Introduce a new handle_fault() method to handle processing of sensor
faults. This simplifies the calc_temp() methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the fault information explicitly in the query_thermocouple fault
field for max6675, max31855, and max31865.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a tmc driver can't find the stepper config section it reports a
"missing microsteps" error which can be confusing. Provide a more
explicit error message.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added a SET_DIGIPOT command to the mcp4018 implementation.
Previously the mcp4018 was read only, and set at the time of
configuration. This allows you to change the value during a
print, which is needed for some older printers that need to
lower the stepper current during preheating.
Signed-off-by: Jake Bordens <jake@allaboutjake.com>
Also added status report for extruder_stepper objects with the
current pressure advance parameters values.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Removes a call to gcmd.respond_info which writes 'VARIABLE SAVED' to the
console every time the SAVE_VARIABLE command is called.
Signed-off-by: Andre LeBlanc <mapleleafmakers@gmail.com>
Raised from issue #5645, UTF-8 encoded symbols or other unexpected symbols on the UART raise an exception which causes klipper to stop. This change support UTF-8 encoded characters (from file names) as well as ignoring unexpected bytes.
Signed-off-by: Clifford Roche <clifford.roche@gmail.com>
An mcu device acting as an "mcu bridge" should only be reset after
other normal devices are reset - otherwise the bridge wont be able to
pass along the reset message to the downstream mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Starting with nodeid 4 instead of nodeid 0 can reduce bitstuffing of
the id field in common configurations.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The `logging.basicConfig` does not reconfigure default logger.
This results in printing only warnings/errors to stderr
instead of also info (or debug).
This fixes the issue by setting log level on root logger.
Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Calling python functions can have high overhead. Inline the
twos_complement code in the _extract_samples() inner loop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MPU9250CommandHelper() class is nearly a duplicate of
ADXL345CommandHelper(). Rename ADXL345QueryHelper() to
AccelCommandHelper and remove user facing references to "adxl345". Use
it directly from mpu9250.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The mpu9250.ClockSyncRegression() class is a duplicate of
adxl345.ClockSyncRegression(). Remove the duplicate copy and use the
code from adxl345.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MPU9250QueryHelper() class is a duplicate of ADXL345QueryHelper().
Rename ADXL345QueryHelper() to AccelQueryHelper() and use it directly
from mpu9250.py .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds a save_config_pending_items to the status reported by
configfile reflecting the items and values that a future
SAVE_CONFIG would actually persist.
Signed-off-by: Kurt Haenen <kurt.haenen@gmail.com>
Just log an error on a fault.
Remove the host check for min/max temperature as the micro-controller
code already implements that check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allows a limited number of DS18B20 read failures
before stopping the printer. This is designed to
tolerate spurious read errors, while still stopping
for serious issues.
The printer will stop when the sensor
fails to report a value five times in a row.
Implementation works as follows:
The MCU reports any read errors using a new "fault"
parameter in its answers.
The Python code tracks the number of errors
and triggers the shutdown. This paves the way for
more sophisticated error handling in the future,
as well as an example for other sensors to follow.
Signed-off-by: Lorenzo Pfeifer <Lorenzo.Pfeifer+github@googlemail.com>
Adding Klipper functionality to support cancelling objects while
printing.
This module keeps track of motion in and out of objects and adjusts
movements as needed. It also tracks object status and provides that to
clients.
The Klipper module is relatively simple, and only provides one piece of
the workflow. Moonraker already supports processing uploaded files to
insert the required gcode markers for cancelling objects, using
https://github.com/kageurufu/cancelobject-preprocessor. This library is
also available as an executable for use in slicers, and pip
installations also include the script as a callable.
Mainsail has integrated support, and code changes for Fluidd are
available. Support in other interfaces is planned, and we've spoken to
several other developers about integrating frontend support in their
projects.
Signed-off-by: Troy Jacobson <troy.d.jacobson@gmail.com>
Co-authored-by: Franklyn Tackitt <git@frank.af>
Co-authored-by: Eric Callahan <arksine.code@gmail.com>
Add PROBE and CHIP to TEST_RESONANCES
Since it's possible to specify more than one chip
in TEST_RESONANCES the CHIP parameter has been
renamed to CHIPS
Signed-off-by: Mikkel Schmidt <mikkel.schmidt@gmail.com>
Make sure whitespace isn't in the pin description. Also make sure an
alias doesn't map to an invalid pin.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor indentation and variable name changes.
Don't remove linebreaks from message_protocol_error lines.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MCU protocol error message often confuses users, especially after getting bombarded with the config format error line. This PR tries to improve it and has the following goals:
- Put the technical error at the end to prevent confusion and avoid the immediate jump to help channels instead of continuing to read
- Inform the user first what the type of error is (In this case: MCU Protocol error) and not at the end of the long error message
- Give the users a clear instruction what to do (pretty much unchanged), but possibly more approachable because the user is not confused by the technical error anymore
- Shows the version numbers of Klipper separate from all MCU version numbers so that it is more obvious that this is the version of Klipper
- Separates the version numbers between outdated MCUs and up-to-date MCUs, so that it becomes obvious if a MCU flash failed because the MCU doesn't disappear from the outdated list
- Previously, when viewing the errors in a web frontend, additional line breaks made it extremely hard to read the message, sometimes with as little as one word on one line. The error messages are now formatted to not have rogue line breaks, improving readability.
Signed-off-by: Felicia Alexa Hummel <felicia@drachenkatze.org>
If the final update in a series of SET_LED update commands didn't
alter a color than the transmit would not occur - even if prior
commands did make color changes. Refactor the update code and fix.
Reported by @mstansberry.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This is most probably the result of a copy paste error. All vendor documentation for SI7021 (e.g. https://www.silabs.com/documents/public/data-sheets/Si7021-A20.pdf) points to 21 and it actually only works when adapted to 0x15 (=21).
Signed-off-by: Uli Wolf <github+klipper@wolf-u.li>
Added PCA9632 LED module support using software I2C from MCP4018
modulo drive the LED strip of a FlashForge Dreamer 3D printer.
Based on the PCA9533 module.
Signed-off-by: Ricardo Alcantara <ricardo@vulcanolabs.xyz>
Check that a SET_PRESSURE_ADVANCE without an explicit EXTRUDER
parameter isn't done after the user disables or reassociates the
extruder stepper motor (via SYNC_EXTRUDER_MOTION). Otherwise, it
could lead to very confusing results.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support altering the extruder distance using the higher-level
rotation_distance. This is in preparation for removal of the
SET_EXTRUDER_STEP_DISTANCE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The G2 / G3 command might be renamed using `gcode_macro` + `rename_existing`. This change allow detecting clockwise / anti-clockwise moves when the command gets renamed.
Signed-off-by: Nick Douma <n.douma@nekoconeko.nl>
Commit 7ef7bf60 broke the special handling for M117 commands that
start with a number or special character. Fix that support and extend
to M118 as well.
Also improve handling of commands not separated by a space (eg,
"M117HELLO").
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the extruder_stepper support so that it uses the
ExtruderStepper class defined in extruder.py.
Support the SYNC_STEPPER_TO_EXTRUDER command on steppers defined in
either extruder_stepper or extruder config sections.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the pressure_advance value in "struct extruder_stepper" instead
of in the trapq's "struct move". This makes it possible for multiple
stepper motors to have different pressure advance values while still
using the same trapq.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is preferable to program the tmc drivers with an irun (or cs)
setting near 31, as otherwise the driver may have reduced microstep
precision. It was possible for the driver to be programmed with
irun=16 or irun=17 when it could have been configured with irun=31
with vsense=1 instead. This would occur on tmc2130/tmc2208/tmc2209
drivers for values around 0.900 to 1.000 amps (when using a typical
sense_resistor settings of 0.110 Ohms).
Change the code to prefer using vsense=1 to avoid this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Previously accidentally used 'default' state name instead of the
stated one ('PAUSE_STATE'). This might collide with user usage of the
SAVE_GCODE_STATE macro.
Signed-off-by: David Grundberg <individ@acc.umu.se>
Commit 689231df changed the default step_pulse_duration to 100ns for
TMC drivers that are configured in UART/SPI mode, but it failed to
document that change in Config_Changes.md and Config_Reference.md.
Update those documents to reflect that change.
Update the code so that a user may specify a custom
step_pulse_duration even on TMC drivers that are configured in
UART/SPI mode. This may be useful for drivers that use a level
shifter on the step pin that requires more than a ~300ns to detect a
level change.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The mcu can only enforce the max duration if the start value is the
same as the shutdown value, so verify that before configuing the mcu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a copy of the dictionary prior to updating the the variable field.
This fixes an issue where webhooks holds a reference to the variables
dict returned by get_status().
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
It seems the common "beta 3950" thermistors generally follow a
temperature table defined by the new "Generic 3950" definition. Using
a table that actually follows the "beta 3950" temperature curve is
generally less accurate. Deprecate the existing "NTC 100K beta 3950"
definition to avoid this common issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the definitions of the default thermistors from thermistors.py to
the temperature_sensors.cfg file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the default list of sensor modules from heaters.py to a new
temperature_sensors.cfg config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 9ecddd1b fixed a serious error (introduced in 7d95a004). Force
a protocol version change so users are aware of the need to update the
mcu code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add an optimized step function for drivers that support stepping on
both rising and falling edges of the step pin. Enable this
optimization on 32bit ARM micro-controllers. Automatically detect
this capability in the host code and enable on TMC drivers running in
SPI/UART mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the STEP_DELAY Kconfig option and replace it with a per-stepper
step_pulse_duration printer.cfg config option.
The AVR code will continue to have optimized code to step and "unstep"
in the same function (which is automatically activated when the step
delay is 40 ticks or less). This change removes the Kconfig option
for single function step/unstep on 32bit processors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove support for default_parameter_xxx config options. Remove
support for direct access to command parameters.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Avoid using unicode() types on Python2 as it can lead to subtle
errors.
Also, accept utf8 on gcode input (instead of just ascii).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This resolves an issue where the timer can get stuck
in an attempt to transition from Ready to Idle if
the printer is shutdown.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
The code automatically reduces the hold_current so that it is no
greater than the run_current. However, this could lead to confusing
behavior if one reduced and then increased the run_current via
SET_TMC_CURRENT commands. To avoid that, this change adds support for
tracking the requested hold_current - thus changes to run_current
don't subtly alter the hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor