config: Add printer-elegoo-neptune3-pro configuration (#5965)

Adds a configuration for the Elegoo Neptune 3 Pro.

Signed-off-by: Koz Ross <koz.ross@retro-freedom.nz>

config/printer-elegoo-neptune3-pro-2023.cfg

@@ -0,0 +1,126 @@
+# This file contains pin mappings for the stock Elegoo Neptune 3 Pro (ZNP Robin Nano_DW V2.2)
+# To use this config, during "make menuconfig" select the  STM32F401 with a
+# "32KiB bootloader" and serial (on USART1 PA10/PA9) communication.
+
+# Note that the "make flash" command does not work with ZNP Robin boards.
+# After running "make", rename the out/klipper.bin file to out/ZNP_ROBIN_NANO.bin
+# Copy the file out/ZNP_ROBIN_NANO.bin to an SD card formatted to FAT32
+# and then restart the printer with the SD card inserted.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+# Core
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+# Steppers
+
+[stepper_x]
+step_pin: PC12
+dir_pin: PB3
+enable_pin: !PD2
+microsteps: 16
+rotation_distance: 40
+endstop_pin: PA13
+position_min: -5
+position_endstop: -5
+position_max: 235
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC11
+dir_pin: PA15
+enable_pin: !PC10
+microsteps: 16
+rotation_distance: 40
+endstop_pin: PB8
+position_endstop: 0
+position_max: 234
+homing_speed: 50
+
+[stepper_z]
+step_pin: PC7
+dir_pin: !PC9
+enable_pin: !PC8
+microsteps: 16
+rotation_distance: 8
+position_min: -0.8
+endstop_pin: probe:z_virtual_endstop
+position_max: 283
+homing_speed: 10
+
+[probe]
+pin: PA8
+# NOTE: Set this to a value based on your printer and bed.
+z_offset: 0
+x_offset: -28.5
+y_offset: 22
+
+[extruder]
+step_pin: PB10
+dir_pin: PB1
+enable_pin: !PC6
+microsteps: 16
+rotation_distance: 8.42
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA6
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC1
+control: pid
+# NOTE: These settings are for PETG, thus 240C at 30% fan.
+pid_Kp: 26.27
+pid_Ki: 1.607
+pid_Kd: 107.380
+min_temp: 0
+max_temp: 260
+max_extrude_only_distance: 100
+
+[heater_bed]
+heater_pin: PA5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+control: pid
+# NOTE: These settings are for PETG, thus 80C bed temperature.
+pid_Kp: 70.173
+pid_Ki: 1.418
+pid_Kd: 868.388
+min_temp: 0
+max_temp: 100
+
+# Coooling
+
+[fan]
+pin: PA7
+
+[heater_fan hotend_fan]
+pin: PB0
+
+# Rest
+
+# This is put on the FAN3 pin.
+[led top_LEDs]
+white_pin: PB9
+cycle_time: 0.005
+
+[filament_switch_sensor filament_runout_sensor]
+switch_pin: PB4
+
+[safe_z_home]
+home_xy_position: 143.5, 93
+
+[bed_mesh]
+mesh_min: 10, 25
+mesh_max: 205, 220
+probe_count: 6, 6
+algorithm: bicubic
+speed: 100

test/klippy/printers.test

@@ -198,6 +198,7 @@ CONFIG ../../config/printer-twotrees-sapphire-pro-sp-3-2020.cfg
 # Printers using the stm32f401
 DICTIONARY stm32f401.dict
 CONFIG ../../config/printer-artillery-sidewinder-x2-2022.cfg
+CONFIG ../../config/printer-elegoo-neptune3-pro-2023.cfg
 
 # Printers using the stm32f405
 DICTIONARY stm32f405.dict