Minor fix. The screw labels "back left" and "back right"
where swapped in [screws_tilt_adjust] section.
Signed-off-by: Frank Roth <developer@freakydu.de>
Works for unmodified stock Artillery Sidewinder X2,
year 2022 with Artillery Ruby v1.2 mainboard.
All by default connected things are working fine.
Build firmware with architecture STM32F401 with "No bootloader".
Other settings keep ther defaults
Signed-off-by: Frank Roth <developer@freakydu.de>
Corrected the build instructions for the TH3D EZBoard V2 to include the command to convert Klipper.elf to a SREC bin format named firmware.bin. The SREC format is required for the bootloader installed on the board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
* Update printer-anycubic-vyper-2021.cfg
better pause and end print, beeper support, mroe accurate value.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
delete unnecessary gcode
* Update printer-anycubic-vyper-2021.cfg
remove unneccessary part.
* Update printer-anycubic-vyper-2021.cfg
* Update printer-anycubic-vyper-2021.cfg
according to https://www.klipper3d.org/Example_Configs.html point 7f
delete field values that are set to their default value
* Update printer-anycubic-vyper-2021.cfg
small change
* Update printer-anycubic-vyper-2021.cfg
As found on discord bt user David Carey.
uart_address for y and z are swapped. Discovered while setting up sensorless homing.
Signed off by: James Hartley <james@hartleyns.com>
Added a SET_DIGIPOT command to the mcp4018 implementation.
Previously the mcp4018 was read only, and set at the time of
configuration. This allows you to change the value during a
print, which is needed for some older printers that need to
lower the stepper current during preheating.
Signed-off-by: Jake Bordens <jake@allaboutjake.com>
This is a working config with full LCD and stepper settings (only thing missing is the kill switch, which did not appear to work)
Signed-off-by: Rui Carmo <rui.carmo@gmail.com>
This is a working config with full LCD and stepper settings (only thing missing is the kill switch, which did not appear to work)
Signed-off-by: Rui Carmo <rui.carmo@gmail.com>
This PR serves to fix a longstanding misnomer in some config files. Many configs state a nozzle_cooling_fan alias for what is usually a "hotend cooling fan". This causes ambiguity and confusion with the parts fan. I have identified all 24 files with this and changed them here.
Signed-off-by: James Hartley <james@hartleyns.com>
Introduce support for the stock Creality CR10 v3 printer, including the filament runout sensor. It also supports the optional BLTouch.
Signed-off-by: Luís Palma Nunes Mendes <luis.p.mendes@gmail.com>
Create configuration file for Fly-Gemini-v1 motherboard
Add stm32f405 and generic-mellow-fly-gemini-v1.cfg to test cases
Signed-off-by: Xiaokui Zhao <xiaok@zxkxz.cn>
* Update and rename printer-twotrees-sapphire-pro-2020.cfg to printer-twotrees-sapphire-pro-sp-3.cfg
I renamed the file since the printer name now changed and is sold with this name, there is only one version so year can be removed.
-Added detailed instructions for flashing in the header.
-Corrected rotation distances for axes, it was wrong.
-Added gear ratio for extruder that is useful for future changes.
-Added heater fan to HE1 pins for automatic shutdown with temp.
-Reduced speed and accel for Z since a 2mm screw is used.
* Create printer-twotrees-sapphire-plus-sp-5-v1.1.cfg
I created the file since the printer name now changed and is sold with this name, there are 2 main versions (V1 and V1.1) so I will make 2 different configs for them since there are some hardware change and people are confused in what to change.
The difference with V1 is that all 2225 drivers are now used, since microsteps tables change for these drivers and by factory all jumpers are in the microstep setting is 32, people don't know this and will have half movement with the v1 config, there is a lot of confusion in communities so I think adding another file is the best option.
Signed-off-by: Lorenzo Cascone <laurienzudesign@gmail.com>
This file includes the build instructions and generic configuration for the TH3D EZBoard Lite v2.0 3d printer control board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
Lines 94 and 97. Fan speed should be 1 and not 0.5
removed lines to use default settings.
[heater_fan hotend_fan]
pin: PG14
[fan]
pin: PG13
Signed-off-by: Scott Schering <sschering@gmail.com>
The fan pin PA0 is not correct for the 2021 revision of the CR-6 SE using the
4.5.3 revision of the Creality board. Changed the pin to PB15 in order to
get it working
Signed-off-by: Filip Trplan <filip@trplan.si>
TMC2130/5160 can make use of `spi3`, which is operated on the software SPI pins in the current configuration. The supplied defaults for software SPI do not currently work.
Heater0 pin was marked incorrectly, should be `PB0`
Signed-Off-By: Wijnand Modderman-Lenstra <maze@maze.io>
Many non-English speaking countries use a comma as a decimal separator for printed numbers. This can create some confusion in documentation and config files when not surrounded by contextual clues like parenthesis. Improve documentation by adding spaces to coordinates.
Signed-off-by: Paul McGowan <mental450@gmail.com>
There is no reason to explicitly set the interpolate flag to true in
the example configs as that is already the default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the documentation recommends that hold_current not be set,
update the example config files to not specify a hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Updates for generic-bigtreetech-skr-2.cfg to include comment on newly shipped board with STM32F429 instead of the original STM32F407
Signed-off-by: James Hartley <james@hartleyns.com>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Example default config for Tronxy XY-2 Pro.
It is default config for printer Tronxy XY-2 Pro (mainboard Chitu V6). This config based on config for Tronxy X5SA with mainboard Chitu V6.
Signed-off-by: Konstantin Bazhenin <kby@list.ru>
This commit contains a configuration for the Anycubic Vyper printer from 2021.
It uses a clone of the STM32F103 chip named GD32F103.
There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
since there are no different changes in the Anycubic Marlin firmware.
The LCD is not supported yet (might work, but didn't try yet).
Signed-off-by: Marc Neuhaus <marc@neuhaus.nrw>
Signed-off-by: Manuel Fichtner <manuel.fichtner@me.com>
Fixing initial rotation distance on Thinker S stocker extruder
Removing author information
Fixing Z Axis homing speed as it was too fast.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
This config I created and fully tested on my own printer Anycubic 4Max Pro 2.0. This works fine! Please note that this printer is different from the Anycubic 4MAX.
Signed-off-by: Alexander Usachev <int_0x21@protonmail.com>
This is just a short inline comment about Bigtreetech's implementation of the "anti-reversal stepper protection" and the way it should be handled in the Klipper printer configuration.
Signed-off-by: Jerry Chapman <truckershitch@hambone.e4ward.com>
dahliamoth