config: Elegoo Neptune 2 configuration (#4592)
Signed-off-by: Willie Sippel <wsippel@me.com>
This commit is contained in:
parent
dcf8cb82a3
commit
b9116e4a03
|
@ -0,0 +1,103 @@
|
||||||
|
# This file contains common pin mappings for the stock Elegoo
|
||||||
|
# Neptune 2 with a MKS Robin Nano (v1.2.004) board. To use this
|
||||||
|
# config, the firmware should be compiled for the STM32F103. When
|
||||||
|
# running "make menuconfig", enable "extra low-level configuration
|
||||||
|
# setup", select the 28KiB bootloader, and serial (on # USART3
|
||||||
|
# PB11/PB10) communication.
|
||||||
|
|
||||||
|
# Note that the "make flash" command does not work with MKS Robin
|
||||||
|
# boards. After running "make", run the following command:
|
||||||
|
# ./scripts/update_mks_robin.py out/klipper.bin out/elegoo.bin
|
||||||
|
# Copy the file out/elegoo.bin to an SD card and then restart the
|
||||||
|
# printer with that SD card.
|
||||||
|
|
||||||
|
# See docs/Config_Reference.md for a description of parameters.
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
step_pin: PE3
|
||||||
|
dir_pin: PE2
|
||||||
|
enable_pin: !PE4
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: PA15
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
step_pin: PE0
|
||||||
|
dir_pin: PB9
|
||||||
|
enable_pin: !PE1
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 40
|
||||||
|
endstop_pin: PA12
|
||||||
|
position_endstop: 0
|
||||||
|
position_max: 235
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PB5
|
||||||
|
dir_pin: !PB4
|
||||||
|
enable_pin: !PB8
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 8
|
||||||
|
endstop_pin: PA11
|
||||||
|
position_endstop: 0.0
|
||||||
|
position_max: 250
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
max_extrude_only_distance: 100.0
|
||||||
|
step_pin: PD6
|
||||||
|
dir_pin: PD3
|
||||||
|
enable_pin: !PB3
|
||||||
|
microsteps: 16
|
||||||
|
rotation_distance: 34.406
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PC3
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC1
|
||||||
|
# tuned for stock hardware with 210 degree Celsius target
|
||||||
|
pid_Kp: 29.056
|
||||||
|
pid_Ki: 1.628
|
||||||
|
pid_Kd: 129.664
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[filament_switch_sensor filament_sensor]
|
||||||
|
pause_on_runout: True
|
||||||
|
switch_pin: PA4
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PA0
|
||||||
|
sensor_type: EPCOS 100K B57560G104F
|
||||||
|
sensor_pin: PC0
|
||||||
|
# tuned for stock hardware with 60 degree Celsius target
|
||||||
|
pid_Kp: 70.857
|
||||||
|
pid_Ki: 1.221
|
||||||
|
pid_Kd: 1028.316
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
pin: PB0
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PB1
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/ttyUSB0
|
||||||
|
restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: cartesian
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000
|
||||||
|
max_z_velocity: 5
|
||||||
|
max_z_accel: 100
|
||||||
|
|
||||||
|
[static_digital_output display_reset]
|
||||||
|
# the FSMC touchscreen isn't supported, so we'll just disable it
|
||||||
|
pins: !PC6, !PD13
|
Loading…
Reference in New Issue