config: Add configuration for Modix Big60 printer (#4986)
Signed-off-by: Gabriel Smolnycki <gabjsmo0@gmail.com>
This commit is contained in:
parent
62cfc2527f
commit
e7ba140337
|
@ -0,0 +1,246 @@
|
|||
# Klipper configuration for Modix Big60 w/ Duet 2 Wifi
|
||||
# Dual Volcano hotends, PT100 RTDs, BLtouch
|
||||
|
||||
# Klipper should be compiled for SAM4E8E for this printer.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
||||
# Printer configuration
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_sam4e8e_1234567890-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 160
|
||||
max_accel: 1000
|
||||
max_z_velocity: 6
|
||||
max_z_accel: 120
|
||||
|
||||
[gcode_arcs]
|
||||
resolution: 0.1
|
||||
|
||||
[pause_resume]
|
||||
recover_velocity: 50
|
||||
|
||||
|
||||
# Axis configuration
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PD6
|
||||
dir_pin: PD11
|
||||
enable_pin: !PC6
|
||||
microsteps: 256
|
||||
rotation_distance: 32
|
||||
endstop_pin: ^PC14
|
||||
position_endstop: 0
|
||||
position_min: 0
|
||||
position_max: 600
|
||||
homing_speed: 50
|
||||
second_homing_speed: 2
|
||||
homing_retract_dist: 5
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PD7
|
||||
dir_pin: !PD12
|
||||
enable_pin: !PC6
|
||||
microsteps: 256
|
||||
rotation_distance: 32
|
||||
endstop_pin: ^PA2
|
||||
position_endstop: 600
|
||||
position_min: 0
|
||||
position_max: 600
|
||||
homing_speed: 50
|
||||
second_homing_speed: 2
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: True
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PD8
|
||||
dir_pin: !PD13
|
||||
enable_pin: !PC6
|
||||
microsteps: 256
|
||||
rotation_distance: 1.6000
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -5
|
||||
position_max: 660
|
||||
homing_speed: 2.5
|
||||
second_homing_speed: 1
|
||||
homing_retract_dist: 5
|
||||
|
||||
[extruder]
|
||||
step_pin: PD5
|
||||
dir_pin: PA1
|
||||
enable_pin: !PC6
|
||||
microsteps: 256
|
||||
rotation_distance: 22.9344
|
||||
gear_ratio: 66:22
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: !PA20
|
||||
sensor_type: MAX31865
|
||||
spi_bus: usart0
|
||||
sensor_pin: PB2
|
||||
rtd_nominal_r: 100
|
||||
rtd_reference_r: 400
|
||||
rtd_num_of_wires: 2
|
||||
rtd_use_50Hz_filter: True
|
||||
control: pid
|
||||
pid_kp: 22.2
|
||||
pid_ki: 1.08
|
||||
pid_kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
|
||||
[extruder1]
|
||||
step_pin: PD4
|
||||
dir_pin: !PD9
|
||||
enable_pin: !PC6
|
||||
microsteps: 256
|
||||
rotation_distance: 22.9344
|
||||
gear_ratio: 66:22
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: !PA16
|
||||
sensor_type: MAX31865
|
||||
spi_bus: usart0
|
||||
sensor_pin: PC18
|
||||
rtd_nominal_r: 100
|
||||
rtd_reference_r: 400
|
||||
rtd_num_of_wires: 2
|
||||
rtd_use_50Hz_filter: True
|
||||
control: pid
|
||||
pid_kp: 22.2
|
||||
pid_ki: 1.08
|
||||
pid_kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 400
|
||||
|
||||
|
||||
