs: Be more clear that a baud of 250000 is recommended
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-11-13 14:06:27 -05:00
c4058f71fb
docs: Clarify M109/M190 in G-Code documentation
...
Signed-off-by: Lucas Fink <software@lfcode.ca>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-28 14:22:30 -04:00
057acb07b7
docs: Add a Slicers.md document
...
Add some information on configuring a slicer for use with Klipper.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-28 10:47:32 -04:00
47e45ab391
docs: Note the use of gcode_macro in G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-28 10:38:03 -04:00
a33792f07e
util: Fix versioning when gitdir is absent ( #809 )
...
The gitdir previously could be absent and produce a version of "" in
spite of checks for it. Fixed.
Parent directories with shlex-interpreted characters in their names
could be misinterpreted. Removed shlex parsing.
Packagers may want to remove the git history to slim down the package
size, so add an option for using a file 'version' in the klippy
directory to set version without using git.
Signed-Off-By: Lucas Fink <software@lfcode.ca>
2018-10-27 10:44:38 -04:00
a7c8476e98
docs: Update pressure advance doc to note it only impacts the extruder
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-25 19:09:47 -04:00
3d7e8fa5ec
docs: Note impact of warping during pressure advance tuning
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-25 12:10:47 -04:00
ca7dd8bfd4
docs: Update Pressure_Advance.md - don't set square_corner_velocity=0
...
Setting the square corner velocity to zero would cause stuttering
during the test if a bed mesh is in effect. It's possible to get the
desired effect by reducing the square corner velocity and setting the
pressure advance lookahead time instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-25 11:43:03 -04:00
b6bf455155
tmc2660: Add endstop phase detection functionality to TMC2660 extra ( #816 )
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-10-24 16:01:12 -04:00
04a12ec9bd
docs: Update stm32f1.md - usb is now supported.
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-22 13:22:58 -04:00
e4bb90a1ca
bed_mesh: Do not automatically run G28 on BED_MESH_CALIBRATE / BED_MESH_MAP
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-22 11:26:01 -04:00
925562cfb1
delta_calibrate: Do not automatically run G28 on DELTA_CALIBRATE
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-22 11:26:01 -04:00
ca04caa42c
docs: Fix SAM4E8E benchmark test revision
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-22 11:21:43 -04:00
2b81b2935c
docs: Update SAM4E8E benchmarks
...
New benchmark numbers reported by @FHeilmann.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-22 11:18:55 -04:00
b903f84c80
docs: Replace get_status example with get_clock in Protocol.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-20 11:53:32 -04:00
530a37196c
docs: Update LPC176x benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-18 09:55:02 -04:00
0079311b0b
docs: Add an Endstop_Phase.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-16 13:09:49 -04:00
1e71909d02
endstop_phase: Add support for an ENDSTOP_PHASE_CALIBRATE command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-16 13:09:49 -04:00
f5c99c1dec
docs: Update benchmarks for Arduino Due
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-13 11:57:13 -04:00
aa693fbdc1
docs: Updates to stm32f103 benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-11 10:57:24 -04:00
75fa74313c
stm32f1: Add support for building with bootloader support
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-11 10:50:51 -04:00
bc5e961d73
stm32f1: Initial support for serial over USB
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-11 10:50:51 -04:00
1e07be4db4
docs: Add a "Lost communication with MCU" section to the FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-09 11:22:28 -04:00
852d1666bb
docs: Fix typo in BED_MESH_PROFILE description in G-Codes.md
...
Reported by @fiveNinePlusR
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-04 19:01:18 -04:00
b261d31ec5
bed_mesh: Add ability to save mesh state to persistent memory
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-10-02 16:26:35 -04:00
5c267e4f69
docs: Update Features.md document with tmc2660 support
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-02 14:07:33 -04:00
33887b8c39
probe: Support manual probing at runtime
...
Don't require the config file to specify manual probing. Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-10-01 11:12:30 -04:00
4b5db04f78
docs: Add Delta_Calibrate.md guide with "enhanced delta calibration"
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-25 13:48:46 -04:00
1165c0c9c5
docs: Additional images for enhanced calibration procedure reference ( #639 )
...
