config: Generic board BIGTREETECH SKR V.1.3 config
Signed-off-by: Aleksander Sobolewski <aleks.sobolewski@outlook.com> Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
1c56ba0ca7
commit
ccc1107dbe
|
@ -0,0 +1,156 @@
|
|||
# This file contains common pin mappings for the BIGTREETECH SKR V1.3
|
||||
# board. To use this config, the firmware should be compiled for the
|
||||
# LPC176x.
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
|
||||
########################
|
||||
# TMC2208 configuration
|
||||
########################
|
||||
|
||||
# Your SKR 1.3 board is likely to be shipped with lots of jumpers
|
||||
# plugged in, together with some spare ones. In order for board to
|
||||
# work properly, you may need to add/remove some of the jumpers.
|
||||
|
||||
# For TMC2208 UART
|
||||
# 1) Remove all of the jumpers below the stepper drivers
|
||||
# 2) Place jumpers on the red pin headers labeled XUART (XUART, YUART etc.)
|
||||
|
||||
#[tmc2208 stepper_x]
|
||||
#uart_pin: P1.17
|
||||
#microsteps: 16
|
||||
#interpolate: true
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 250
|
||||
|
||||
#[tmc2208 stepper_y]
|
||||
#uart_pin: P1.15
|
||||
#microsteps: 16
|
||||
#run_current: 0.850
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 250
|
||||
|
||||
#[tmc2208 stepper_z]
|
||||
#uart_pin: P1.10
|
||||
#microsteps: 16
|
||||
#run_current: 0.650
|
||||
#hold_current: 0.450
|
||||
#stealthchop_threshold: 30
|
||||
|
||||
#[tmc2208 extruder]
|
||||
#uart_pin: P1.8
|
||||
#microsteps: 16
|
||||
#run_current: 0.800
|
||||
#hold_current: 0.500
|
||||
#stealthchop_threshold: 5
|
||||
|
||||
|
||||
########################
|
||||
# Main configuration
|
||||
########################
|
||||
|
||||
## Basic steppers configuration ##
|
||||
|
||||
[stepper_x]
|
||||
step_pin: P2.2
|
||||
dir_pin: !P2.6
|
||||
enable_pin: !P2.1
|
||||
step_distance: .0125
|
||||
endstop_pin: P1.29
|
||||
position_endstop: 0
|
||||
position_max: 320
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: P0.19
|
||||
dir_pin: !P0.20
|
||||
enable_pin: !P2.8
|
||||
step_distance: .0125
|
||||
endstop_pin: P1.27
|
||||
position_endstop: 0
|
||||
position_max: 300
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: P0.22
|
||||
dir_pin: P2.11
|
||||
enable_pin: !P0.21
|
||||
step_distance: .0025
|
||||
endstop_pin: P1.25
|
||||
position_endstop: 0.5
|
||||
position_max: 400
|
||||
|
||||
## Extruder configuration ##
|
||||
|
||||
[extruder]
|
||||
step_pin: P2.13
|
||||
dir_pin: !P0.11
|
||||
enable_pin: !P2.12
|
||||
step_distance: .010526
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: P2.4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: P0.24
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 260
|
||||
|
||||
## Heatbed configuration ##
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: P2.5
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: P0.23
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
## Additional configuration ##
|
||||
|
||||
[fan]
|
||||
pin: P2.3
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 200
|
||||
max_accel: 2000
|
||||
max_z_velocity: 25
|
||||
max_z_accel: 100
|
||||
|
||||
## RepRapDiscount Full Graphic Smart Controller ##
|
||||
|
||||
#[display]
|
||||
#lcd_type: st7920
|
||||
#cs_pin: P1.19
|
||||
#sclk_pin: P1.20
|
||||
#sid_pin: P1.18
|
||||
#encoder_pins: ^P3.26, ^P3.25
|
||||
#click_pin: ^!P0.28
|
||||
#
|
||||
#[output_pin beeper]
|
||||
#pins: !P1.30
|
||||
|
||||
## RepRapDiscount Smart Controller ##
|
||||
|
||||
#[display]
|
||||
#lcd_type: hd44780
|
||||
#rs_pin: P1.19
|
||||
#e_pin: P1.18
|
||||
#d4_pin: P1.20
|
||||
#d5_pin: P1.21
|
||||
#d6_pin: P1.22
|
||||
#d7_pin: P1.23
|
||||
#encoder_pins: ^P3.26, ^P3.25
|
||||
#click_pin: ^!P0.28
|
||||
#
|
||||
#[output_pin beeper]
|
||||
#pins: !P1.30
|
|
@ -66,6 +66,7 @@ CONFIG ../../config/generic-duet2.cfg
|
|||
DICTIONARY lpc176x.dict
|
||||
CONFIG ../../config/generic-azteeg-x5-mini-v3.cfg
|
||||
CONFIG ../../config/generic-bigtreetech-skr-v1.1.cfg
|
||||
CONFIG ../../config/generic-bigtreetech-skr-v1.3.cfg
|
||||
CONFIG ../../config/generic-re-arm.cfg
|
||||
CONFIG ../../config/generic-smoothieboard.cfg
|
||||
|
||||
|
|
Loading…
Reference in New Issue