# Stepper driver configuration
|
||||
|
||||
[tmc2660 stepper_x]
|
||||
cs_pin: PD14
|
||||
spi_speed: 2000000
|
||||
spi_bus: usart1
|
||||
run_current: 1.600
|
||||
sense_resistor: 0.051
|
||||
|
||||
[tmc2660 stepper_y]
|
||||
cs_pin: PC9
|
||||
spi_speed: 2000000
|
||||
spi_bus: usart1
|
||||
run_current: 1.200
|
||||
sense_resistor: 0.051
|
||||
|
||||
[tmc2660 stepper_z]
|
||||
cs_pin: PC10
|
||||
spi_speed: 2000000
|
||||
spi_bus: usart1
|
||||
run_current: 2.400
|
||||
sense_resistor: 0.051
|
||||
|
||||
[tmc2660 extruder]
|
||||
cs_pin: PC17
|
||||
spi_speed: 2000000
|
||||
spi_bus: usart1
|
||||
run_current: 1.200
|
||||
sense_resistor: 0.051
|
||||
|
||||
[tmc2660 extruder1]
|
||||
cs_pin: PC25
|
||||
spi_speed: 2000000
|
||||
spi_bus: usart1
|
||||
run_current: 1.200
|
||||
sense_resistor: 0.051
|
||||
|
||||
|
||||
# Fans
|
||||
|
||||
[fan]
|
||||
pin: PC23
|
||||
|
||||
|
||||
# Filament sensors
|
||||
|
||||
[filament_switch_sensor e0_sensor]
|
||||
pause_on_runout: True
|
||||
switch_pin: PD10
|
||||
runout_gcode:
|
||||
PAUSE_PARK
|
||||
|
||||
[filament_switch_sensor e1_sensor]
|
||||
pause_on_runout: True
|
||||
switch_pin: PC16
|
||||
runout_gcode:
|
||||
PAUSE_PARK
|
||||
|
||||
|
||||
# Bed leveling
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: PC1
|
||||
control_pin: PC3
|
||||
x_offset: -14
|
||||
y_offset: 21
|
||||
z_offset: 2.000
|
||||
speed: 1
|
||||
lift_speed: 5
|
||||
|
||||
[bed_mesh]
|
||||
mesh_min: 25, 25
|
||||
mesh_max: 595, 585
|
||||
probe_count: 11, 11
|
||||
speed: 200
|
||||
horizontal_move_z: 5
|
||||
mesh_pps: 2,2
|
||||
algorithm: bicubic
|
||||
bicubic_tension: 0.15
|
||||
fade_start: 0.5
|
||||
fade_end: 2.5
|
||||
relative_reference_index: 60
|
||||
|
||||
[bed_screws]
|
||||
screw1: 0,0
|
||||
screw1_name: Front Left
|
||||
screw2: 600,0
|
||||
screw2_name: Front Right
|
||||
screw3: 600,600
|
||||
screw3_name: Rear Right
|
||||
screw4: 0,600
|
||||
screw4_name: Rear Left
|
||||
horizontal_move_z: 5
|
||||
probe_height: 0
|
||||
speed: 100
|
||||
probe_speed: 5
|
||||
|
||||
|
||||
# Safe homing
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 310,305
|
||||
speed: 100
|
||||
z_hop: 10
|
||||
z_hop_speed: 5
|
||||
move_to_previous: True
|
||||
|
||||
|
||||
# Macros
|
||||
|
||||
[gcode_macro T0]
|
||||
gcode:
|
||||
ACTIVATE_EXTRUDER EXTRUDER=extruder
|
||||
SET_GCODE_OFFSET Y=0
|
||||
|
||||
[gcode_macro T1]
|
||||
gcode:
|
||||
ACTIVATE_EXTRUDER EXTRUDER=extruder1
|
||||
SET_GCODE_OFFSET Y=-51.5
|
||||
|
||||
[gcode_macro PAUSE_PARK]
|
||||
gcode:
|
||||
G91
|
||||
G0 Z5 F120
|
||||
G90
|
||||
G0 X50 Y50 F3000
|
|
@ -107,6 +107,7 @@ CONFIG ../../config/generic-duet2-maestro.cfg
|
|||
DICTIONARY sam4e8e.dict
|
||||
CONFIG ../../config/generic-duet2.cfg
|
||||
CONFIG ../../config/generic-duet2-duex.cfg
|
||||
CONFIG ../../config/printer-modix-big60-2020.cfg
|
||||
|
||||
# Printers using the samd51
|
||||
DICTIONARY samd51p20.dict
|
||||
|
|
Loading…
Reference in New Issue