Signed-off-by: Charles Galant <cgalant@cogwheel.net>
2018-09-25 13:48:46 -04:00
0b2c89ecaf
delta_calibrate: Initial support for enhanced delta calibration
...
Add support for an enhanced delta calibration routine that performs XY
dimension calibration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-25 13:48:46 -04:00
5a1b2d61ae
pid_calibrate: Support saving calibration data via SAVE_CONFIG
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-25 13:48:46 -04:00
531134f092
configfile: Add support for rewriting the printer config file
...
Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-25 13:48:46 -04:00
3d4ee9e962
docs: Add stm32f1.md link to Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-20 20:11:04 -04:00
174754299a
heater: Add new TURN_OFF_HEATERS command
...
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-18 16:01:07 -04:00
094b9de69e
gcode: Send proactive state messages
...
Send a g-code info message on printer state changes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-12 21:31:27 -04:00
f15cd62587
docs: Update Pressure_Advance.md document
...
Update the document to recommend tuning with decreased acceleration
and with square_corner_velocity disabled. Using this approach makes it
possible to test with significantly higher pressure advance values.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-11 12:00:43 -04:00
c8dc47b162
docs: Note digipot support in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-03 21:10:53 -04:00
ac3aa097fb
docs: Features.md updates
...
Add information on new features in Klipper.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-09-03 20:55:53 -04:00
480415d2e8
docs: Update Bootloaders.md with AVR lfuse hints
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 12:34:37 -04:00
a5189f7c25
docs: Add some notes to Bootloaders.md on using the atmega168
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 12:08:55 -04:00
ee67715e2b
docs: Fix link in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 09:16:27 -04:00
28fe6a5df0
docs: Update SAMD21 flashing information in Bootloaders.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 09:07:27 -04:00
9b56c4f780
docs: Update Bootloaders.md with updated bossac info for sam3x8e
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-27 08:54:43 -04:00
96acfdc6d2
docs: Minor rewording of Marlin pin number section of FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-26 23:06:32 -04:00
a27e82aef3
docs: Add a section to the FAQ on translating Marlin pin numbers
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-24 21:43:53 -04:00
a8a912fbb5
docs: Update sam4e8e docs and benchmarks ( #562 )
...
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-08-22 19:17:43 -04:00
868a1f951b
docs: Add Mesh Bed Leveling to G-Codes.md
...
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2018-08-17 09:22:55 -04:00
be3131de3e
docs: Update Config_checks.md to use STEPPER_BUZZ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-09 13:46:07 -04:00
3f59c3dd48
docs: Add a Bootloaders.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-08 20:47:04 -04:00
71063fe500
docs: Warn about possible pin conflicts in benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-08 13:52:08 -04:00
cbf019a468
docs: It's difficult to estimate real-world usage from the benchmarks
...
Remove the prediction on real-world usage as it's not really practical
to make a prediction.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-08 13:39:29 -04:00
fbec3ebb63
docs: Add benchmarking details to docs/Debugging.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-08 13:28:08 -04:00
64e6d85898
sam4e8e: Add the SAM4e8e port
...
This can be flashed to e.g. the duet wifi using bossac. It requires a
later version as is currently included in the klipper repo (1.8
vs. 1.2). Comms are currently via UART0 only, USB serial is still TBD
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
2018-08-08 10:44:49 -04:00
a5d27c55e1
docs: Update perf benchmarks with SAMD21 results
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-07 00:03:42 -04:00
cd24d61515
docs: Minor change to wording of junction speeds
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-03 15:48:07 -04:00
1fefd695de
docs: Note square corner velocity in lookahead description
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-03 15:43:46 -04:00
f2d232ef77
force_move: Provide defaults for SET_KINEMATIC_POSITION parameters
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-08-02 08:58:18 -04:00
09a64d24f1
docs: Remove the Todo.md file
...
The Todo.md file has gotten stale, and it is no longer an effective
mechanism for tracking changes. Remove it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-26 12:51:01 -04:00
c0c892d524
force_move: Add support for FORCE_MOVE command
...
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-26 12:44:07 -04:00
0025fbf10d
toolhead: Replace junction_deviation with square_corner_velocity
...
