From c2d3a1689e71788fd4c98b863ea1ad037a8592fc Mon Sep 17 00:00:00 2001 From: Kevin O'Connor Date: Thu, 23 Sep 2021 19:45:22 -0400 Subject: [PATCH] config: Remove URLs to github repository Update URLs to documentation in the github repository to use the klipper3d.org website. Signed-off-by: Kevin O'Connor --- config/kit-voron2-250mm.cfg | 3 --- config/printer-creality-ender3max-2021.cfg | 4 ++-- config/printer-hiprecy-leo-2019.cfg | 2 +- config/printer-wanhao-duplicator-i3-v2.1-2017.cfg | 6 +++--- 4 files changed, 6 insertions(+), 9 deletions(-) diff --git a/config/kit-voron2-250mm.cfg b/config/kit-voron2-250mm.cfg index dcad007a..2d509967 100644 --- a/config/kit-voron2-250mm.cfg +++ b/config/kit-voron2-250mm.cfg @@ -13,9 +13,6 @@ # See docs/Config_Reference.md for a description of parameters. -# AND PLEASE READ THROUGH THE KLIPPER DOCUMENTATION FIRST! -# https://github.com/KevinOConnor/klipper/tree/master/docs - # *** THINGS TO CHANGE/CHECK: *** # Arduino paths [mcu] section # Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file diff --git a/config/printer-creality-ender3max-2021.cfg b/config/printer-creality-ender3max-2021.cfg index 7c1cb242..5e51685d 100644 --- a/config/printer-creality-ender3max-2021.cfg +++ b/config/printer-creality-ender3max-2021.cfg @@ -98,7 +98,7 @@ step_pin: PB4 dir_pin: PB3 enable_pin: !PC3 microsteps: 16 -rotation_distance: 31.901 # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md +rotation_distance: 31.901 # Calibrate - see https://www.klipper3d.org/Rotation_Distance.html nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PA1 @@ -110,7 +110,7 @@ pid_Ki: 1.063 pid_Kd: 108.982 min_temp: 0 max_temp: 250 -pressure_advance: 0.0 # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Pressure_Advance.md +pressure_advance: 0.0 # Calibrate - see https://www.klipper3d.org/Pressure_Advance.html [heater_bed] diff --git a/config/printer-hiprecy-leo-2019.cfg b/config/printer-hiprecy-leo-2019.cfg index 5fdff67a..6313842f 100644 --- a/config/printer-hiprecy-leo-2019.cfg +++ b/config/printer-hiprecy-leo-2019.cfg @@ -49,7 +49,7 @@ step_pin: PA4 dir_pin: PA6 enable_pin: !PA2 microsteps: 16 -rotation_distance: 23.133 ### Based on default 415 steps/mm. See https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md for fine tuning +rotation_distance: 23.133 ### Based on default 415 steps/mm. See https://www.klipper3d.org/Rotation_Distance.html for fine tuning gear_ratio: 50:17 nozzle_diameter: 0.400 filament_diameter: 1.750 diff --git a/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg b/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg index 8f2fd7ef..211229e2 100644 --- a/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg +++ b/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg @@ -18,7 +18,7 @@ # guidelines: # # - Locate the USB serial port for your printer in /dev/serial/by-id/ format. -# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#wheres-my-serial-port +# See https://www.klipper3d.org/FAQ.html#wheres-my-serial-port # It will be something like: # /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_ABCD1234-if00-port0 # @@ -27,7 +27,7 @@ # - At this point, "make flash FLASH_DEVICE=..." should successfully # flash your printer board. Use the /dev/serial/by-id/ format for # FLASH_DEVICE to ensure consistent results. -# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#the-make-flash-command-doesnt-work +# See https://www.klipper3d.org/FAQ.html#the-make-flash-command-doesnt-work # if you have problems. # # - Copy this sample file you are currently reading to ~/printer.cfg, @@ -83,7 +83,7 @@ # You should then see a status screen appear on the printer's LCD. # # - Be sure to follow these instructions before attempting any prints: -# https://github.com/KevinOConnor/klipper/blob/master/docs/Config_checks.md +# https://www.klipper3d.org/Config_checks.html [stepper_x] step_pin: PD7