3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

config: Update printer-sunlu-t3-2022.cfg (#6040) 

Fix filament sensor and remove unneeded config changes in extruder

The filament sensor on the printer used for initial testing had been removed prior to flashing klipper to it. Only a basic test to see it if triggered or not was preformed. It was discovered by someone else doing some testing on another printer that it would frequently pause. This was a simple oversight, assuming it was a runout switch.

Removed section of config related to filament runout switch and replaced with basic config for filament motion so they printer will simply pause when no more motion is detected. Also notated to add CLEAR_PAUSE to start gcode if using this sensor as it will trigger a paused state when loading or unloading filament. If printer is in a paused state at the start of the print, the attempt to pause will cause the printer to rapidly pause and unpause itself.

Removed min_extruder_temp and max_extrude_only_distance from the extruder section, as they were there only for macros on a test system that is not put into this sample config

Signed-off-by: Zachary Welvaert <zwelvaert@gmail.com>
This commit is contained in:
dahliamoth 2023-02-28 11:41:02 -06:00 committed by GitHub
parent a5fb20765e
commit e6ef48cdf7
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
1 changed files with 13 additions and 14 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

27
config/printer-sunlu-t3-2022.cfg
View File

@ -20,7 +20,7 @@
[mcu]
#obtain your MCU id using ls /dev/serial/by-path/*
serial: dev/serial/by-id/usb-Klipper_stm32f103xe_833E31383534300530343833-if00
serial: dev/serial/by-id/usb-Klipper_stm32f103xe_00000000000
[printer]
kinematics: cartesian
@ -37,7 +37,7 @@ sensor_pin: PC14
control_pin: PA1
x_offset: -28.45
y_offset: 4
z_offset: 1.915 #recheck you own
z_offset: 1.915
pin_up_touch_mode_reports_triggered: FALSE #needed bc of the bltouch clone used by sunlu
[safe_z_home]
@ -66,13 +66,14 @@ screw3_name: Rear Right
screw4: 31,204 #X,Y Position
screw4_name: Rear Left
[filament_switch_sensor Filament_Runout]
pause_on_runout: True
#runout_gcode:
#insert_gcode:
event_delay: 3.0
pause_delay: 5
switch_pin: !PC15 #if reads runout when loaded remove !
##IMPORTANT. If using the filament sensor add CLEAR_PAUSE to your slicer's start gcode or to your print start macro.##
##The act of loading and unloading filament will trigger a paused state##
[filament_motion_sensor Filament_Sensor]
detection_length: 7.0
extruder: extruder
switch_pin: !PC15
pause_on_runout: FALSE
runout_gcode: PAUSE
#########################################################
# Motion Axis
@ -118,18 +119,16 @@ step_pin: PB3
dir_pin: !PB4
enable_pin: !PD2
microsteps: 16
rotation_distance: 23.18840579710145 #verify your own
rotation_distance: 23.18840579710145
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
control: pid
pid_Kp: 19.479 #calibrate your own PID
pid_Kp: 19.479
pid_Ki: 1.073
pid_Kd: 88.385
min_extrude_temp: 175
max_extrude_only_distance: 400
min_temp: 0
max_temp: 250
@ -138,7 +137,7 @@ heater_pin: PC9
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC3
control: pid
pid_Kp: 62.673 #calibrate your own PID
pid_Kp: 62.673
pid_Ki: 1.530
pid_Kd: 641.619
min_temp: 0