config: Add BigTreeTech EBB V1.2 / EBB SB V1.0 / E3EZ / M5P / M8P V1.1 / Octopus Max EZ

Signed-off-by: Alan.Ma from BigTreeTech tech@biqu3d.com
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
bigtreetech 2023-01-12 15:51:37 +08:00 committed by Kevin O'Connor
parent 1979c9d090
commit f250bdfd8a
13 changed files with 1215 additions and 25 deletions

View File

@ -0,0 +1,200 @@
# This file contains common pin mappings for the BIGTREETECH Manta E3EZ
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PB12/PB13)".
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PA14
dir_pin: !PA10
enable_pin: !PA13
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC4
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_y]
step_pin: PC8
dir_pin: !PA15
enable_pin: !PC14
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB0
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_z]
step_pin: PD2
dir_pin: PD4
enable_pin: !PD3
microsteps: 16
rotation_distance: 8
endstop_pin: ^PC6
position_endstop: 0
position_max: 270
[extruder]
step_pin: PD5
dir_pin: !PD6
enable_pin: !PB3
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PB11 #HE0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA4 #TH0
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
#[filament_switch_sensor material_0]
#switch_pin: PC5
#[extruder1]
#step_pin: PB7
#dir_pin: PB6
#enable_pin: !PB4
#heater_pin: PB10 # HE1
#sensor_pin: PA5 # T1
#[filament_switch_sensor material_1]
#switch_pin: PB1
[heater_bed]
heater_pin: PB2 #HB
sensor_type: EPCOS 100K B57560G104F #Generic 3950
sensor_pin: PA3 #TB
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PA8
#[heater_fan fan1]
#pin: PB15
#[heater_fan fan2]
#pin: PB14
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PB8
##diag_pin: PC4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_y]
#uart_pin: PC9
##diag_pin: PB0
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_z]
#uart_pin: PD0
##diag_pin: PC6
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2209 extruder]
#uart_pin: PD1
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder1]
#uart_pin: PB5
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PB8
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10
##diag1_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_y]
#cs_pin: PC9
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_z]
#cs_pin: PD0
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10
##diag1_pin: PF5
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2130 extruder]
#cs_pin: PD1
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder1]
#cs_pin: PB5
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10
#run_current: 0.800
#stealthchop_threshold: 999999
[board_pins]
aliases:
# EXP1 header
EXP1_1=PC1, EXP1_3=PC3, EXP1_5=PC0, EXP1_7=PA2, EXP1_9=<GND>,
EXP1_2=PC2, EXP1_4=<RST>, EXP1_6=PA0, EXP1_8=PA1, EXP1_10=<5V>
#[bltouch]
#sensor_pin: PA6
#control_pin: PA7
#[output_pin PS_ON]
#pin: PA9
#[output_pin pb9_pin]
#pin: PB9
#[neopixel my_neopixel]
#pin: PC7
#[adxl345]
#cs_pin: PC15
#spi_software_miso_pin: PC11
#spi_software_mosi_pin: PC12
#spi_software_sclk_pin: PC10

