3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

docs: Try to be more clear that the "paper test" steps need to be run 

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2019-05-24 22:34:24 -04:00
parent 7792b0f2bb
commit c77285287b
3 changed files with 24 additions and 20 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

15
docs/Delta_Calibrate.md
View File

@ -42,13 +42,14 @@ There are two ways to perform the probing - manual probing
(`DELTA_CALIBRATE`). Automatic probing utilizes a hardware device
capable of triggering when the toolhead is at a set distance from the
bed. The manual probing method will move the head near the bed and
then wait for the user to follow the
["paper test"](Bed_Level.md#the-paper-test) steps. It is recommended
to use manual probing for delta calibration. A number of common
printer kits come with probes that are not sufficiently accurate
(specifically, small differences in arm length can cause effector tilt
which can skew an automatic probe). Manual probing only takes a few
minutes and it eliminates error introduced by the probe.
then wait for the user to follow the steps described at
["the paper test"](Bed_Level.md#the-paper-test) to determine the
actual distance between the nozzle and bed at the given location. It
is recommended to use manual probing for delta calibration. A number
of common printer kits come with probes that are not sufficiently
accurate (specifically, small differences in arm length can cause
effector tilt which can skew an automatic probe). Manual probing only
takes a few minutes and it eliminates error introduced by the probe.
To perform the basic probe, make sure the config has a
[delta_calibrate] section defined and run:

8
docs/Manual_Level.md
View File

@ -17,9 +17,11 @@ terminal tab, and run:
```
Z_ENDSTOP_CALIBRATE
```
Then perform the ["paper test"](Bed_Level.md#the-paper-test) steps to
determine the actual height at the given position. One can then
`ACCEPT` the position and save the results to the config file with:
Then follow the steps described at
["the paper test"](Bed_Level.md#the-paper-test) to determine the
actual distance between the nozzle and bed at the given location. Once
those steps are complete one can `ACCEPT` the position and save the
results to the config file with:
```
SAVE_CONFIG
```

21
docs/Probe_Calibrate.md
View File

@ -53,14 +53,15 @@ tool.
This tool will perform an automatic probe, then lift the head, move
the nozzle over the location of the probe point, and start the manual
probe tool. Once the manual probe tool starts, perform the
["paper test"](Bed_Level.md#the-paper-test) to determine the actual
nozzle height at the given point.
probe tool. If the nozzle does not move to a position above the
automatic probe point, then `ABORT` the manual probe tool and perform
the XY probe offset calibration described above.
If the nozzle does not move to a position above the probe point, then
`ABORT` the manual probe tool and perform the XY probe offset
calibration described above.
After completing the "paper test", use the `ACCEPT` command to
accept the current Z height and then use the `SAVE_CONFIG` command to
save the given probe z_offset to the config file.
Once the manual probe tool starts, follow the steps described at
["the paper test"](Bed_Level.md#the-paper-test)) to determine the
actual distance between the nozzle and bed at the given location. Once
those steps are complete one can `ACCEPT` the position and save the
results to the config file with:
```
SAVE_CONFIG
```