diff --git a/config/generic-th3d-ezboard-lite-v1.2.cfg b/config/generic-th3d-ezboard-lite-v1.2.cfg
index 67b8b656..49661361 100644
--- a/config/generic-th3d-ezboard-lite-v1.2.cfg
+++ b/config/generic-th3d-ezboard-lite-v1.2.cfg
@@ -7,11 +7,10 @@
 # file named "firmware.bin" on an SD card and then restart the board
 # with that SD card.
 
-
 # See docs/Config_Reference.md for a description of parameters.
 
 [mcu]
-serial: /dev/serial/by-id/usb-Klipper_lpc1768_1BB0FF16871C4AAF0F5D7C5DC62000F5-if00
+serial: /dev/serial/by-id/usb-Klipper_lpc1768_00000000000000000000000000000000-if00
 
 [printer]
 kinematics: cartesian
@@ -24,7 +23,8 @@ max_z_accel: 100
 step_pin: P2.0
 dir_pin: P1.16
 enable_pin: !P1.17
-rotation_distance: 72
+microsteps: 16
+rotation_distance: 40
 endstop_pin: ^P1.24
 position_endstop: 0
 position_max: 350
@@ -40,7 +40,8 @@ stealthchop_threshold: 999999
 step_pin: P2.1
 dir_pin: P1.10
 enable_pin: !P1.9
-rotation_distance: 72
+microsteps: 16
+rotation_distance: 40
 endstop_pin: ^P1.25
 position_endstop: 0
 position_max: 350
@@ -56,8 +57,9 @@ stealthchop_threshold: 999999
 step_pin: P2.2
 dir_pin: P1.15
 enable_pin: !P1.14
-rotation_distance: 16
-endstop_pin: probe:z_virtual_endstop
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^P1.26
 position_endstop: 0.5
 position_max: 400
 
@@ -72,7 +74,8 @@ stealthchop_threshold: 999999
 step_pin: P2.3
 dir_pin: P1.4
 enable_pin: !P1.8
-roration_distance: 13.5744
+microsteps: 16
+rotation_distance: 34.406
 nozzle_diameter: 0.400
 filament_diameter: 1.750
 heater_pin: P2.7
@@ -97,7 +100,6 @@ heater_pin: P2.5
 sensor_type: EPCOS 100K B57560G104F
 sensor_pin: P0.24
 control: pid
-# tuned for stock hardware with 50 degree Celsius target
 pid_Kp: 54.027
 pid_Ki: 0.770
 pid_Kd: 948.182
@@ -107,12 +109,6 @@ max_temp: 130
 [fan]
 pin: P2.6
 
-#[safe_z_home]
-# home_xy_position: 175,175 # Change coordinates to the center of your print bed
-# speed: 50
-# z_hop: 10
-# z_hop_speed: 5
-
 #[bltouch]
 #sensor_pin: P1.26
 #control_pin: P2.4
@@ -120,12 +116,14 @@ pin: P2.6
 #[filament_switch_sensor my_sensor]
 #switch_pin: P1.27
 
-######################################################################
-# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
-######################################################################
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
 
 [board_pins]
 aliases:
     # EXP1 header
     EXP1_1=P1.31, EXP1_3=P3.26, EXP1_5=P3.25, EXP1_7=P0.16, EXP1_9=<GND>,
-    EXP1_2=P1.30, EXP1_4=<RST>, EXP1_6=P0.15,  EXP1_8=P0.18, EXP1_10=<5V>
+    EXP1_2=P1.30, EXP1_4=<RST>, EXP1_6=P0.15, EXP1_8=P0.18, EXP1_10=<5V>
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index 1c837e0f..668b8687 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -118,6 +118,7 @@ CONFIG ../../config/generic-bigtreetech-skr-e3-turbo.cfg
 CONFIG ../../config/generic-bigtreetech-skr-v1.1.cfg
 CONFIG ../../config/generic-bigtreetech-skr-v1.3.cfg
 CONFIG ../../config/generic-bigtreetech-skr-v1.4.cfg
+CONFIG ../../config/generic-th3d-ezboard-lite-v1.2.cfg
 CONFIG ../../config/generic-mks-sgenl.cfg
 CONFIG ../../config/generic-re-arm.cfg
 CONFIG ../../config/generic-smoothieboard.cfg