View File

@ -0,0 +1,199 @@
# This file contains common pin mappings for the BIGTREETECH Manta M5P
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC8
dir_pin: !PC9
enable_pin: !PA15
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD3
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_y]
step_pin: PA10
dir_pin: !PA14
enable_pin: !PA13
microsteps: 16
rotation_distance: 40
endstop_pin: ^PD2
position_endstop: 0
position_max: 200
homing_speed: 50
[stepper_z]
step_pin: PC6
dir_pin: PC7
enable_pin: !PA9
microsteps: 16
rotation_distance: 8
endstop_pin: ^PC3
position_endstop: 0.0
position_max: 200
[extruder]
step_pin: PB12
dir_pin: !PB11
enable_pin: !PA8
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA1
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
#sensor_type:MAX31865
#sensor_pin: PA4
#spi_bus: spi1
#rtd_nominal_r: 100
#rtd_reference_r: 430
#rtd_num_of_wires: 2
#[filament_switch_sensor material_0]
#switch_pin: PC2
#[extruder1]
#step_pin: PB0
#dir_pin: PB1
#enable_pin: !PC4
#heater_pin: PA7
#sensor_pin: PA2
#...
[heater_bed]
heater_pin: PA5
sensor_type: Generic 3950
sensor_pin: PA0
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PA4
#[heater_fan fan1]
#pin: PA3
#[heater_fan SoC_fan]
#pin: CB1: gpio79
#pin: RPI: gpio26
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PD9
#run_current: 0.800
#diag_pin: PD3
#[tmc2209 stepper_y]
#uart_pin: PD8
#run_current: 0.800
#diag_pin: PD2
#[tmc2209 stepper_z]
#uart_pin: PB10
#run_current: 0.800
#diag_pin: PC3
#[tmc2209 extruder]
#uart_pin: PB2
#run_current: 0.600
#diag_pin: PC2
#[tmc2209 extruder1]
#uart_pin: PA6
#run_current: 0.600
#diag_pin:
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PD9
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PD3
#[tmc2130 stepper_y]
#cs_pin: PD8
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PD2
#[tmc2130 stepper_z]
#cs_pin: PB10
#spi_bus: spi2
#run_current: 0.650
#stealthchop_threshold: 999999
#diag1_pin: PC3
#[tmc2130 extruder]
#cs_pin: PB2
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin: PC2
#[tmc2130 extruder1]
#cs_pin: PA6
#spi_bus: spi2
#run_current: 0.800
#stealthchop_threshold: 999999
#diag1_pin:
[board_pins]
aliases:
# EXP1 header
EXP1_1=PD5, EXP1_3=PB3, EXP1_5=PB5, EXP1_7=PB7, EXP1_9=<GND>,
EXP1_2=PD4, EXP1_4=PD6, EXP1_6=PB4, EXP1_8=PB6, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_3=PB8, EXP2_5=PC10, EXP2_7=PC12, EXP2_9=<GND>,
EXP2_2=PB13, EXP2_4=PB9, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
# See the sample-lcd.cfg file for definitions of common LCD displays.
#[bltouch]
#sensor_pin: PC13
#control_pin: PC15
# Proximity switch
#[probe]
#pin: PC15
#[neopixel my_neopixel1]
#pin: PC11
#[neopixel my_neopixel2]
#pin: PC14
#[adxl345]
#cs_pin: PC0
#spi_bus: spi2

View File

@ -258,7 +258,7 @@ aliases:
EXP2_3=PF7, EXP2_4=PB12,
EXP2_5=PE7, EXP2_6=PB11, # Slot in the socket on this side
EXP2_7=PE8, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=PC5
EXP2_9=<GND>, EXP2_10=<NC>
# See the sample-lcd.cfg file for definitions of common LCD displays.
@ -282,3 +282,7 @@ aliases:
#[hall_filament_width_sensor]
#adc1: PC5
#adc2: PB0
#[adxl345]
#cs_pin: PB15
#spi_bus: spi1

