config: Elegoo Neptune 2 configuration (#4592)

Signed-off-by: Willie Sippel <wsippel@me.com>
This commit is contained in:
wsippel 2021-08-31 19:07:33 +02:00 committed by GitHub
parent dcf8cb82a3
commit b9116e4a03
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
1 changed files with 103 additions and 0 deletions

View File

@ -0,0 +1,103 @@
# This file contains common pin mappings for the stock Elegoo
# Neptune 2 with a MKS Robin Nano (v1.2.004) board. To use this
# config, the firmware should be compiled for the STM32F103. When
# running "make menuconfig", enable "extra low-level configuration
# setup", select the 28KiB bootloader, and serial (on # USART3
# PB11/PB10) communication.
# Note that the "make flash" command does not work with MKS Robin
# boards. After running "make", run the following command:
# ./scripts/update_mks_robin.py out/klipper.bin out/elegoo.bin
# Copy the file out/elegoo.bin to an SD card and then restart the
# printer with that SD card.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PE3
dir_pin: PE2
enable_pin: !PE4
microsteps: 16
rotation_distance: 40
endstop_pin: PA15
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_y]
step_pin: PE0
dir_pin: PB9
enable_pin: !PE1
microsteps: 16
rotation_distance: 40
endstop_pin: PA12
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_z]
step_pin: PB5
dir_pin: !PB4
enable_pin: !PB8
microsteps: 16
rotation_distance: 8
endstop_pin: PA11
position_endstop: 0.0
position_max: 250
[extruder]
max_extrude_only_distance: 100.0
step_pin: PD6
dir_pin: PD3
enable_pin: !PB3
microsteps: 16
rotation_distance: 34.406
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PC3
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC1
# tuned for stock hardware with 210 degree Celsius target
pid_Kp: 29.056
pid_Ki: 1.628
pid_Kd: 129.664
min_temp: 0
max_temp: 250
[filament_switch_sensor filament_sensor]
pause_on_runout: True
switch_pin: PA4
[heater_bed]
heater_pin: PA0
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC0
# tuned for stock hardware with 60 degree Celsius target
pid_Kp: 70.857
pid_Ki: 1.221
pid_Kd: 1028.316
min_temp: 0
max_temp: 130
[heater_fan hotend_fan]
pin: PB0
heater: extruder
heater_temp: 50.0
[fan]
pin: PB1
[mcu]
serial: /dev/ttyUSB0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100
[static_digital_output display_reset]
# the FSMC touchscreen isn't supported, so we'll just disable it
pins: !PC6, !PD13