config: Add generic-bigtreetech-skr-e3-dip.cfg config
Reported by @salimvanak. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
40d076cce5
commit
b91993d6a4
|
@ -0,0 +1,168 @@
|
||||||
|
# This file contains common pin mappings for the BIGTREETECH SKR E3
|
||||||
|
# DIP. To use this config, the firmware should be compiled for the
|
||||||
|
# STM32F103 with a "28KiB bootloader". Also, select "Enable extra
|
||||||
|
# low-level configuration options" and configure "GPIO pins to set at
|
||||||
|
# micro-controller startup" to "!PC13".
|
||||||
|
|
||||||
|
# The "make flash" command does not work on the SKR E3 DIP. Instead,
|
||||||
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||||
|
# file named "firmware.bin" on an SD card and then restart the SKR E3
|
||||||
|
# DIP with that SD card.
|
||||||
|
|
||||||
|
# See the example.cfg file for a description of available parameters.
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PC6
|
||||||
|
dir_pin: !PB15
|
||||||
|
enable_pin: !PC7
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PC1
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PB13
|
||||||
|
dir_pin: !PB12
|
||||||
|
enable_pin: !PB14
|
||||||
|
step_distance: .0125
|
||||||
|
endstop_pin: ^PC0
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PB10
|
||||||
|
dir_pin: PB2
|
||||||
|
enable_pin: !PB11
|
||||||
|
step_distance: .0025
|
||||||
|
endstop_pin: ^PC15
|
||||||
|
position_endstop: 0.0
|
||||||
|
position_max: 250
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PB0
|
||||||
|
dir_pin: !PC5
|
||||||
|
enable_pin: !PB1
|
||||||
|
step_distance: 0.010526
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PC8
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PA0
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 21.527
|
||||||
|
pid_Ki: 1.063
|
||||||
|
pid_Kd: 108.982
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PC9
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PC3
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 54.027
|
||||||
|
pid_Ki: 0.770
|
||||||
|
pid_Kd: 948.182
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PA8
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
[static_digital_output usb_pullup_enable]
|
||||||
|
pins: !PC13
|
||||||
|
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# TMC2208 configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
|
#[tmc2208 stepper_x]
|
||||||
|
#uart_pin: PC10
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 250
|
||||||
|
|
||||||
|
#[tmc2208 stepper_y]
|
||||||
|
#uart_pin: PC11
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 250
|
||||||
|
|
||||||
|
#[tmc2208 stepper_z]
|
||||||
|
#uart_pin: PC12
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 30
|
||||||
|
|
||||||
|
#[tmc2208 extruder]
|
||||||
|
#uart_pin: PD2
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.650
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 5
|
||||||
|
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# TMC2130 configuration
|
||||||
|
########################################
|
||||||
|
|
||||||
|
#[tmc2130 stepper_x]
|
||||||
|
#cs_pin: PC10
|
||||||
|
#spi_bus: spi3
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 250
|
||||||
|
|
||||||
|
#[tmc2130 stepper_y]
|
||||||
|
#cs_pin: PC11
|
||||||
|
#spi_bus: spi3
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 250
|
||||||
|
|
||||||
|
#[tmc2130 stepper_z]
|
||||||
|
#cs_pin: PC12
|
||||||
|
#spi_bus: spi3
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.580
|
||||||
|
#hold_current: 0.450
|
||||||
|
#stealthchop_threshold: 30
|
||||||
|
|
||||||
|
#[tmc2130 extruder]
|
||||||
|
#cs_pin: PD2
|
||||||
|
#spi_bus: spi3
|
||||||
|
#microsteps: 16
|
||||||
|
#run_current: 0.650
|
||||||
|
#hold_current: 0.500
|
||||||
|
#stealthchop_threshold: 5
|
||||||
|
|
||||||
|
|
||||||
|
########################################
|
||||||
|
# EXP1 / EXP2 (display) pins
|
||||||
|
########################################
|
||||||
|
|
||||||
|
[board_pins]
|
||||||
|
aliases:
|
||||||
|
# EXP1 header
|
||||||
|
EXP1_1=PA15, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
|
||||||
|
EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PB7, EXP1_10=<5V>
|
||||||
|
|
||||||
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
@ -87,6 +87,7 @@ DICTIONARY stm32f1.dict
|
||||||
CONFIG ../../config/generic-bigtreetech-skr-mini.cfg
|
CONFIG ../../config/generic-bigtreetech-skr-mini.cfg
|
||||||
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v1.0.cfg
|
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v1.0.cfg
|
||||||
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v1.2.cfg
|
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v1.2.cfg
|
||||||
|
CONFIG ../../config/generic-bigtreetech-skr-e3-dip.cfg
|
||||||
|
|
||||||
# Printers using the stm32f103 via serial
|
# Printers using the stm32f103 via serial
|
||||||
DICTIONARY stm32f1-serial.dict
|
DICTIONARY stm32f1-serial.dict
|
||||||
|
|
Loading…
Reference in New Issue