View File

@ -0,0 +1,295 @@
# This file contains common pin mappings for the BIGTREETECH Manta M8P
# To use this config, the firmware should be compiled for the
# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD12/PD13)".
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PE2
dir_pin: PB4
enable_pin: !PC11
microsteps: 16
rotation_distance: 40
endstop_pin: ^PF3
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_y]
step_pin: PF12
dir_pin: PF11
enable_pin: !PB3
microsteps: 16
rotation_distance: 40
endstop_pin: ^PF4
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_z]
step_pin: PD7
dir_pin: !PD6
enable_pin: !PF10
microsteps: 16
rotation_distance: 8
endstop_pin: ^PF5
position_endstop: 0
position_max: 270
# Motor4
# The M8P only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
# or other accesory such as an MMU
#[stepper_]
#step_pin: PD3
#dir_pin: PD2
#enable_pin: PD5
#endstop_pin: PC0
#...
[extruder]
step_pin: PC9
dir_pin: PC8
enable_pin: !PD1
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.4
filament_diameter: 1.75
heater_pin: PE3 # HE0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA1 # T0
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
#[filament_switch_sensor material_0]
#switch_pin: PC1
# Motor6
#[extruder1]
#step_pin: PA10
#dir_pin: PA14
#enable_pin: !PA15
#heater_pin: PB5 # HE1
#sensor_pin: PA2 # T1
#...
#[filament_switch_sensor material_1]
#switch_pin: PC2
# Motor7
#[extruder2]
#step_pin: PD11
#dir_pin: PD9
#enable_pin: !PD15
#heater_pin: PB6 # HE2
#sensor_pin: PA3 # T2
#...
# Motor8
#[extruder3]
#step_pin: PD8
#dir_pin: PC6
#enable_pin: !PC7
#heater_pin: PE1 # HE3
#sensor_pin: PA4 # T3
#...
[heater_bed]
heater_pin: PB7
sensor_type: Generic 3950
sensor_pin: PA0 # TB
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PE6
#[heater_fan fan1]
#pin: PE0
#[heater_fan fan2]
#pin: PC12
#[heater_fan fan3]
#pin: PE5
#[heater_fan fan4]
#pin: PE4
#[heater_fan fan5]
#pin: PB8
#tachometer_pin: PC14
#[heater_fan fan6]
#pin: PB9
#tachometer_pin: PC15
#[heater_fan SoC_fan]
#pin: CB1: gpio79
#pin: RPI: gpio26
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PC10
##diag_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_y]
#uart_pin: PF13
##diag_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_z]
#uart_pin: PF9
##diag_pin: PF5
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2209 stepper_]
#uart_pin: PD4
##diag_pin: PC0
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2209 extruder]
#uart_pin: PD0
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder1]
#uart_pin: PF8
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder2]
#uart_pin: PD14
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder3]
#uart_pin: PD10
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PC10
#spi_bus: spi1
##diag1_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_y]
#cs_pin: PF13
#spi_bus: spi1
##diag1_pin: PF4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_z]
#cs_pin: PF9
#spi_bus: spi1
##diag1_pin: PF5
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2130 stepper_]
#cs_pin: PD4
#spi_bus: spi1
##diag1_pin: PC0
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder]
#cs_pin: PD0
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder1]
#cs_pin: PF8
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder2]
#cs_pin: PD14
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder3]
#cs_pin: PD10
#spi_bus: spi1
#run_current: 0.800
#stealthchop_threshold: 999999
[board_pins]
aliases:
# EXP1 header
EXP1_1=PE9, EXP1_2=PE10,
EXP1_3=PE11, EXP1_4=PE12,
EXP1_5=PE13, EXP1_6=PE14, # Slot in the socket on this side
EXP1_7=PE15, EXP1_8=PB10,
EXP1_9=<GND>, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PB14, EXP2_2=PB13,
EXP2_3=PF7, EXP2_4=PB12,
EXP2_5=PE7, EXP2_6=PB11, # Slot in the socket on this side
EXP2_7=PE8, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=<NC>
# See the sample-lcd.cfg file for definitions of common LCD displays.
#[bltouch]
#sensor_pin: PB2
#control_pin: PB1
# Proximity switch
#[probe]
#pin: PF6
#[output_pin ps_on_pin]
#pin: PC3
#[output_pin pc13_pin]
#pin: PC13
#[neopixel my_neopixel_1]
#pin: PA9
#[neopixel my_neopixel_2]
#pin: PB15
#[hall_filament_width_sensor]
#adc1: PC5
#adc2: PB0
#[adxl345]
#cs_pin: PC4
#spi_bus: spi1

