3diy
/
klipper
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

config: Minor changes to printer-fokoos-odin5-f3-2021.cfg 

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor 2021-05-12 15:01:23 -04:00
parent 93add3a095
commit b4a2229788
1 changed files with 11 additions and 14 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

25
config/printer-fokoos-odin5-f3-2021.cfg
View File

@ -4,6 +4,17 @@
# permanently display "Booting..." after the Klipper firmware is flashed; use # permanently display "Booting..." after the Klipper firmware is flashed; use
# Fluidd, Mainsail, or OctoPrint etc. to control the printer. # Fluidd, Mainsail, or OctoPrint etc. to control the printer.
# To use this config, the firmware should be compiled for the STM32F103. When
# running "make menuconfig", enable "extra low-level configuration setup",
# select the 28KiB bootloader, and serial (on USART3 PB11/PB10) communication.
# Connect the printer to your Raspberry Pi using the printer's USB port.
# Note that the "make flash" command does not work with MKS Robin
# boards. After running "make", run the following command:
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
# printer with that SD card. The firmware will automatically be flashed.
# WARNING: The printer's Z endstop inductive sensor is not very accurate, so # WARNING: The printer's Z endstop inductive sensor is not very accurate, so
# stepper_z:position_endstop has been set to 0.0, for safety, below. This will # stepper_z:position_endstop has been set to 0.0, for safety, below. This will
# prevent the nozzle crashing into the bed when you first home Z. You must # prevent the nozzle crashing into the bed when you first home Z. You must
@ -17,17 +28,6 @@
# This configuration does support the addition of a BLtouch. See below for # This configuration does support the addition of a BLtouch. See below for
# further instructions. # further instructions.
# To use this config, the firmware should be compiled for the STM32F103. When
# running "make menuconfig", enable "extra low-level configuration setup",
# select the 28KiB bootloader, and serial (on USART3 PB11/PB10) communication.
# Connect the printer to your Raspberry Pi using the printer's USB port.
# Note that the "make flash" command does not work with MKS Robin
# boards. After running "make", run the following command:
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
# printer with that SD card. The firmware will automatically be flashed.
# See docs/Config_Reference.md for a description of parameters. # See docs/Config_Reference.md for a description of parameters.
[mcu] [mcu]
@ -130,9 +130,6 @@ pin: PB1
[filament_switch_sensor filament_sensor] [filament_switch_sensor filament_sensor]
switch_pin: !PA4 switch_pin: !PA4
# This is needed if you are using Arc Welder.
[gcode_arcs]
# BLtouch configuration. Uncomment these blocks if you have installed a # BLtouch configuration. Uncomment these blocks if you have installed a
# BLtouch. The correct wiring is to use the Robin Nano's BLtouch port for the # BLtouch. The correct wiring is to use the Robin Nano's BLtouch port for the
# 3-wire connector (make sure you connect it the right way round) and the Z+ # 3-wire connector (make sure you connect it the right way round) and the Z+