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-16 10:32:43 -04:00
f60b0093b7
docs: Add a section with micro-controller porting tips to Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-11 14:40:39 -04:00
4125e176b7
docs: Expand on why it is important to provide the log in Contact.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-08 20:30:35 -04:00
fa9b321991
docs: Update main documentation to not Smoothieboard support
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-08 11:01:54 -04:00
f3ac1a2306
docs: Add M206 and M119 to G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-08 10:23:44 -04:00
b4f03e8363
docs: Add display g-code commands to docs/G-Codes.md
...
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-08 10:12:23 -04:00
5c7c8c984b
stm32f1: add SPI support
...
Add basic SPI support and associated documentation.
v2: remove baud rate check, fix baud rate calculations
v3: finish transaction with BSY check, disable SPI when not in use
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
2018-07-07 11:05:33 -04:00
7e9ee6aef7
docs: Minor updates to Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-03 13:33:48 -04:00
e08bb4f196
docs: Fix whitespace error in stm32f1.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-07-01 09:41:35 -04:00
b41770caa6
tmc2130: Add a DUMP_TMC helper command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-30 19:01:56 -04:00
eb02043943
stm32f1: add port documentation ( #425 )
...
Fixes #412 .
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
2018-06-27 18:21:23 -04:00
d651851567
pru: Disable ADC reading directly from the PRU
...
The PRU code size has grown too close to the maximum - remove the ADC
code to reduce its overall size. (On the beaglebone, the Linux
process can, and typically does, do the ADC reading.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-27 12:10:25 -04:00
890298d34d
itersolve: Support setting the stepper position via a cartesian coordinate
...
Add support for an itersolve_set_position() function that sets a
stepper position from a cartesian coordinate. This eliminates the
need for both the python and C code to be able to translate from a
cartesian coordinate to a stepper position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-22 14:09:01 -04:00
0216201cb6
delta: Rename get_position() to calc_position()
...
Calculating the cartesian position from the stepper positions can be
complex and cpu intensive, so rename it to calc_position() to be more
descriptive.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-22 14:09:01 -04:00
3ac9fc6e63
docs: Update documentation with iterative solver changes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-20 09:26:10 -04:00
efe63d5efe
toolhead: Add support for the M204 command
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-15 12:05:45 -04:00
2c4ca88887
docs: Update documentation to note use of /dev/serial/by-path/
...
When using multiple micro-controllers it may be necessary to use an id
from /dev/serial/by-path/ instead of /dev/serial/by-id/. Also,
emphasize that in config/example-multi-mcu.cfg.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-06-01 17:22:03 -04:00
b93fd5b1b5
basecmd: Rename get_status to get_clock
...
Change the get_status command to get_clock. Don't report the shutdown
status in the new get_clock command.
The primary purpose of this change is to force the host code to report
a firmware version mismatch with older firmwares as recent changes
(namely the ordering of message block acks) have subtle
incompatibilities if different host/mcu code is used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-29 10:57:29 -04:00
c9dfdf21e5
docs: Remove lpc176x item from Todo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 13:56:54 -04:00
83d3c17280
docs: Add LPC1768 benchmarks to Features.md document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-25 11:52:13 -04:00
ee4f37fe0c
stepper: Add STEPPER_BUZZ command
...
Add a new command that can help diagnose stepper motor connectivity.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-24 09:49:17 -04:00
e50c2aa38d
docs: Remove "touch panel" item from Todo document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-23 22:31:45 -04:00
3025638b9b
z_tilt: Add support for Z_TILT_ADJUST
...
Add new module to support independent adjustments to multiple Z
steppers to account for bed tilt.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-22 22:23:44 -04:00
42ca985bef
docs: Add reference to homing_override in FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-20 19:33:54 -04:00
2ab47cd20c
extruder: Fix SET_PRESSURE_ADVANCE so that it works with multiple extruders
...
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-20 12:52:19 -04:00
22487d95e9
spicmds: Rework SPI message transmission
...
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-07 09:10:34 -04:00
cd9e21e3aa
FAQ: Add item on TMC2208 being disabled in the middle of a print
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-05-05 13:06:55 -04:00
15248706ae
chelper: Move the host C code to a new klippy/chelper/ directory
...
