config: Rework sample-bltouch.cfg into sample-probe-as-z-endstop.cfg
The example configuration information is more useful for general probe as z_endstop than as a bltouch example. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
7699304f9b
commit
f01ced8ed4
|
@ -1,56 +0,0 @@
|
||||||
# This file provides example config file settings for the BLTouch
|
|
||||||
# automatic bed leveling sensor. This file is just a "snippet" of
|
|
||||||
# sections specific to the BLTouch - it must be added to a config file
|
|
||||||
# containing the configuration of the rest of the printer.
|
|
||||||
|
|
||||||
# Be sure to review and update this config with the appropriate pins
|
|
||||||
# and coordinates for your printer.
|
|
||||||
|
|
||||||
# See the "example.cfg" and "example-extras.cfg" files for a
|
|
||||||
# description of config parameters.
|
|
||||||
|
|
||||||
# Define the BLTouch servo
|
|
||||||
[servo bltouch]
|
|
||||||
pin: ar32
|
|
||||||
maximum_servo_angle: 180
|
|
||||||
minimum_pulse_width: 0.0006
|
|
||||||
maximum_pulse_width: 0.0024
|
|
||||||
|
|
||||||
# Define a probe using the BLTouch
|
|
||||||
[probe]
|
|
||||||
pin: ar30
|
|
||||||
z_offset: 2.345
|
|
||||||
activate_gcode:
|
|
||||||
SET_SERVO SERVO=bltouch ANGLE=10
|
|
||||||
SET_SERVO SERVO=bltouch ANGLE=60
|
|
||||||
G4 P200
|
|
||||||
deactivate_gcode:
|
|
||||||
SET_SERVO SERVO=bltouch ANGLE=90
|
|
||||||
G4 P100
|
|
||||||
|
|
||||||
# Example bed_tilt config section
|
|
||||||
[bed_tilt]
|
|
||||||
points:
|
|
||||||
100,100
|
|
||||||
10,10
|
|
||||||
10,100
|
|
||||||
10,190
|
|
||||||
100,10
|
|
||||||
100,190
|
|
||||||
190,10
|
|
||||||
190,100
|
|
||||||
190,190
|
|
||||||
|
|
||||||
# If the BLTouch is used to home the Z axis, then define a
|
|
||||||
# homing_override section, use probe:z_virtual_endstop as the
|
|
||||||
# endstop_pin in the stepper_z section, and do not set
|
|
||||||
# position_endstop in the stepper_z section.
|
|
||||||
#[homing_override]
|
|
||||||
#set_position_z: 5
|
|
||||||
#axes: z
|
|
||||||
#gcode:
|
|
||||||
# ; G90 ; Uncomment these 2 lines to blindly lift the Z 2mm at start
|
|
||||||
# ; G1 Z7 F600
|
|
||||||
# G28 X0 Y0
|
|
||||||
# G1 X100 Y100 F3600
|
|
||||||
# G28 Z0
|
|
|
@ -0,0 +1,51 @@
|
||||||
|
# This file provides example config file settings for use on a printer
|
||||||
|
# that uses a Z probe instead of a traditional Z endstop switch. This
|
||||||
|
# file is just a "snippet" of config sections - it must be added to a
|
||||||
|
# config file containing the configuration of the rest of the printer.
|
||||||
|
|
||||||
|
# Be sure to review and update this config with the appropriate pins
|
||||||
|
# and coordinates for your printer.
|
||||||
|
|
||||||
|
# See the "example.cfg" and "example-extras.cfg" files for a
|
||||||
|
# description of config parameters.
|
||||||
|
|
||||||
|
# Define a probe
|
||||||
|
[probe]
|
||||||
|
pin: ar30
|
||||||
|
z_offset: 2.345
|
||||||
|
|
||||||
|
# Example settings to add to stepper_z section
|
||||||
|
[stepper_z]
|
||||||
|
endstop_pin: probe:z_virtual_endstop
|
||||||
|
position_min: -2 # The Z carriage may need to travel below the Z=0
|
||||||
|
# homing point if the bed has a significant tilt.
|
||||||
|
|
||||||
|
# The homing_override section modifies the default G28 behavior
|
||||||
|
[homing_override]
|
||||||
|
set_position_z: 5
|
||||||
|
axes: z
|
||||||
|
gcode:
|
||||||
|
; G90 ; Uncomment these 2 lines to blindly lift the Z 2mm at start
|
||||||
|
; G1 Z7 F600
|
||||||
|
G28 X0 Y0
|
||||||
|
G1 X100 Y100 F3600
|
||||||
|
G28 Z0
|
||||||
|
|
||||||
|
# Example bed_tilt config section
|
||||||
|
[bed_tilt]
|
||||||
|
points:
|
||||||
|
100,100
|
||||||
|
10,10
|
||||||
|
10,100
|
||||||
|
10,190
|
||||||
|
100,10
|
||||||
|
100,190
|
||||||
|
190,10
|
||||||
|
190,100
|
||||||
|
190,190
|
||||||
|
|
||||||
|
# Example bed_mesh config section
|
||||||
|
[bed_mesh]
|
||||||
|
min_point: 20,20
|
||||||
|
max_point: 200,200
|
||||||
|
probe_count: 4,4
|
Loading…
Reference in New Issue