View File

@ -0,0 +1,332 @@
# This file contains common pin mappings for the BIGTREETECH Octopus Max EZ.
# To use this config, the firmware should be compiled for the
# STM32H723 with a "128KiB bootloader" "25 MHz crystal"
# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
# See docs/Config_Reference.md for a description of parameters.
# Motor-1
[stepper_x]
step_pin: PC13
dir_pin: PC14
enable_pin: !PE6
microsteps: 16
rotation_distance: 40
endstop_pin: PF0
position_endstop: 0
position_max: 200
homing_speed: 50
# Motor-2
[stepper_y]
step_pin: PE4
dir_pin: PE5
enable_pin: !PE3
microsteps: 16
rotation_distance: 40
endstop_pin: PF2
position_endstop: 0
position_max: 200
homing_speed: 50
# Motor-3
[stepper_z]
step_pin: PE1
dir_pin: PE0
enable_pin: !PE2
microsteps: 16
rotation_distance: 8
endstop_pin: PF4
position_endstop: 0.5
position_max: 200
# Motor-4
# The Octopus only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
# or other accesory such as an MMU
#[stepper_]
#step_pin: PB8
#dir_pin: PB9
#enable_pin: PB7
#endstop_pin: PF3
#...
# Motor-5
[extruder]
step_pin: PB5
dir_pin: PB4
enable_pin: !PB6
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PF6 # HE0
sensor_pin: PB0 # T0
sensor_type: EPCOS 100K B57560G104F
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250
#[filament_switch_sensor material_0]
#switch_pin: PF1
# Motor-6
#[extruder1]
#step_pin: PG15
#dir_pin: PB3
#enable_pin: !PD5
#heater_pin: PA0 # HE1
#sensor_pin: PC5 # T1
#...
#[filament_switch_sensor material_1]
#switch_pin: PC15
# Motor-7
#[extruder2]
#step_pin: PD3
#dir_pin: PD2
#enable_pin: !PD4
#heater_pin: PF9 # HE2
#sensor_pin: PC4 # T2
#...
# Motor-8
#[extruder3]
#step_pin: PA10
#dir_pin: PA9
#enable_pin: !PA15
#heater_pin: PF7 # HE3
#sensor_pin: PA7 # T3
#...
# Motor-9
#[extruder4]
#step_pin: PA8
#dir_pin: PC7
#enable_pin: !PC9
#...
# Motor-10
#[extruder5]
#step_pin: PG6
#dir_pin: PC6
#enable_pin: !PC8
#...
[heater_bed]
heater_pin: PF5
sensor_pin: PB1 # TB
sensor_type: ATC Semitec 104GT-2
control: watermark
min_temp: 0
max_temp: 130
[fan]
pin: PA6
#[heater_fan fan1]
#pin: PA5
#[heater_fan fan2]
#pin: PA4
#[heater_fan fan3]
#pin: PA3
#[heater_fan fan4]
#pin: PA1
#tachometer_pin: PC3
#[heater_fan fan5]
#pin: PF8
#tachometer_pin: PC1
#[heater_fan fan6]
#pin: PA2
#tachometer_pin: PC2
[mcu]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
########################################
# TMC2209 configuration
########################################
#[tmc2209 stepper_x]
#uart_pin: PG14
##diag_pin: PF0
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_y]
#uart_pin: PG13
##diag_pin: PF2
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 stepper_z]
#uart_pin: PG12
##diag_pin: PF4
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2209 stepper_]
#uart_pin: PG11
##diag_pin: PF3
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2209 extruder]
#uart_pin: PG10
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder1]
#uart_pin: PG9
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder2]
#uart_pin: PD7
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder3]
#uart_pin: PD6
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder4]
#uart_pin: PG8
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2209 extruder5]
#uart_pin: PG7
#run_current: 0.800
#stealthchop_threshold: 999999
########################################
# TMC2130 configuration
########################################
#[tmc2130 stepper_x]
#cs_pin: PG14
#spi_bus: spi4
##diag1_pin: PF0
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_y]
#cs_pin: PG13
#spi_bus: spi4
##diag1_pin: PF2
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 stepper_z]
#cs_pin: PG12
#spi_bus: spi4
##diag1_pin: PF4
#run_current: 0.650
#stealthchop_threshold: 999999
#[tmc2130 stepper_]
#cs_pin: PG11
#spi_bus: spi4
##diag1_pin: PF3
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder]
#cs_pin: PG10
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder1]
#cs_pin: PG9
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder2]
#cs_pin: PD7
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder3]
#cs_pin: PD6
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder4]
#cs_pin: PG8
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
#[tmc2130 extruder5]
#cs_pin: PG7
#spi_bus: spi4
#run_current: 0.800
#stealthchop_threshold: 999999
[board_pins]
aliases:
# FPC header, Aliases EXP1 & EXP2 for mini12864
EXP1_1=PG2, EXP1_2=PD15,
EXP1_3=PD14, EXP1_4=PD13,
EXP1_5=PD12, EXP1_6=PD11,
EXP1_7=PD10, EXP1_8=PE15,
EXP1_9=<GND>, EXP1_10=<5V>,
# EXP2 header
EXP2_1=PE13, EXP2_2=PE12,
EXP2_3=PG5, EXP2_4=PE11,
EXP2_5=PG4, EXP2_6=PE14,
EXP2_7=PG3, EXP2_8=<RST>,
EXP2_9=<GND>, EXP2_10=<NC>
# See the sample-lcd.cfg file for definitions of common LCD displays.
#[bltouch]
#sensor_pin: PB14
#control_pin: PB15
# Proximity switch
#[probe]
#pin: PF11
#[output_pin ps_on_pin]
#pin: PF13
#[output_pin pf12_pin]
#pin: PF12
#[neopixel my_neopixel_1]
#pin: PE10
#[neopixel my_neopixel_2]
#pin: PE9
#[hall_filament_width_sensor]
#adc1: PC0
#adc2: PF10
#[adxl345]
#cs_pin: PF14
#spi_bus: spi4

