Commit Graph

23 Commits

Author SHA1 Message Date
Master92 3a37d4a208 safe_z_home: Hop only if necessary and add option to move xy back
Once a hop is performed, it will only be re-issued if the z-axis has been
moved in the meantime. Usually it is only moved by a z-homing so doing so
will cause safe_z_home to do the hop on the next homing action.

When z-axis is homed, x and y positions are known. When setting this
boolean option, these are set back to their last positions.

Whenever a hop is specified it is re-issued after the Z axis has been
homed. This is especially necessary when a pressure-based probe is used.
Also, the module decides if a hop is necessary, based on either a known
Z position or a flag that is set whenever the motors are disabled.

Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
2019-09-18 09:37:33 -04:00
Kevin O'Connor 4c09d8bf02 dotstar: Initial support for "dotstar" LEDs
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-08-06 19:44:32 -04:00
Kevin O'Connor a878831d5e mcp4728: Update to better match printrbot revf requirements
Reported by @Grumps49.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-26 11:02:56 -04:00
Kevin O'Connor 0343d0c73a firmware_retract: Remove z_hop support
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.

The z_hop support is therefore being removed until these issues can be
fixed.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 19:25:56 -04:00
Kevin O'Connor 364c22fe84 probe: Rework the PROBE_ACCURACY command parameters
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10.  Instead, use the "retract
distance" method that is used for normal multi-sample probing.

Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-07-10 15:21:09 -04:00
Arksine 57eb0e8975 docs: Update for latest changs to skew_correction
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2019-06-29 10:58:46 -04:00
Kevin O'Connor 8b00580884 gcode_macro: Parse variable_X parameters using ast.literal_eval()
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-07 19:33:31 -04:00
Kevin O'Connor a541c2f60e docs: Update Config_Changes.md with "samples" move to probe config section
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-06 10:15:47 -04:00
Kevin O'Connor ac8f6dfe20 gcode_macro: Rename "status" helper to "printer"
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-06-04 09:50:30 -04:00
Kevin O'Connor d6b69938ab gcode: Don't apply the SET_GCODE_OFFSET to the next g-code command
The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command.  (In particular,
when the following command is an extrude only move - as in
issue #1289.)

Don't apply the offset immediately.  Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-05-26 11:19:15 -04:00
Kevin O'Connor 6318bdc99b docs: Note the python software dependency update in Config_Changes.md
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-05 11:20:36 -04:00
Kevin O'Connor 0615ab5f89 docs: Note the use of bus enumerations in Config_Changes.md
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:30:04 -04:00
Kevin O'Connor be6b29fabf sx1509: Convert code to use generic i2c bus support
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-04-04 18:29:30 -04:00
Douglas Hammond c105adc80b temperature_fan: Fix. Temperature fan min speed should be used (#1405)
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
2019-03-28 14:07:40 -04:00
Kevin O'Connor 9aadc3c7fa docs: Also note that driver_VSENSE was removed from tmc2660 driver
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 22:40:42 -04:00
Kevin O'Connor efab177645 docs: Note tmc2660 driver_HEND default change from 6 to 3
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-22 20:41:32 -04:00
Kevin O'Connor d3f6dad853 controller_fan: Allow multiple controller_fan sections to be defined
It may be necessary to define multiple fans, so allow each config
section to be named.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-10 13:57:01 -04:00
Kevin O'Connor 563bc37073 tmc2130: Rename driver_BLANK_TIME_SELECT to driver_TBL
Use the field names from the trinamic specification.  This makes the
field similar to all the other driver_XXX config options.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:25:19 -05:00
Kevin O'Connor 89935c6831 docs: Update Config_Changes.md with tmc2660 changes
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-08 11:08:24 -05:00
Kevin O'Connor c8d7e28a35 atsamd: Add support for programming SERCOM pins
Signed-off-by: Florian Heilmann <Florian.Heilmann@gmx.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-03-01 00:40:44 -05:00
Arksine f7d8854587 bed_mesh: simplify configuration
The 'bed_shape' option has been removed.  The user will enter a 'bed_radius' if they have a round be, otherwise they should enter 'min_point' and 'max_point'.  When the bed is round the user should supply a 'round_probe_count' option, otherwise just 'probe_count'.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
2019-02-25 13:34:14 -05:00
Kevin O'Connor e26d1a3567 i2ccmds: Pass the i2c address as a 7-bit number (0-127)
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero.  A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).

Consistently use 7-bit addresses in all the code.  This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 20:00:44 -05:00
Kevin O'Connor f2f54290e8 docs: Add a new Config_Changes.md document
Add a document to track non-backwards compatible changes to the
printer config file.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2019-01-07 20:00:44 -05:00