Move the C code out of the main klippy/ directory and into its own
directory. This reduces the clutter in the main klippy directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-30 11:44:53 -04:00
22c49a7c3f
docs: Improve FAQ update software entry (use make menuconfig ; make clean)
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-25 10:29:55 -04:00
3ef7c00b73
docs: Fix internal link description in Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-23 18:23:39 -04:00
bdd26e421b
toolhead: Add a SET_VELOCITY_LIMIT command
...
Add a command to adjust the maximum velocity, acceleration, and
junction deviation parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-20 22:36:05 -04:00
6d03dee104
gcode: Add a SET_GCODE_OFFSET command
...
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-20 20:04:41 -04:00
832c0bc017
docs: Add more hints to use /dev/by-id/ for the serial device
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-20 11:57:49 -04:00
606222da5b
docs: Add STM32F103 benchmarks to the Features document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-20 11:19:37 -04:00
c539fed8bb
docs: Add additional information to FAQ on heater checks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-09 22:00:26 -04:00
97f30765a1
docs: Update installation document for OctoPrint 1.3.7
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-04-09 11:39:36 -04:00
a301713361
extruder: Add SET_PRESSURE_ADVANCE command.
...
Signed-off-by: Michael Barbour <barbour.michael.0@gmail.com>
2018-04-03 00:00:41 -04:00
bee179eab4
docs: Update release notes for v0.6.0 release
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-31 14:04:39 -04:00
039bb9f10f
docs: Add Patreon link to FAQ page
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-31 13:55:41 -04:00
a6553538e6
docs: Update G-Codes.md with recent output_pin changes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-28 15:11:10 -04:00
019666a6f6
docs: Add a section on adding new host modules to Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-28 13:12:41 -04:00
f5c67baac2
docs: Recommend running PID_CALIBRATE in Config_checks.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-18 12:43:41 -04:00
973ef97143
pid_calibrate: Move PID calibration logic from heater.py to new file
...
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-18 12:02:30 -04:00
5c05a24947
docs: Fix typo in M220 description in G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-18 11:44:56 -04:00
451f7d5672
gcode: Position returned by M114 should be relative to last G92
...
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-15 20:00:51 -04:00
ef820d98f6
docs: Add "will heaters be turned off on a crash" item to FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-13 11:36:45 -04:00
5208fc38ed
verify_heater: Add initial support for verifying heaters and sensors
...
Add runtime checks to heaters and temperature sensors to check for
possible hardware faults.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-11 00:49:11 -05:00
e53a589ac3
docs: Add SET_DUAL_CARRIAGE command to G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-10 20:22:13 -05:00
ddcf9a7ff7
docs: Add Tx command to G-Codes.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-08 14:40:26 -05:00
05ec7ca7ff
docs: Add a G-Codes.md file with the list of available commands
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-08 14:11:20 -05:00
82a65e9f4a
docs: Note the use of the virtual_sdcard feature
...
Note that virtual_sdcard helps on slower machines.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-03-02 11:28:01 -05:00
5e8aaed41f
docs: Add tips for porting to new kinematics to Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-02-17 13:48:53 -05:00
268d1cb27c
docs: Update Config_checks.md
...
Navigation should be to the temperature tab to find the Tool temperature box.
Signed-off-by: Dave Bacon <drb.github@mrbacon.com>
2018-02-07 22:24:32 -05:00
7d3600f918
docs: Add github issue template
...
Add an issue template requesting the klippy log file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-31 14:30:05 -05:00
650d55d7b2
docs: Remove bed level probe from todo
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-28 20:36:04 -05:00
08444a8b89
docs: Try to make the klippy.log bug reporting more clear
...
Emphasize that the log file needs to be attached to the issue.
Encourage M112 to be issued on every bug report.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-21 13:08:31 -05:00
054cbbe094
docs: Add a FAQ item on steps to upgrade the software
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-12 18:38:49 -05:00
f1222565b8
docs: Update Debugging.md with information on logextract
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-11 13:48:40 -05:00
df6528715e
stepper: Automatically detect and handle shared stepper enable lines
...
