config: Add example generic-mks-robin-nano.cfg config
Reported by @thucar. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
8a3233b397
commit
cb414ae914
|
@ -0,0 +1,92 @@
|
||||||
|
# This file contains common pin mappings for MKS Robin Nano (v1.2.004)
|
||||||
|
# boards. To use this config, the firmware should be compiled for the
|
||||||
|
# STM32F103. When running "make menuconfig", enable "extra low-level
|
||||||
|
# configuration setup", select the 28KiB bootloader, disable "USB for
|
||||||
|
# communication", and select USART3 for the "Serial Port".
|
||||||
|
|
||||||
|
# Note that the "make flash" command does not work with MKS Robin
|
||||||
|
# boards. After running "make", run the following command:
|
||||||
|
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano.bin
|
||||||
|
# Copy the file out/Robin_nano.bin to an SD card and then restart the
|
||||||
|
# printer with that SD card.
|
||||||
|
|
||||||
|
# See the example.cfg file for a description of available parameters.
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PE3
|
||||||
|
dir_pin: !PE2
|
||||||
|
enable_pin: !PE4
|
||||||
|
step_distance: .01
|
||||||
|
endstop_pin: !PA15
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 200
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PE0
|
||||||
|
dir_pin: !PB9
|
||||||
|
enable_pin: !PE1
|
||||||
|
step_distance: .01
|
||||||
|
endstop_pin: !PA12
|
||||||
|
position_endstop: 230
|
||||||
|
position_max: 230
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PB5
|
||||||
|
dir_pin: PB4
|
||||||
|
enable_pin: !PB8
|
||||||
|
step_distance: .0025
|
||||||
|
endstop_pin: !PA11
|
||||||
|
position_endstop: 0.5
|
||||||
|
position_max: 200
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PD6
|
||||||
|
dir_pin: !PD3
|
||||||
|
enable_pin: !PB3
|
||||||
|
step_distance: .0021
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PC3
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PC1
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 14.669
|
||||||
|
pid_Ki: 0.572
|
||||||
|
pid_Kd: 94.068
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
#[extruder1]
|
||||||
|
#step_pin: PA6
|
||||||
|
#dir_pin: !PA1
|
||||||
|
#enable_pin: !PA3
|
||||||
|
#heater_pin: PB0
|
||||||
|
#sensor_pin: PC2
|
||||||
|
#...
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PA0
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC0
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 325.10
|
||||||
|
pid_Ki: 63.35
|
||||||
|
pid_Kd: 417.10
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PB1
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/ttyUSB0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: corexy
|
||||||
|
max_velocity: 250
|
||||||
|
max_accel: 4500
|
||||||
|
max_z_velocity: 25
|
||||||
|
max_z_accel: 100
|
|
@ -113,6 +113,7 @@ CONFIG ../../config/generic-bigtreetech-skr-e3-dip.cfg
|
||||||
DICTIONARY stm32f103-serial.dict
|
DICTIONARY stm32f103-serial.dict
|
||||||
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
|
CONFIG ../../config/generic-fysetc-cheetah-v1.1.cfg
|
||||||
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
|
CONFIG ../../config/generic-fysetc-cheetah-v1.2.cfg
|
||||||
|
CONFIG ../../config/generic-mks-robin-nano.cfg
|
||||||
|
|
||||||
# Printers using the stm32f407
|
# Printers using the stm32f407
|
||||||
DICTIONARY stm32f407.dict
|
DICTIONARY stm32f407.dict
|
||||||
|
|
Loading…
Reference in New Issue