Introduce a new step_gen_time variable for flush_step_generation().
This allows need_flush_time to be set to future times without
interfering with flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Call toolhead.note_kinematic_activity() on each pin update to ensure
that those updates will be flushed properly.
This fixes "Timer too close" errors on SET_PIN commands that are
issued when the toolhead is idle.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Track a "NeedPrime" queue state instead of the "Flushed" state, and
continue running the background flushing timer as long as there may be
data in any of the move queues.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename last_kin_move_time to need_flush_time and rename
force_flush_time to last_flush_time to improve variable name clarity.
Move low-level flushing to new _advance_flush_time() so that it is
possible to flush the queues without needing to advance print_time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Simplify the code by introducing a separate lookahead priming flush
timer. After this change, the flush_timer is not active in any of the
special queuing states.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Clarify the internal naming to make a more clear distinction between
"stalling" (input not coming fast enough) and "pausing" (the need to
hold up reading of input to avoid buffering too far into the future).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
These internal low-level config parameters were never documented.
Going forward, developers may modify them by altering the internal
settings in toolhead.py.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Note that the max_accel parameter is the actual acceleration used in
most movements.
Note that the accel/velocity limits can be changed using the
SET_VELOCITY_LIMIT command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The set_register() code may block, and it therefore may be possible
that the loop in _init_registers() could occur in parallel with other
updates. That could result in a "OrderedDict mutated during
iteration" error.
Avoid the error by querying the latest value during each iteration of
the loop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible to build and configure tmc5160 drivers with external
mosfets that support more than 3 amps. The actual maximum for tmc5160
drivers is dependent on how the board is wired and the mosfets used.
Increase the error check to 10 amps. This error checking is primarily
intended to catch "obvious misconfigurations" (eg, specifying
milli-amps instead of amps), and the new value of 10 amps should
suffice for this task.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extends the BMxx80 category with support for the older BMP180 sensor, providing temperature and humidity output.
Signed-off-by: VAXXi Popescu <github@vaxxi.net>
The output_pin module is only capable of updating an output pin at
most once every 100ms. Add a new pwm_tool module that is capable of
queuing updates in the micro-controller and thus allowing for much
higher update rates.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In testing with a user on Discord we discovered the sensorless homing thresholds were out of line with what Sovol ships with Marlin. This aligns with their settings.
Signed-off-by: Herb McNew <herb.mcnew@gmail.com>
New configuration for the Sovol SV06 Plus
Initial pass at adding a printer configuration for the Sovol SV06
Plus based on the existing Sovol SV06 config. Updated for the larger
build volume, added filament runout sensor, and removed any references
to the LCD screen since the stock screen doesn't work with Klipper.
Signed-off-by: Herb McNew <herb.mcnew@gmail.com>
Try to make it more clear that Discord is not Discourse, as the two
similarly sounding services are often confused by users unfamiliar
with them.
The Klipper Discourse and Klipper Discord are available for many
topics related to Klipper - reword some sections to make their use
more open.
Avoid referring to the Klipper github repo in this Contact document as
we no longer use Klipper github issues at all.
Remove the table of contents as it is largely redundant for the
document.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use two different files for the Octopus Pro and Octopus (non-Pro).
The configs are the same in practice, but the difference in version
and naming can lead to confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit 6749985302.
A defect was found in the above commit (the input shaper code calls
note_step_generateion_scan_time() for many steppers, so the
input_shaper class can't be used as the index).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In the "Verify endstops" section there is an example of adding an
exclamation point to the pin definition to invert its logic. I
believe the intention in the example is to keep the hardware pull-up
^ and follow it with ! to invert the pin logic, but the ! is missing.
Signed-off-by: Tom Dunn <thomas.dunn@gmail.com>
The atsam USB hardware only requires that the ACM endpoint be endpoint
3. As of commit 11828387 the atsam chips can therefore use the
default USB endpoints.
This will allow CAN bridge support for the SAME70 to function
(upstream host driver has hardcoded endpoints).
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Kevin O'Connor