It's common for multiple steppers to use the same stepper enable
line. Detect this and only create a single digital_out oid on the
micro-controller.
Also, prohibit any other pin from being used multiple times in the
config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-10 19:10:26 -05:00
0cf06ee69a
docs: Note pressure_advance over 0.20 is unlikely to improve quality
...
Update the pressure advance tuning document to note that 0.20 is
likely the ceiling of a useful pressure advance setting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-08 11:07:26 -05:00
83e9e92b9a
docs: Add a table of contents to the FAQ
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-05 11:42:00 -05:00
29c83cec22
docs: Update installation document with pointers to FAQ
...
Add some pointers to the FAQ for common pitfalls during installation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-04 13:29:17 -05:00
e4129a7e53
docs: Minor update to square.scad
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2018-01-02 21:56:29 -05:00
1bdebeaebf
docs: Add an initial configuration checklist document
...
Provide a document with basic steps that a user can run to verify that
the pins in the configuration file are set correctly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-26 20:54:37 -05:00
479772ca00
docs: Add a CONTRIBUTING document
...
Add an initial document detailing best practices for contributing to
the document. Add the "developer certificate of origin" document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-24 12:33:01 -05:00
522093ef00
docs: Offer alternatives to ssh/scp/sftp
...
Try to make the Installation document more friendly to users not
familiar with the Linux command-line. Offer some hints on how to
obtain ssh and how to edit the config file remotely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-21 17:34:35 -05:00
9a4425c85a
docs: Update square test print to contain notches on inside of square
...
Add additional notches and move them to the inside of the square where
they will not impact the outside perimeter test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-17 12:18:25 -05:00
8944e2104d
docs: Add FAQ item on AVR watchdog restart failures
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-11 18:17:14 -05:00
319221ee23
docs: Provide additional information on "make flash" failures
...
Add some additional information on "make flash" problems.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-12-11 17:33:29 -05:00
37788c1e55
docs: Add a FAQ document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-11-30 15:19:40 -05:00
6bbb84326d
docs: Add further details on how to report a bug
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-11-21 18:27:22 -05:00
fc0e016a6d
docs: Note version 0.5.0 release
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-25 11:27:20 -04:00
3d78a99758
docs: Update Installation document to recommend latest octoprint version
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-25 10:44:49 -04:00
db97f36631
gpiocmds: Allow the start value for a pin to differ from the default_value
...
Allow the start value to be different from the default/shutdown value
for the pin. This will be useful for "heater fans" that should
startup in the off state, and transition to full on in a shutdown
state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-12 11:59:27 -04:00
3b9b4e4d6f
endstop: Eliminate end_stop_set_oversample command
...
Pass the sample_ticks and sample_count parameters directly in the
end_stop_home command instead. This simplifies the code.
Also, simplify calculation of next wakeup time in
end_stop_oversample_event().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-12 11:59:27 -04:00
d3eb148cfa
docs: Point to beaglebone.md from the main installation document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-11 21:03:13 -04:00
00d541b767
docs: Octoprint should not run at a higher priority than Klipper on beaglebone
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-11 20:23:58 -04:00
6a2eaeae40
docs: Add mailing list to Contact.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-10 14:24:04 -04:00
ce7cc798dc
docs: Add Contact.md file with developer contact information
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-10 12:43:44 -04:00
5c982c90f3
docs: Add a notch to the default square.stl test object
...
Place a small notch on one side of the square. The notch provides
interesting information on the extruder performance, and it makes it
easier to compare with previous prints of the object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-03 22:08:36 -04:00
459695e9d7
docs: Remove items from Todo.md
...
Several items were recently implemented. Remove the "cubic vs
quadratic" item as investigations into cubic compression weren't
promising.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-10-01 19:34:00 -04:00
4c40b50fb5
docs: Add a section on time handling to Code_Overview.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-27 15:11:15 -04:00
a0f0911a95
docs: Reword performance paragraph in Features.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-27 13:59:47 -04:00
ead99cf647
docs: Update Features.md document for multiple micro-controllers
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-26 22:27:25 -04:00
3b4088c23f
chipmisc: Add support for Replicape board
...
