config: Update wording of extruder parameters in example.cfg
Try to improve the description of the extruder config limits. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
a7c8476e98
commit
ed13c5733d
|
@ -100,29 +100,28 @@ nozzle_diameter: 0.500
|
|||
# Diameter of the nozzle orifice (in mm). This parameter must be
|
||||
# provided.
|
||||
filament_diameter: 3.500
|
||||
# Diameter of the raw filament (in mm) as it enters the
|
||||
# The nominal diameter of the raw filament (in mm) as it enters the
|
||||
# extruder. This parameter must be provided.
|
||||
#max_extrude_cross_section:
|
||||
# Maximum area of the cross section of an extrusion line (in
|
||||
# mm^2). This setting prevents excessive amounts of extrusion during
|
||||
# relatively small XY moves. If a move requests an extrusion rate
|
||||
# that would exceed this value it will cause an error to be
|
||||
# returned. The default is: 4.0 * nozzle_diameter^2
|
||||
# Maximum area (in mm^2) of an extrusion cross section (eg,
|
||||
# extrusion width multiplied by layer height). This setting prevents
|
||||
# excessive amounts of extrusion during relatively small XY moves.
|
||||
# If a move requests an extrusion rate that would exceed this value
|
||||
# it will cause an error to be returned. The default is: 4.0 *
|
||||
# nozzle_diameter^2
|
||||
#max_extrude_only_distance: 50.0
|
||||
# Maximum length (in mm of raw filament) that an extrude only move
|
||||
# may be. If an extrude only move requests a distance greater than
|
||||
# this value it will cause an error to be returned. The default is
|
||||
# 50mm.
|
||||
# Maximum length (in mm of raw filament) that a retraction or
|
||||
# extrude-only move may have. If a retraction or extrude-only move
|
||||
# requests a distance greater than this value it will cause an error
|
||||
# to be returned. The default is 50mm.
|
||||
#max_extrude_only_velocity:
|
||||
# Maximum velocity (in mm/s) of the extruder motor for extrude only
|
||||
# moves. If this is not specified then it is calculated to match the
|
||||
# limit an XY printing move with a max_extrude_cross_section
|
||||
# extrusion would have.
|
||||
#max_extrude_only_accel:
|
||||
# Maximum acceleration (in mm/s^2) of the extruder motor for extrude
|
||||
# only moves. If this is not specified then it is calculated to
|
||||
# match the limit an XY printing move with a
|
||||
# max_extrude_cross_section extrusion would have.
|
||||
# Maximum velocity (in mm/s) and acceleration (in mm/s^2) of the
|
||||
# extruder motor for retractions and extrude-only moves. These
|
||||
# settings do not place any limit on normal printing moves. If not
|
||||
# specified then they are calculated to match the limit an XY
|
||||
# printing move with a max_extrude_cross_section extrusion would
|
||||
# have.
|
||||
#pressure_advance: 0.0
|
||||
# The amount of raw filament to push into the extruder during
|
||||
# extruder acceleration. An equal amount of filament is retracted
|
||||
|
|
Loading…
Reference in New Issue