config: Add example generic-archim2.cfg config
Signed-off-by: Mike Payson <mike@mtw3d.com> Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
0160a7db9a
commit
fc6d045ded
|
@ -0,0 +1,160 @@
|
|||
# This file contains common pin mappings for Ultimachine Archim2
|
||||
# boards. To use this config, the firmware should be compiled for the
|
||||
# SAM3x8e.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC6
|
||||
dir_pin: PC5
|
||||
enable_pin: !PC9
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PD4
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2130 stepper_x]
|
||||
cs_pin: PC7
|
||||
microsteps: 16
|
||||
run_current: .5
|
||||
sense_resistor: 0.120
|
||||
diag1_pin: !PA4
|
||||
spi_software_sclk_pin: PD2
|
||||
spi_software_mosi_pin: PD3
|
||||
spi_software_miso_pin: PD1
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PC12
|
||||
dir_pin: PC11
|
||||
enable_pin: !PC14
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PD6
|
||||
position_endstop: 0
|
||||
position_max: 400
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2130 stepper_y]
|
||||
cs_pin: PC13
|
||||
microsteps: 16
|
||||
run_current: .5
|
||||
sense_resistor: 0.120
|
||||
diag1_pin: !PC15
|
||||
spi_software_sclk_pin: PD2
|
||||
spi_software_mosi_pin: PD3
|
||||
spi_software_miso_pin: PD1
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PC17
|
||||
dir_pin: PC16
|
||||
enable_pin: !PC19
|
||||
step_distance: .0125
|
||||
endstop_pin: ^PA7
|
||||
position_endstop: 0
|
||||
position_max: 400
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2130 stepper_z]
|
||||
cs_pin: PC18
|
||||
microsteps: 16
|
||||
run_current: .5
|
||||
sense_resistor: 0.120
|
||||
diag1_pin: PC4
|
||||
spi_software_sclk_pin: PD2
|
||||
spi_software_mosi_pin: PD3
|
||||
spi_software_miso_pin: PD1
|
||||
|
||||
[extruder]
|
||||
step_pin: PB10
|
||||
dir_pin: PC10
|
||||
enable_pin: !PB22
|
||||
step_distance: .002
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC24
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PB19
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2130 extruder]
|
||||
cs_pin: PC20
|
||||
microsteps: 16
|
||||
run_current: .5
|
||||
sense_resistor: 0.120
|
||||
diag1_pin: !PB23
|
||||
spi_software_sclk_pin: PD2
|
||||
spi_software_mosi_pin: PD3
|
||||
spi_software_miso_pin: PD1
|
||||
|
||||
#[extruder1]
|
||||
#step_pin: PB26
|
||||
#dir_pin: PB24
|
||||
#enable_pin: !PA11
|
||||
#step_distance: .002
|
||||
#nozzle_diameter: 0.400
|
||||
#filament_diameter: 1.750
|
||||
#heater_pin: PC23
|
||||
#sensor_type: ATC Semitec 104GT-2
|
||||
#sensor_pin: PB18
|
||||
#control: pid
|
||||
#pid_Kp: 22.2
|
||||
#pid_Ki: 1.08
|
||||
#pid_Kd: 114
|
||||
#min_temp: 0
|
||||
#max_temp: 250
|
||||
|
||||
#[tmc2130 extruder1]
|
||||
#cs_pin: PA10
|
||||
#microsteps: 16
|
||||
#run_current: .5
|
||||
#sense_resistor: 0.120
|
||||
#diag1_pin: PD0
|
||||
#spi_software_sclk_pin: PD2
|
||||
#spi_software_mosi_pin: PD3
|
||||
#spi_software_miso_pin: PD1
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PC21
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PB20
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PC26
|
||||
|
||||
[heater_fan nozzle_cooling_fan]
|
||||
pin: PC25
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_sam3x8e_nnn
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
|
||||
########################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
########################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PA14, EXP1_3=PA15, EXP1_5=PA0, EXP1_7=PA1, EXP1_9=<GND>,
|
||||
EXP1_2=PA13, EXP1_4=PA12, EXP1_6=PA16, EXP1_8=PC2, EXP1_10=<5V>,
|
||||
# EXP2 header
|
||||
EXP2_1=PA25, EXP2_3=PB27, EXP2_5=PA3, EXP2_7=PB25, EXP2_9=<GND>,
|
||||
EXP2_2=PA27, EXP2_4=PA29, EXP2_6=PA26, EXP2_8=<RST>, EXP2_10=<3.3V>
|
||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi0"
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
@ -70,6 +70,7 @@ CONFIG ../../config/generic-printrboard-g2.cfg
|
|||
|
||||
# Printers using the sam3x8e
|
||||
DICTIONARY sam3x8e.dict
|
||||
CONFIG ../../config/generic-archim2.cfg
|
||||
CONFIG ../../config/generic-radds.cfg
|
||||
|
||||
# Printers using the sam4s8c
|
||||
|
|
Loading…
Reference in New Issue