config: New printer profile for Eryone ER20 and minor update for Eryone Thinker Series (#4491)
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73. Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
This commit is contained in:
parent
698ca1d0ae
commit
dafb74e3ab
|
@ -0,0 +1,185 @@
|
|||
# This file contains common pin mappings for the Eryone ER-20 board
|
||||
# board. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 with a 16KiB HID Bootloader.
|
||||
|
||||
# Extra settings to support BL Touch, Filament Runout sensor and
|
||||
# have setting for fixing GCode errors, these configus can be found on
|
||||
# Eryone's Facebook Group under files.
|
||||
# Facebook like to files: https://www.facebook.com/groups/247271792709370/files
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB15
|
||||
dir_pin: PB14
|
||||
rotation_distance: 40
|
||||
enable_pin: !PD10
|
||||
microsteps: 16
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_endstop: 0
|
||||
position_max: 250
|
||||
homing_speed: 40
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
diag_pin: ^PD8
|
||||
uart_address: 2
|
||||
run_current: 0.6
|
||||
hold_current: 0.3
|
||||
stealthchop_threshold: 999999
|
||||
driver_SGTHRS: 80
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PD14
|
||||
dir_pin: !PD13
|
||||
enable_pin: !PC6
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_min: -9
|
||||
position_endstop: -9
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
diag_pin: ^PD15
|
||||
uart_address: 3
|
||||
run_current: 0.7
|
||||
hold_current: 0.35
|
||||
stealthchop_threshold: 999999
|
||||
driver_SGTHRS: 100
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PC8
|
||||
dir_pin: !PC7
|
||||
enable_pin: !PA8
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_max: 250
|
||||
position_min: -1
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
diag_pin: ^PC9
|
||||
uart_address: 1
|
||||
run_current: 0.7
|
||||
hold_current: 0.35
|
||||
stealthchop_threshold: 999999
|
||||
driver_SGTHRS: 0
|
||||
|
||||
[extruder]
|
||||
step_pin: PE13
|
||||
dir_pin: PE14
|
||||
enable_pin: !PB13
|
||||
microsteps: 16
|
||||
# Stock extruder [200 steps/rot]*[16 steps]/[93 steps/mm]
|
||||
rotation_distance: 34.4
|
||||
nozzle_diameter: 0.4
|
||||
filament_diameter: 1.75
|
||||
max_extrude_only_distance: 150
|
||||
heater_pin: PD11
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC1
|
||||
control: pid
|
||||
pid_kp: 26.11
|
||||
pid_ki: 2.01
|
||||
pid_kd: 85
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC11
|
||||
tx_pin: PC10
|
||||
uart_address: 0
|
||||
run_current: 0.7
|
||||
hold_current: 0.35
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD12
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PC2
|
||||
control: pid
|
||||
pid_kp: 100.12
|
||||
pid_ki: 5
|
||||
pid_kd: 305
|
||||
min_temp: 0
|
||||
max_temp: 100
|
||||
|
||||
[fan]
|
||||
pin: PB5
|
||||
|
||||
[heater_fan nozzle_cooling_fan]
|
||||
pin: PB4
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 1500
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
######################################################################
|
||||
# Probing/Mesh Leveling settings for stock BL Touch.
|
||||
# Please make sure you set the correct values for your offsets.
|
||||
######################################################################
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PA11
|
||||
control_pin: PA12
|
||||
pin_move_time: 0.700
|
||||
x_offset: 34
|
||||
y_offset: 0
|
||||
z_offset: 2.6
|
||||
pin_up_touch_mode_reports_triggered: False
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 5,5
|
||||
z_hop: 5.0
|
||||
z_hop_speed: 5.0
|
||||
|
||||
[bed_mesh]
|
||||
speed: 80
|
||||
mesh_min: 40,20
|
||||
mesh_max: 210,205
|
||||
probe_count: 5,5
|
||||
|
||||
######################################################################
|
||||
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type display
|
||||
######################################################################
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_4
|
||||
sclk_pin: EXP1_5
|
||||
sid_pin: EXP1_3
|
||||
encoder_pins: ^EXP2_3, ^EXP2_5
|
||||
click_pin: ^!EXP1_2
|
||||
#kill_pin: ^!EXP2_8
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
######################################################################
|
||||
# EXP1 / EXP2 (display) pins
|
||||
######################################################################
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE12, EXP1_3=PE10, EXP1_5=PE8, EXP1_7=PB2,
|
||||
EXP1_2=PE11, EXP1_4=PE9, EXP1_6=PE7, EXP1_8=PB1,
|
||||
# EXP2 header
|
||||
EXP2_3=PE4, EXP2_5=PE3
|
||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
|
|
@ -84,7 +84,8 @@ min_temp: 0
|
|||
max_temp: 100
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
|
|
|
@ -155,6 +155,7 @@ CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
|
|||
CONFIG ../../config/printer-creality-ender3max-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender3pro-2020.cfg
|
||||
CONFIG ../../config/printer-creality-ender6-2020.cfg
|
||||
CONFIG ../../config/printer-eryone-er20-2021.cfg
|
||||
CONFIG ../../config/printer-flsun-q5-2020.cfg
|
||||
CONFIG ../../config/printer-flsun-qqs-2020.cfg
|
||||
CONFIG ../../config/printer-fokoos-odin5-f3-2021.cfg
|
||||
|
|
Loading…
Reference in New Issue