View File

@ -0,0 +1,68 @@
# This file contains common pin mappings for the BIGTREETECH EBBCan
# Canbus board. To use this config, the firmware should be compiled for the
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
# See docs/Config_Reference.md for a description of parameters.
[mcu EBBCan]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
#canbus_uuid: 0e0d81e4210c
[adxl345]
cs_pin: EBBCan:PB12
spi_software_sclk_pin: EBBCan:PB10
spi_software_mosi_pin: EBBCan:PB11
spi_software_miso_pin: EBBCan:PB2
axes_map: x,y,z
[extruder]
step_pin: EBBCan:PD0
dir_pin: !EBBCan:PD1
enable_pin: !EBBCan:PD2
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: EBBCan:PB13
sensor_type: EPCOS 100K B57560G104F
sensor_pin: EBBCan:PA3
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
# sensor_type:MAX31865
# sensor_pin: EBBCan:PA4
# spi_bus: spi1
# rtd_nominal_r: 100
# rtd_reference_r: 430
# rtd_num_of_wires: 2
[tmc2209 extruder]
uart_pin: EBBCan:PA15
run_current: 0.650
stealthchop_threshold: 999999
[fan]
pin: EBBCan:PA0
[heater_fan hotend_fan]
pin: EBBCan:PA1
heater: extruder
heater_temp: 50.0
#[neopixel hotend_rgb]
#pin: EBBCan:PD3
#[bltouch]
#sensor_pin: ^EBBCan:PB8
#control_pin: EBBCan:PB9
#[filament_switch_sensor switch_sensor]
#switch_pin: EBBCan:PB4
#[filament_motion_sensor motion_sensor]
#switch_pin: ^EBBCan:PB3

View File

@ -0,0 +1,84 @@
# This file contains common pin mappings for the BIGTREETECH EBBCan
# Canbus board. To use this config, the firmware should be compiled for the
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
# See docs/Config_Reference.md for a description of parameters.
[mcu EBBCan]
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
#canbus_uuid: 0e0d81e4210c
[temperature_sensor EBB_NTC]
sensor_type: Generic 3950
sensor_pin: EBBCan:PA2
[adxl345]
cs_pin: EBBCan:PB12
spi_software_sclk_pin: EBBCan:PB10
spi_software_mosi_pin: EBBCan:PB11
spi_software_miso_pin: EBBCan:PB2
axes_map: x,y,z
[extruder]
step_pin: EBBCan:PD0
dir_pin: !EBBCan:PD1
enable_pin: !EBBCan:PD2
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: EBBCan:PB13
sensor_type: EPCOS 100K B57560G104F
sensor_pin: EBBCan:PA3
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 250
# sensor_type:MAX31865
# sensor_pin: EBBCan:PA4
# spi_bus: spi1
# rtd_nominal_r: 100
# rtd_reference_r: 430
# rtd_num_of_wires: 2
[tmc2209 extruder]
uart_pin: EBBCan:PA15
run_current: 0.650
stealthchop_threshold: 999999
[fan]
pin: EBBCan:PA0
[heater_fan hotend_fan]
pin: EBBCan:PA1
heater: extruder
heater_temp: 50.0
#[heater_fan 4W_FAN0]
#pin: EBBCan:PB14
#tachometer_pin: EBBCan:PB15
#tachometer_ppr: 1
#[neopixel hotend_rgb]
#pin: EBBCan:PD3
#[bltouch]
#sensor_pin: ^EBBCan:PB8
#control_pin: EBBCan:PB9
## NPN and PNP proximity switch types can be set by jumper
#[probe]
#pin: ^EBBCan:PC13
#[output_pin PB5]
#pin: EBBCan:PB5
#[output_pin PB7]
#pin: EBBCan:PB7
#[output_pin PB6]
#pin: EBBCan:PB6

View File

@ -225,14 +225,22 @@ CONFIG ../../config/generic-fysetc-s6-v2.cfg
CONFIG ../../config/generic-fysetc-spider.cfg
CONFIG ../../config/generic-mks-rumba32-v1.0.cfg
# Printers using the stm32h723
DICTIONARY stm32h723.dict
CONFIG ../../config/generic-bigtreetech-octopus-max-ez.cfg
# Printers using the stm32h743
DICTIONARY stm32h743.dict
CONFIG ../../config/printer-biqu-bx-2021.cfg
CONFIG ../../config/generic-bigtreetech-skr-3.cfg
# Printers using the stm32g0b1
DICTIONARY stm32g0b1.dict
CONFIG ../../config/generic-bigtreetech-manta-m4p.cfg
CONFIG ../../config/generic-bigtreetech-manta-m8p.cfg
CONFIG ../../config/generic-bigtreetech-manta-m5p.cfg
CONFIG ../../config/generic-bigtreetech-manta-m8p-v1.0.cfg
CONFIG ../../config/generic-bigtreetech-manta-m8p-v1.1.cfg
CONFIG ../../config/generic-bigtreetech-manta-e3ez.cfg
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v3.0.cfg
# Printers using the rp2040