This reverts commit 5c8d15bbee.
The lower_probe() code was already manually optimizing the timing of
the pwm disable, and that conflicted with the optimization in commit
5c8d15bb.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some clones don't raise the pin on a reset and the ANTClabs BL-Touch
sometimes doesn't raise the pin either.
Rework the (infrequently called) sensor test code to always issue a
pin_up command before the touch command. Also, perform a reset and
retry if the sensor test fails.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be sure to fully raise the probe prior to starting any future toolhead
movements in the multi_probe_end() case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an error is found during the pin_up_not_triggered check, then apply
the reset command for a full second (instead of just 100ms). This
gives the bltouch more time to check its internal state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Return the triggered state from verify_state() and update the callers
to raise the error (if needed).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is likely only developers will be interested in testing the menu
system, so no need to have it in the default menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Disable support for customizing the main lcd display content via the
menu system. Advise users to use the new display_data config sections
as a replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a new config based system for specifying the on-screen
contents of an lcd screen. The default screen configuration (found in
klippy/extras/display/display.cfg) is the same as the previous
hard-coded display, so this should not change behavior for existing
users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use new mcu.lookup_query_command() for all commands that query
information from the micro-controller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert standard queries to use the acknowledgments of the sent
command to determine if the response was received or not. This also
controls command retransmissions (should the response have been lost).
The tmc_uart.py will continue to use the old mechanism as the tmcuart
responses are not sent synchronously with the query command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's not valid to set the TPWMTHRS in a "klippy:connect" event handler
because the TMCVirtualPinHelper and TMCCommandHelper classes were
expecting that field to be set during the config reading phase.
Revert "tmc: Fix typo preventing stealthchop threshold from being set"
This reverts commit 7d76067ff9.
Revert "tmc: Query the stepper step_distance from the stepper object"
This reverts commit 67b2852249.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change home_wait() to return if the homing operation completed
succesfully or not. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the endstop code to return its trigger completion object during
home_start(). Update the toolhead class to take a completion object
(instead of creating its own). This reduces the number of
intermediate callbacks needed during a homing operation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's simpler to query the "printing" status from the idle_timeout
module on an event than it is to track changes to the printing status.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce min_event_systime and rework the previous start_time,
last_event_time, and event_running flags into this one state tracking
variable.
This also makes a minor change to the behavior of the event_delay - it
is now calculated from the time the command completes execution
(instead of from when the event is first detected). This may make a
difference if there is a long running g-code command occurring during
the detection event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rather than inherit from the BaseSensor, filament sensor implementatons
may instantiate the RunoutHelper and update the filament state via its
note_filament_present method.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add support for notifying the low-level probing handlers that a
multiple probe sequence is occurring. This is in preparation for the
bltouch code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Collapse the "homing:move_begin", "homing:move_end", home_prepare(),
and home_finalize() into two new events: "homing:homing_move_begin"
and "homing:homing_move_end". This simplifies the homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When overriding a g-code command, allow the caller to obtain the
previous command handler. Use this feature in homing_override and
safe_z_home.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor