Also added status report for extruder_stepper objects with the
current pressure advance parameters values.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Check that a SET_PRESSURE_ADVANCE without an explicit EXTRUDER
parameter isn't done after the user disables or reassociates the
extruder stepper motor (via SYNC_EXTRUDER_MOTION). Otherwise, it
could lead to very confusing results.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Deprecate SET_EXTRUDER_STEP_DISTANCE and SYNC_STEPPER_TO_EXTRUDER.
Recommend using SET_EXTRUDER_ROTATION_DISTANCE and
SYNC_EXTRUDER_MOTION.
Deprecate the extruder "shared_heater" option and reocmmend using
extruder_stepper config sections to obtain the same functionality.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support altering the extruder distance using the higher-level
rotation_distance. This is in preparation for removal of the
SET_EXTRUDER_STEP_DISTANCE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the extruder_stepper support so that it uses the
ExtruderStepper class defined in extruder.py.
Support the SYNC_STEPPER_TO_EXTRUDER command on steppers defined in
either extruder_stepper or extruder config sections.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the pressure_advance value in "struct extruder_stepper" instead
of in the trapq's "struct move". This makes it possible for multiple
stepper motors to have different pressure advance values while still
using the same trapq.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Scale the max_z_velocity limit by the amount of movement in the Z.
This should improve bed_mesh and vase mode prints on delta printers.
Reported by @hywelmartin and @dalegaard.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert stepper.get_past_commanded_position() to the more general
stepper.mcu_to_commanded_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- Add dual_carriage abilities for hybrid-corexy and hybrid-corexz
- Introduce the module idex_mode
- Fix add_stepper to the correct rail in hybrid-corexy
Signed-off-by: Fabrice GALLET <tircown@gmail.com>
Sometimes an automated filament load is implemented,
but extruder might not always extrude filament.
This adds a flag to check if this operation is possible.
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Pass a print_time instead of a clock to get_past_commanded_position().
Fix calculation on steppers that home and use an inverted direction
pin.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The min_stop_interval safety check is fragile and leads to a notable
amount of complexity. Avoid these issues by not programming this
safety check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a heaters.set_temperature() command and call that from
commands that set a heater temperature. This new function calls
toolhead.register_lookahead_callback() so that the idle_timeout gets
notification that activity has occurred.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The stepper positions will only be in sync after the step generation
code has been flushed. This fixes an "internal error in stepcompress"
error during a SYNC_STEPPER_TO_EXTRUDER command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the get_status() axis_minimum and axis_maximum fields in
advance so that they don't need to be calculated on each get_status()
call.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate a "toolhead:set_position" event on a call to
toolhead.set_position() and use that event to automatically call
gcode.reset_last_position().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework extruder.get_trapq() into extruder.sync_stepper() so that
extruder_stepper.py does not need to directly access the extruder
internals.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The heater logic is an independent module that does not need to be
treated as part of the "core" klipper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Neko-vecter