Add support for configuring and controlling the hardware specific to
the revision "B3" Replicape board.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-20 13:18:07 -04:00
f662445766
stepcompress: Implement print time to clock conversion in C code
...
Implement the conversion from print_time to the local mcu's clock
within the C code. This simplifies the python code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-19 17:25:43 -04:00
8d0ef49e8f
toolhead: Permit look-ahead between Z moves
...
Extend the look-ahead mechanism to work between moves that contain Z
movement. This improves Klipper's handling of g-code produced in
"vase mode".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-09-03 15:46:48 -04:00
60c77fff06
docs: Update Code_Overview.md - step compress queue no longer 64 bit
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-31 10:07:17 -04:00
80dc1dfcc1
docs: Remove documentation for "custom" command blocks
...
It should no longer be necessary to configure "custom" commands during
mcu setup. The ad5206 and static_digital_output config sections
should provide similar functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-26 18:27:21 -04:00
0adea120cd
pru: Compile the irq_poll() function with -O2 optimization
...
Compile the PRU binary with -Os optimization, but request that the
timer dispatch code be compiled with -O2 optimization. This improves
the performance of timers slightly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-15 11:05:30 -04:00
71bb7acb8e
pru: Compile with -Os instead of -O2
...
The gcc -Os option significantly reduces the size of the PRU binary
and it has little impact on performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-14 21:08:28 -04:00
f3da473285
docs: Update Code_Overview.md with PRU and command_dispatch() changes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-11 12:06:19 -04:00
f0f4ab7abe
docs: Update benchmarks in Features document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-08-11 11:40:54 -04:00
2ee42997e4
docs: Update Kinematics.md with regards to stepper torque limits
...
It is not necessary to limit stepper acceleration - only the limiting
of stepper torque is important.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-19 19:09:14 -04:00
17a3e25036
docs: Improve description of delta stepper acceleration limits
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-19 14:14:01 -04:00
2d173f51b1
pru: Add documentation and install scripts for running on the PRU
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-07-05 14:21:32 -04:00
3af87e1c42
avr: Add SIMULAVR build option; don't show WATCHDOG or SERIAL_BAUD_U2X
...
Add a CONFIG_SIMULAVR option to the Kbuild menus and don't directly
prompt users for CONFIG_WATCHDOG or CONFIG_SERIAL_BAUD_U2X. The only
reason to disable these options would be if one were running on
simulavr. This simplifies the user visible menu options.
Also, only show CONFIG_CLEAR_PRESCALER for at90usb1286 chips.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-28 11:04:59 -04:00
f91a49c65d
docs: Note how to handle odd corner in Pressure_Advance.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-25 13:39:16 -04:00
4b8ad3fc03
docs: Add a prerequisites section to Pressure_advance.md
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-22 12:32:20 -04:00
e8aabbb40b
docs: Add Todo item for supporting custom fan and pin config sections
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-22 11:55:41 -04:00
5c4cc0d646
pwmcmds: Export the maximum PWM value
...
Instead of assuming the maximum PWM value is 255, export a constant
from the firmware to the host with the maximum value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-15 14:02:59 -04:00
8f1d0c2a7c
docs: Note version 0.4.0 release
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-03 14:32:36 -04:00
02549c9299
docs: Make it clear a RESTART is likely needed in Installation document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-03 11:15:27 -04:00
b5062a07d1
docs: Recommend users stop klipper before flashing the micro-controller
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-01 12:08:45 -04:00
4112007314
docs: Reword XY+Z delta moves in Kinematics
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-01 11:58:32 -04:00
a3162b17d9
docs: Use only single space at start of new sentence
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-01 11:58:32 -04:00
e177d4f70d
docs: Reword smoothed look-ahead description in Kinematics
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-05-01 11:58:32 -04:00
631b0e6c37
docs: Improve wording of slow lookahead description
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 16:05:26 -04:00
a7f339ad1c
docs: Improve documentation for those starting in docs/
...
Those that reach Klipper via github may jump directly to the docs/
directory in search of documentation. Add README.md and rework
Overview.md with that in mind.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 16:05:26 -04:00
c1c0b2dd38
docs: Avoid using "firmware" in the documentation
...
