Commit Graph

2913 Commits

Author SHA1 Message Date
Avery Todd 1758f53b9d
config: Add Ultimaker UltiMainboard v2 config. (#2696)
Adds config for the Ultimaker 2's UltiMainboard v2 board, with the 
correct pins assigned and current control for the A4988 motor
drivers.

Signed-off-by: Avery Todd <averyct@pm.me>
2020-04-08 11:26:39 -04:00
Kevin O'Connor a028aeaf78 Revert "bltouch: No need to pause the toolhead for PWM off commands"
This reverts commit 5c8d15bbee.

The lower_probe() code was already manually optimizing the timing of
the pwm disable, and that conflicted with the optimization in commit
5c8d15bb.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-04 18:51:53 -04:00
sillyfrog 0342c50033
scripts: Update Docker file for current Klipper version (#2666)
Signed-off-by: Trent Davis <tgh@sillyfrog.com>
2020-04-02 20:19:26 -04:00
Kevin O'Connor b2a29c6349 docs: Update BLTouch.md initial tests for users with a regular z endstop
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 17:34:15 -04:00
Kevin O'Connor 5d0658b91b docs: Add BLTouch.md section describing clone config options
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 17:34:15 -04:00
Kevin O'Connor 291fbe0801 docs: Add touch_mode sensor test to BLTouch.md
Describe how to test the sensor pin using the BLTouch touch_mode.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 17:34:15 -04:00
Kevin O'Connor 7a67cb86d5 config: Reword bltouch description in example-extras.cfg
The pin_up_touch_mode_reports_triggered should be set to True on all
genuine BLTouch.

Expand the description for stow_on_each_sample and state the default.

Reword the set_output_mode option to be more similar to other
descriptions.

It is no longer necessary to warn about clones being not supported.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 17:34:15 -04:00
Grigori Goronzy 6d2f3ef4f1 config: Fix reset/restart on Fysetc Cheetah v1.2
Deassert RTS for this board and enable the new Cheetah-specific reset
sequence.

Fixes #2026.

Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
2020-04-02 13:56:50 -04:00
Grigori Goronzy 0a20430e07 serial: Add Fysetc Cheetah board specific reset sequence
Fysetc Cheetah v1.2 boards require a special sequence to reset reliably.
This sequence works for me in all cases. Simpler sequences without
double reset did not work correctly. This is likely because of a weird
stateful circuitry for toggling the bootloader state.

Cheetah boards use RTS to configure bootloader triggering. By default,
pySerial sets RTS on connect, which unfortunately configures the board
to start the bootloader on reset.

Add a toggle for the RTS state to allow users to workaround. The RTS state
is set before the serial connection is opened, so there are no glitches.

Addresses #2026.

Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
2020-04-02 13:56:50 -04:00
Kevin O'Connor 5c8d15bbee bltouch: No need to pause the toolhead for PWM off commands
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor 9f2a025762 bltouch: Don't assume reset will do a pin_up in test_sensor()
Some clones don't raise the pin on a reset and the ANTClabs BL-Touch
sometimes doesn't raise the pin either.

