config: Config for Monoprice Select Mini v1 (#5243)
Signed-off-by: Jace Wiseman <jwiseman@gmail.com>
This commit is contained in:
jace
GitHub
parent
c8cc2a1e27
commit
c27a9182f3
|
|
@ -0,0 +1,141 @@
|
|||
# This file contains common pin mappings for the Monoprice
|
||||
# Select Mini v1. To use this config, the firmware should be compiled for the
|
||||
# STM32F103 microcontroller with an 8MHz crystal and USB for communication.
|
||||
#
|
||||
# Use the following settings in make menuconfig:
|
||||
#
|
||||
# * Enable extra low-level configuration options: Enable
|
||||
# * Microcontroller architecture: STM32
|
||||
# * Processor: STM32F103
|
||||
# * Bootloader offset: 8KiB bootloader
|
||||
# * Clockspeed: 8 Mhz crystal
|
||||
# * Communication interface: USB (on PA11/PA12)
|
||||
# * GPIO pins to set: PA8, PB1, PB11, PB9
|
||||
#
|
||||
# IMPORTANT: A bootloader offset of 8KiB will preserver the stock bootloader
|
||||
# and allows easy flashing via SDCard without additional hardware.
|
||||
#
|
||||
# IMPORTANT: Setting PB9 in the the GPIO pins to set at micro-controller
|
||||
# startup is required for the USB port to function.
|
||||
#
|
||||
# PA8, PB1, PB11 in the GPIO pins deactivates the steppers until klippy
|
||||
# takes over.
|
||||
#
|
||||
# Note 1: Prior to flashing klipper, if possible, make a copy of the default
|
||||
# or current configuration values for the printer. Running an M503 command
|
||||
# will output these values.
|
||||
#
|
||||
# Note 2: Klipper can be flashed by copying out/klipper.bin to the MPSMv1's
|
||||
# SDCard, renaming it to update.bin, and creating an empty file on the SD card
|
||||
# named fcupdate.flg. Insert the SDCard while the printer is off it on. After
|
||||
# klipper is flashed, remove the SDCard and delete update.bin and fcupdate.flg
|
||||
# to prevent the firmware from flashing on every subsequent power-on.
|
||||
# Returning to stock firmware without a programmer is possible as long as the
|
||||
# bootloader is not overwritten.
|
||||
#
|
||||
# Note 3: Stepper directions are not consistent in MSPMv1 printers. Check the
|
||||
# directions of the printer with M503 in the stock firmware and adjust the
|
||||
# dir_pins below accordingly.
|
||||
#
|
||||
# Note 4: Klipper currently does not support the LCD-UI of this
|
||||
# printer, which is connected via serial interface and controlled by an
|
||||
# esp8266 using a custom protocol.
|
||||
#
|
||||
# See ../docs/Config_Reference.md file for a description of all parameters.
|
||||
|
||||
[stepper_x]
|
||||
homing_speed: 15
|
||||
step_pin: PB14
|
||||
dir_pin: !PB15 # modify stepper direction if necessary
|
||||
enable_pin: !PA8
|
||||
# rotation_distance varies in the printer model. Check the correct
|
||||
# step-rate of the Select Mini in the original firmware (with M503)
|
||||
# and calculate the appropriate value for rotation_distance. This has
|
||||
# to be done for all axes.
|
||||
microsteps: 16
|
||||
rotation_distance: 34.510 # 17 teeth on pulley; MXL belt (2.03 pitch)
|
||||
endstop_pin: ^!PB4
|
||||
position_endstop: 0
|
||||
position_max: 120 # default bed width
|
||||
position_min: 0
|
||||
|
||||
[stepper_y]
|
||||
homing_speed: 15
|
||||
step_pin: PB12
|
||||
dir_pin: PB13 # modify stepper direction if necessary
|
||||
enable_pin: !PA8
|
||||
microsteps: 16
|
||||
rotation_distance: 34.510 # check comment in [stepper_x] section
|
||||
endstop_pin: ^!PA15
|
||||
position_endstop: 0
|
||||
position_max: 120 # default bed length
|
||||
position_min: 0
|
||||
|
||||
[stepper_z]
|
||||
homing_speed: 10
|
||||
step_pin: PB10
|
||||
dir_pin: PB2 # modify stepper direction if necessary
|
||||
enable_pin: !PB11
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 48
|
||||
rotation_distance: 0.7 # M4 rod. check comment in [stepper_x] section
|
||||
endstop_pin: ^!PB5
|
||||
position_endstop: 0.5
|
||||
position_max: 120 # default height
|
||||
|
||||
[extruder]
|
||||
# extruder stepper
|
||||
step_pin: PB0
|
||||
dir_pin: !PC13 # modify stepper direction if necessary
|
||||
enable_pin: !PB1
|
||||
microsteps: 16
|
||||
rotation_distance: 32.990 # 97 steps/mm. check comment in [stepper_x] section
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
# heater
|
||||
heater_pin: PB6
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA0
|
||||
control: pid
|
||||
pid_kp: 20.00
|
||||
pid_ki: 0.02
|
||||
pid_kd: 250.00
|
||||
# temperatures
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
max_extrude_only_distance: 425 #for (un-)loading
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PB7
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PA1
|
||||
control: pid
|
||||
pid_kp: 70.00
|
||||
pid_ki: 1.50
|
||||
pid_kd: 812.00
|
||||
min_temp: 0
|
||||
max_temp: 85
|
||||
|
||||
# Print cooling fan
|
||||
[heater_fan hotend_fan]
|
||||
pin: PB8
|
||||
heater: extruder
|
||||
heater_temp: 45.0
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyACM0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 150
|
||||
max_accel: 800
|
||||
max_z_velocity: 1.5
|
||||
max_z_accel: 20
|
||||
|
||||
# Positions for BED_SCREWS_ADJUST levelling with bed screws still accessible
|
||||
[bed_screws]
|
||||
screw1: 22, 10
|
||||
screw2: 22, 90
|
||||
screw3: 98, 90
|
||||
screw4: 98, 10
|
||||
Loading…
Reference in New Issue