3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
5,036 Commits 1 Branch 0 Tags 27 MiB
Commit Graph

142 Commits

Author SHA1 Message Date
JamesH1978 f163a37f5e
docs: Update Config_Reference.md - heater_fan wording (#6273) 
The reference to my_nozzle_fan is misleading and could cause people to skip over the [fan] definition and assume this is the parts/print cooling fan. Alias changed to reflect heatbreak_cooling_fan as used in most configs that have a controllable hotend fan.

Signed-off-by: James Hartley <james@hartleyns.com>
 2023-06-28 19:52:40 -04:00
Kevin O'Connor 2ae3dd2f78 docs: Improve documentation of i2c_software_scl_pin/i2c_software_sda_pin 
Reported by @rootiest

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2023-06-20 12:00:59 -04:00
Eric Callahan 8fe18f27a9 docs: update Bed Mesh documentation 
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
 2023-06-20 11:48:17 -04:00
Alex Voinea 5ee72d320c tmc: Configurable `multistep_filt` 
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
 2023-06-16 16:38:42 -04:00
BIGTREETECH 645a1b8364
i2c_software: Implementation of software i2c (#6141) 
Signed-off-by: Alan.Ma from BigTreeTech <tech@biqu3d.com>
 2023-06-07 20:55:46 -04:00
Scott Mudge 10e816979e aht10: update comments and docs for AHT20/AHT21 support 
The control bytes for the AHT20 and AHT21 are identical to the AHT10, but I had not been able to test just yet to ensure the sensor code supported the other sensors. I've wrapped up testing and updated the comments/docs to reflect this additional support.

Signed-off-by: Scott Mudge <mail@scottmudge.com>
 2023-04-24 11:10:00 -04:00
Scott Mudge 4748dffd7a
docs: Add AHT10 temperature sensor doc section in Config_Reference.md (followup #6138) (#6167) 
Followed general outline used by HTU21D and BME280.

Signed-off-by: Scott Mudge <mail@scottmudge.com>
 2023-04-15 19:17:54 -04:00
vcore85 c2b2278a49
tmc5160: add DRV_CONF Register for TMC5160 (#6154) 
In some condition ，“drvstrength 2” does not work. According to page 17, some mosfets need “drvstrength” set to 0 .

From datasheet rev1.15, the DRVSTRENGTH reset default is 0 .  (instead of 2)

Signed-off-by: Albert Lin <vcore85@gmail.com>
 2023-04-11 11:43:19 -04:00
BIGTREETECH 346e3901f6
tmc: Enable sg_angle_offset for smooth switching from Stealthchop to Spreadcycle (#6123) 
Signed-off-by: Alan.Ma from BigTreeTech <tech@biqu3d.com>
 2023-03-27 21:18:06 -04:00
Dr. Matthew Swabey 2466b7a2c6
avr: Allow I2C bus speed to be set by Klipper (#6111) 
Allow I2C bus speed to be set by appropriate Klipper commands.

Signed-off-by: Matthew Swabey <matthew@swabey.org>
 2023-03-21 15:02:58 -04:00
Alex Voinea 6b75f54e50 tmc2240: initial implementation 
Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2023-03-01 20:43:53 -05:00
Thijs Triemstra 848a78d1a5
docs: Fix typos (#6032) 
Signed-off-by: Thijs Triemstra <info@collab.nl>
 2023-02-20 11:06:25 -05:00
Bassam Husain ae9169c4c3
docs: Fix 'screw_thread' explanation in 'screws_tilt_adjust' section. (#6039) 
Signed-off-by: Bassam Husain <bassam.husain@gmail.com>
 2023-02-09 11:30:41 -05:00
CODeRUS f57ff2c07e docs: Fix typo in mpu9250 documentation 
Adding MPU-6515, replacing MPU-9255 duplicate

Signed-off-by: Andrei Kozhevnikov <coderusinbox@gmail.com>
 2022-12-30 22:28:59 -05:00
Alex Voinea 9b60daf62d
tmc: Configurable microstep lookup table (#5920) 
Make all the microstep lookup table registers configurable via the
config file. It also loads the default values.
TMC220x and TMC2660 do not support this feature.

Signed-off-by: Alex Voinea <voinea.dragos.alexandru@gmail.com>
 2022-12-21 21:23:23 -05:00
Yifei Ding d17ef95a3c
mpu9250: add MPU6500 (#5767) 
Signed-off-by: Yifei Ding <yifeiding@protonmail.com>
 2022-11-19 09:58:24 -05:00
alchemyEngine 34870d3e2a
z_thermal_adjust: Add Z thermal adjuster module (#4157) 
Use a frame-coupled temperature probe to compensate for thermal
expansion in real-time.

Signed-off by: Robert Pazdzior <robertp@norbital.com>
 2022-09-25 12:39:14 -04:00
dalegaard 9f8f3cd77d
fan: add enable_pin option (#5732) 
Signed-off-by: Lasse Dalegaard <dalegaard@gmail.com>
 2022-09-03 12:23:55 -04:00
Tircown 354915d2ad
kinematics: Add deltesian printers (#5743) 
Initial push of the working deltesian kinematics after some successful tests.