The term "firmware" is ambiguous - it could refer to the entire
project (host and micro-controller software) or to just the
micro-controller software. Avoid the term in the documentation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 15:59:33 -04:00
d7a1111955
docs: Add backticks around commands in Firmware Commands
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 12:10:38 -04:00
d73340474b
docs: Use "look-ahead" instead of "lookahead" in Code Overview
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 12:02:15 -04:00
4f7237de44
docs: Update Firmware Commands document with an integer example
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 12:00:10 -04:00
4096745a58
docs: Use a markdown link to docs/prints/square.stl
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 12:00:09 -04:00
a97e074022
docs: Kinematics document image updates
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 12:00:09 -04:00
917c6aa94a
docs: Todo updates
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-27 09:52:38 -04:00
56d4422d31
docs: Reword alternate linux machine in installation instructions
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-24 09:39:40 -04:00
e507848a8f
docs: Remove "experimental" from descriptions
...
The Klipper software has progressed to the point where it does not
need to be described as "experimental" software.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-24 09:31:39 -04:00
70599667cb
docs: Installation updates
...
Recommend using 'make flash' and clean up the octoprint instructions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-24 09:21:21 -04:00
1878da228d
build: Add workaround to suppress broken avr-gcc "misspelled" warnings
...
Detect avr gcc v4.8.1 and then disable warnings during the klipper.o
linking to suppress bogus "misspelled signal handler" warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-24 08:54:10 -04:00
ec805aee2e
scripts: Add octopi installation scripts
...
Add a system startup script so that Klipper can automatically start at
boot time. Create an installation script that will install the system
dependencies and the startup script.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-21 10:14:27 -04:00
167b18b58f
gcode: Ignore M21 command
...
No need to recommend users disable "SD card support" in octoprint -
instead, just ignore the M21 command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-20 10:11:10 -04:00
19ffaa9ff0
docs: Reword parts of the pressure advance kinematics description.
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-19 20:48:23 -04:00
0f5167a407
docs: Misc image updates
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-19 19:55:50 -04:00
563ab5caa5
docs: Add info on delta acceleration limits
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-19 19:54:48 -04:00
db5b5f121c
docs: Add initial Pressure Advance tuning document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-19 16:02:11 -04:00
1f417a8441
docs: Update Todo - initial kinematic document written
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-15 22:59:34 -04:00
b74b09ea7a
docs: Updates to Features document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-15 22:52:36 -04:00
2cce67ad84
docs: Add initial Kinematics document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-15 22:26:03 -04:00
839725e3c5
queuelogger: Automatically roll log file
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-14 09:58:34 -04:00
a3a45b5037
docs: Update Todo - RPi power over USB now implemented
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-13 14:18:48 -04:00
dc645d76b4
docs: Reword and reformat parts of move code flow in Code_Overview
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-13 14:08:02 -04:00
daff83ee9a
hub-ctrl: Add support for micro-controller reset via RPi usb power toggling
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-13 13:20:13 -04:00
8491b1f86a
docs: Update Features document with latest performance benchmarks
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-11 13:53:33 -04:00
a7b4d70cc6
docs: Add documentation on how to run the graphstats.py script
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-11 13:41:11 -04:00
050008f3c8
docs: Update Debugging.md file with python virtual env setup
...
Direct readers to the main Installation file to setup the python
virtual environment and remove the outdated instructions in the
Debugging file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-11 12:49:12 -04:00
70e53cb080
docs: Update Firmware_Commands with recent end stop changes
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-11 12:36:29 -04:00
ca6245e974
docs: Update Code Overview document with code flow for a typical move
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-10 22:10:49 -04:00
49bdc6fbd1
corexy: Initial corexy kinematic implementation
...
Add initial support for corexy kinematics.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-04-03 17:27:14 -04:00
384c853a39
docs: Update benchmark results in Features document
...
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-03-31 17:50:36 -04:00
6d05dd07f5
sched: Move timer dispatch loop to board code
...
Rename sched_timer_kick() to sched_timer_dispatch() and move its loop
into its callers in the board code. This eliminates the need to
export timer_try_set_next() from the board code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2017-03-30 11:24:42 -04:00
Kevin O'Connor