Rework the (infrequently called) sensor test code to always issue a
pin_up command before the touch command.  Also, perform a reset and
retry if the sensor test fails.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor 2b916e79c7 bltouch: Call sync_print_time() on multi_probe_end()
Be sure to fully raise the probe prior to starting any future toolhead
movements in the multi_probe_end() case.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor 5e207d2baa bltouch: Apply reset command for a full second on a raise_probe() failure
If an error is found during the pin_up_not_triggered check, then apply
the reset command for a full second (instead of just 100ms).  This
gives the bltouch more time to check its internal state.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor 3646cc0140 bltouch: Separate out pin_up_not_triggered case in raise_probe()
Simplify raise_probe() by separating out the pin_up_not_triggered
case.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor 87bfa06b9e bltouch: Don't raise an error in verify_state()
Return the triggered state from verify_state() and update the callers
to raise the error (if needed).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-04-02 08:25:22 -04:00
Kevin O'Connor d6034013e7 config: Add example printer-alfawise-u30-2018.cfg config
Reported by @elegos.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-30 21:29:57 -04:00
Kevin O'Connor 3c01b60a88 docs: Update FAQ with TMC2208 "standalone" mode workaround
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-29 11:08:49 -04:00
Kevin O'Connor 77177582cd extruder: step_distance must be positive on SET_EXTRUDER_STEP_DISTANCE
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-28 10:06:02 -04:00
Kevin O'Connor 336af2f28d stepper: No need to pass stepper_kinematics to set_step_dist()
Also, no need to log in stepper.py as the update is already logged in
extruder.py.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-28 10:06:02 -04:00
David Smith d4bf61262e
Extruder: Add g-code to set extruder step_distance (#2598)
Signed off by: David Smith <davidosmith@gmail.com>
2020-03-28 09:52:46 -04:00
Kevin O'Connor 8f8cf7ef41 config: Add example printer-twotrees-sapphire-pro-2020.cfg config
Reported by @thucar.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-26 11:53:06 -04:00
Kevin O'Connor cb414ae914 config: Add example generic-mks-robin-nano.cfg config
Reported by @thucar.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-26 11:53:06 -04:00
Kevin O'Connor 8a3233b397 stepper: Add a config check for obvious incorrect homing_positive_dir
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 16:04:11 -04:00
Kevin O'Connor 302cd38217 update_mks_robin: Add script to update firmware for MKS Robin bootloader
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 10:30:02 -04:00
Kevin O'Connor 91a27ef083 stm32: Add support for 64KiB bootloader on stm32f103
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 10:02:21 -04:00
Kevin O'Connor 886530e777 stm32: Explicitly reset peripheral clocks on stm32f1
It appears some bootloaders do not properly reset some peripherals.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 10:00:45 -04:00
Kevin O'Connor 295fb7fc85 serialhdl: Reduce connection fail timeout from 2.5 minutes to 1.5 minutes
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 10:00:45 -04:00
Kevin O'Connor 48237435b2 klippy: Log shutdown state in invoke_shutdown()
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-24 08:37:36 -04:00
Kevin O'Connor 849cc075dc docs: Fix typo in MANUAL_STEPPER command line
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-23 15:06:32 -04:00
Jeremy Briffaut 6be552f6e6 Allow manual_stepper to run in parallel than an other stepper
Signed-off-by: Jeremy Briffaut <kakou@kakou.org>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-23 14:43:34 -04:00
Kevin O'Connor 6b7e917a8e statistics: Exit loop as soon as MemAvailable found
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 22:04:40 -04:00
Kevin O'Connor 6aae62542c statistics: Add system stats
Report os load, process cpu time, and system available memory to each
statistics report.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 20:02:51 -04:00
Kevin O'Connor f3667fd453 util: Try to dump mcu build information on a connection error
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 13:22:52 -04:00
Kevin O'Connor eeee2a9a35 mcu: Shutdown if a spontaneous restart of an mcu is observed
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 12:20:09 -04:00
Kevin O'Connor 0c9eb519ff docs: Update Manual_Level.md Z_ENDSTOP_CALIBRATE instructions
The endstop must not be triggered at the start of Z_ENDSTOP_CALIBRATE.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 11:18:31 -04:00
Kevin O'Connor 7543876487 docs: Add info on S3D "extra retract distance" to Slicers.md
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 11:00:02 -04:00
Kevin O'Connor df6ca2ea1d config: Add comment on changed Z step_distance to Ender5 config
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-22 08:44:37 -04:00
Kevin O'Connor d3a7d992aa display: Remove unused self.lcd_type variable
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-21 12:12:29 -04:00
kakou-fr 961f68629a
manual_stepper: Fix sensorless endstop for manual_stepper (#2621)
Signed-off-by: Jeremy Briffaut <kakou@kakou.org>
2020-03-20 21:11:36 -04:00
Chester 35d951dabf
config: Add BigTreeTech GTR board generic config file (#2626)
This config was not yet available - I have updated all the pin defines, starting with the BTT SKR board which is the most similar board + tested it on my printer which is currently working with the TMC5160 drivers using software SPI. I have not tested it with other drivers etc but the config should work for them. 

Signed-off-by: Chester Lowrey <hilo90mhz@gmail.com>
2020-03-20 21:02:24 -04:00
Kevin O'Connor acd165cbea stepcompress: Implement a step+dir+step filter
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events.  In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode.  Detect these events and remove them from the
generated step times.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-13 21:53:48 -04:00
Kevin O'Connor d86bf0b927 stepcompress: Move code around in stepcompress.c
Just code movement - no code changes.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-13 21:53:48 -04:00
Kevin O'Connor 5e39d346ed display: Use the active extruder in the default 16x4 screen layout
Change the default layout to show the active extruder (not always the
first extruder).

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-13 21:50:38 -04:00
Kevin O'Connor f2dd4b001d display: Use a separate display group for 16x4 multiple extruders
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-13 21:46:36 -04:00
Garth Snyder 0ba83c5b04
docs: clarify behavior of M204 with only one of P or T (#2564)
Signed-off-by: Garth Snyder <garth@garthsnyder.com>
2020-03-11 13:03:48 -04:00
Kevin O'Connor 986e9c884a display: Fix percent progress rendering on 16x4 multi-extruder layout
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-08 17:55:53 -04:00
Kevin O'Connor 3850b3d27a docs: Fix date of menu change in Config_Changes.md
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-08 17:42:22 -04:00
Arksine aa7d24b0af display: add support for multiple displays
Signed-off-by:  Eric Callahan <arksine.code@gmail.com>
2020-03-08 17:38:24 -04:00
Kevin O'Connor 6d5ce309a5 menu: Remove the "test" menu from the default menu
It is likely only developers will be interested in testing the menu
system, so no need to have it in the default menu.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-08 17:38:24 -04:00
Kevin O'Connor d39c4fe628 menu: Disable support for "deck" and "card" menu items
Disable support for customizing the main lcd display content via the
menu system.  Advise users to use the new display_data config sections
as a replacement.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
2020-03-08 17:38:24 -04:00