Signed-off-by: Fabrice GALLET <tircown@gmail.com>
 2022-09-01 15:56:31 -04:00
Pedro Lamas c29e190696 docs: fixes typo on heater_bed 
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
 2022-07-28 20:37:34 -04:00
Kevin O'Connor 52a8afba43 docs: Note mcu types with i2c_speed support in Config_Reference.md 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-06-20 12:58:05 -04:00
Kevin O'Connor 98a24172e7 docs: Add mpu9250 to Config_Reference.md 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-06-20 12:41:24 -04:00
Kevin O'Connor 55d1c3728d docs: Note that i2c is not noise resilient in Config_Reference.md 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-06-16 18:38:31 -04:00
Frank Tackitt 638cd4d781 docs: add exclude_object documentation 
Also include sample macros to add M486 compatibility.

Signed-off-by: Franklyn Tackitt <git@frank.af>
Co-authored-by: Troy Jacobson <troy.d.jacobson@gmail.com>
 2022-06-03 14:12:04 -04:00
Pedro Lamas c16eab212e virtual_sdcard: Adds on_error_gcode 
Signed-off-by: Pedro Lamas <pedrolamas@gmail.com>
 2022-06-03 11:26:34 -04:00
camerony f1c6f76a51
docs: Update Config_Reference.md z_hop speed (#5514) 
The default z-hop speed is actually 15 mm/s according to the code in safe_z_home.py

Signed-off-by: Cameron River <camerony@gmail.com>
 2022-05-23 15:05:53 -04:00
Kevin O'Connor 07a90902a5 docs: Improve wording of screws_tilt_adjust in Config_Reference.md 
Reported by @JamesH1978.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-23 21:22:02 -04:00
Kevin O'Connor 5f0885958d neopixel: Support chains with a mix of color_order 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-18 10:16:10 -04:00
Kevin O'Connor 4a8a76ead8 docs: Update temperature_fan PID documentation in Config_Reference.md 
Reported by @dewi-ny-je.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-11 11:46:24 -04:00
Karl Bowden 5d82be2f5d
docs: Add link to linux mcu neopixels config docs (#5402) 
The reference to the linux mcu was helpful to understand what a linux mcu was but didn't help with understanding the technical reasons why it's not supported.

Signed-off-by: Karl Bowden <karl@bearded.sexy>
 2022-04-11 10:35:38 -04:00
Kevin O'Connor 05330fd3e5 docs: Minor updates to SmartEffector docs 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-09 19:10:16 -04:00
Dmitry Butyugin 2060a6908f smart_effector: Config and command reference 
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
 2022-04-09 19:04:57 -04:00
cbc02009 f3b995227a
docster: Fix incorrect default value for max_freq 2022-04-09 16:31:23 -04:00
Kevin O'Connor 5a409d5d31 docs: Provide more information on PID in Config_Reference.md 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-07 12:30:02 -04:00
Kevin O'Connor 555ac58a3f pca9632: Add support for configurable color_order 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-07 11:48:25 -04:00
Kevin O'Connor f0700c0985 pca9632: Support using hardware I2C 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-07 11:43:52 -04:00
Kevin O'Connor dc7b02f329 neopixel: Support arbitrary RGBW strings in color_order config 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-04-06 09:27:36 -04:00
Kevin O'Connor 1ab3ac39e4 led: Support automated LED updates based on display_template results 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-31 13:08:12 -04:00
Kevin O'Connor 35ff49e546 docs: Note that neopixel doesn't work on "linux mcu" 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-31 13:08:12 -04:00
Kevin O'Connor 96795def9c led: Add support for PWM controlled LEDs 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-31 13:08:12 -04:00
Kevin O'Connor aec742ece4 angle: Initial support for angle sensor calibration 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-29 20:34:46 -04:00
Kevin O'Connor 74937326d3 sensor_angle: Add support for bulk querying of spi angle sensors 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-29 20:34:46 -04:00
Charles Pickering 7e654aed2f docs: Fix config snippet for polar 
Previously the section for stepper_bed was intertwined with printer. This commit makes it match (../config/example-polar.cfg).

Signed-off-by: Charles Pickering <me@charlespick.xyz>
 2022-03-20 11:43:32 -04:00
Kevin O'Connor d7f8bf351f docs: Fix section headers of [display] sections in Config_Reference.md 
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-16 12:04:41 -04:00
Ricardo Alcântara 0761026e36
pca9632: LED module for FlashForge Dreamer 3D printer (#4654) 
Added PCA9632 LED module support using software I2C from MCP4018
modulo drive the LED strip of a FlashForge Dreamer 3D printer.
Based on the PCA9533 module. 

Signed-off-by: Ricardo Alcantara <ricardo@vulcanolabs.xyz>
 2022-03-14 14:28:42 -04:00
electron2410 02d770ae3c
neopixel: add BGR for neopixel (#5160) 
Signed-off-by: Thomas Liebold <electron2410@gmail.com>
 2022-03-14 12:30:58 -04:00
Fritz Webering 24e7bbf0df
docs: Add missing bltouch lift_speed option to Config_Reference.md (#5344) 
Signed-off-by: Fritz Webering <fritz@webering.eu>
 2022-03-11 13:35:08 -05:00
Kevin O'Connor 4815a946c2 extruder_stepper: Do not default to synching with "extruder" at startup 
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-04 13:38:59 -05:00
Kevin O'Connor 6627d036ac extruder: Allow an extruder object to be created without a stepper 
This may be useful for dual hotend printers that have only one
stepper.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-03-04 13:20:35 -05:00
Kevin O'Connor 2e17519a7e extruder: Deprecate old extruder commands and shared_heater config option 
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.

Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
 2022-02-10 13:25:16 -05:00