diff --git a/config/kit-voron2-250mm.cfg b/config/kit-voron2-250mm.cfg
index dcad007a..2d509967 100644
--- a/config/kit-voron2-250mm.cfg
+++ b/config/kit-voron2-250mm.cfg
@@ -13,9 +13,6 @@
 
 # See docs/Config_Reference.md for a description of parameters.
 
-# AND PLEASE READ THROUGH THE KLIPPER DOCUMENTATION FIRST!
-# https://github.com/KevinOConnor/klipper/tree/master/docs
-
 # *** THINGS TO CHANGE/CHECK: ***
 # Arduino paths                         [mcu] section
 # Thermistor types                      [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
diff --git a/config/printer-creality-ender3max-2021.cfg b/config/printer-creality-ender3max-2021.cfg
index 7c1cb242..5e51685d 100644
--- a/config/printer-creality-ender3max-2021.cfg
+++ b/config/printer-creality-ender3max-2021.cfg
@@ -98,7 +98,7 @@ step_pin: PB4
 dir_pin: PB3
 enable_pin: !PC3
 microsteps: 16
-rotation_distance: 31.901           # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md
+rotation_distance: 31.901           # Calibrate - see https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 filament_diameter: 1.750
 heater_pin: PA1
@@ -110,7 +110,7 @@ pid_Ki: 1.063
 pid_Kd: 108.982
 min_temp: 0
 max_temp: 250
-pressure_advance: 0.0               # Calibrate - see https://github.com/KevinOConnor/klipper/blob/master/docs/Pressure_Advance.md
+pressure_advance: 0.0               # Calibrate - see https://www.klipper3d.org/Pressure_Advance.html
 
 
 [heater_bed]
diff --git a/config/printer-hiprecy-leo-2019.cfg b/config/printer-hiprecy-leo-2019.cfg
index 5fdff67a..6313842f 100644
--- a/config/printer-hiprecy-leo-2019.cfg
+++ b/config/printer-hiprecy-leo-2019.cfg
@@ -49,7 +49,7 @@ step_pin: PA4
 dir_pin: PA6
 enable_pin: !PA2
 microsteps: 16
-rotation_distance: 23.133 ### Based on default 415 steps/mm. See https://github.com/KevinOConnor/klipper/blob/master/docs/Rotation_Distance.md for fine tuning
+rotation_distance: 23.133 ### Based on default 415 steps/mm. See https://www.klipper3d.org/Rotation_Distance.html for fine tuning
 gear_ratio: 50:17
 nozzle_diameter: 0.400
 filament_diameter: 1.750
diff --git a/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg b/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg
index 8f2fd7ef..211229e2 100644
--- a/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg
+++ b/config/printer-wanhao-duplicator-i3-v2.1-2017.cfg
@@ -18,7 +18,7 @@
 # guidelines:
 #
 # - Locate the USB serial port for your printer in /dev/serial/by-id/ format.
-#   See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#wheres-my-serial-port
+#   See https://www.klipper3d.org/FAQ.html#wheres-my-serial-port
 #   It will be something like:
 #   /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_ABCD1234-if00-port0
 #
@@ -27,7 +27,7 @@
 # - At this point, "make flash FLASH_DEVICE=..." should successfully
 #   flash your printer board. Use the /dev/serial/by-id/ format for
 #   FLASH_DEVICE to ensure consistent results.
-#   See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#the-make-flash-command-doesnt-work
+#   See https://www.klipper3d.org/FAQ.html#the-make-flash-command-doesnt-work
 #   if you have problems.
 #
 # - Copy this sample file you are currently reading to ~/printer.cfg,
@@ -83,7 +83,7 @@
 #   You should then see a status screen appear on the printer's LCD.
 #
 # - Be sure to follow these instructions before attempting any prints:
-#   https://github.com/KevinOConnor/klipper/blob/master/docs/Config_checks.md
+#   https://www.klipper3d.org/Config_checks.html
 
 [stepper_x]
 step_pin: PD7