config: Add BQ Hephestos printer (#5676)
This is a working config with full LCD and stepper settings (only thing missing is the kill switch, which did not appear to work) Signed-off-by: Rui Carmo <rui.carmo@gmail.com>
This commit is contained in:
parent
6a91824486
commit
b1dcd35b7a
|
@ -0,0 +1,107 @@
|
|||
# This file contains pin mappings for the BQ Prusa i3 Hephestos from 2014
|
||||
# (https://www.reprap.org/wiki/Prusa_i3_Hephestos)
|
||||
# It was sold in kit form, and uses a RAMPS board with HD44780 display without
|
||||
# heated bed or any modern amenities.
|
||||
|
||||
# To use this config, the firmware should be compiled for the AVR atmega2560.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[display]
|
||||
lcd_type: hd44780
|
||||
rs_pin: PH1
|
||||
e_pin: PH0
|
||||
d4_pin: PA1
|
||||
d5_pin: PA3
|
||||
d6_pin: PA5
|
||||
d7_pin: PA7
|
||||
encoder_pins: ^PC4, ^PC6
|
||||
click_pin: ^!PC2
|
||||
kill_pin: ^!PG0
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PF0
|
||||
dir_pin: !PF1
|
||||
enable_pin: !PD7
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PE5
|
||||
position_endstop: 0
|
||||
position_max: 215
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PF6
|
||||
dir_pin: PF7
|
||||
enable_pin: !PF2
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^!PJ1
|
||||
position_endstop: 0
|
||||
position_max: 210
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PL3
|
||||
dir_pin: !PL1
|
||||
enable_pin: !PK0
|
||||
microsteps: 16
|
||||
rotation_distance: 0.8
|
||||
endstop_pin: ^!PD3
|
||||
position_endstop: 0
|
||||
position_max: 200
|
||||
homing_speed: 3
|
||||
|
||||
[extruder]
|
||||
step_pin: PA4
|
||||
dir_pin: PA6
|
||||
enable_pin: !PA2
|
||||
microsteps: 16
|
||||
# measured extruding 100mm of filament with stock Hephestos extruder
|
||||
rotation_distance: 31.825
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PB4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PK5
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
control: pid
|
||||
pid_kp: 19.462
|
||||
pid_ki: 0.713
|
||||
pid_kd: 132.830
|
||||
|
||||
|
||||
# 5 points for manual bed leveling that still leave room for accessing the stock screws
|
||||
[bed_screws]
|
||||
screw1: 40, 40
|
||||
screw2: 180, 40
|
||||
screw3: 180, 160
|
||||
screw4: 40, 160
|
||||
screw5: 110, 100
|
||||
|
||||
[fan]
|
||||
pin: PH6
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
# Must limit Z velocity, since RAMPS does not have enough timer resolution
|
||||
max_z_velocity: 3
|
||||
max_z_accel: 100
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyUSB0
|
||||
|
||||
# Common EXP1 / EXP2 (display) pins
|
||||
[board_pins]
|
||||
aliases:
|
||||
# Common EXP1 header found on many "all-in-one" ramps clones
|
||||
EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
|
||||
EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
|
||||
# EXP2 header
|
||||
EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
|
||||
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
|
||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
||||
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
|
|
@ -29,6 +29,7 @@ CONFIG ../../config/printer-anycubic-4maxpro-2.0-2021.cfg
|
|||
CONFIG ../../config/printer-anycubic-i3-mega-2017.cfg
|
||||
CONFIG ../../config/printer-anycubic-kossel-2016.cfg
|
||||
CONFIG ../../config/printer-anycubic-kossel-plus-2017.cfg
|
||||
CONFIG ../../config/printer-bq-hephestos-2014.cfg
|
||||
CONFIG ../../config/printer-creality-cr10-v3-2020.cfg
|
||||
CONFIG ../../config/printer-creality-cr10s-2017.cfg
|
||||
CONFIG ../../config/printer-creality-cr20-2018.cfg
|
||||
|
|
Loading…
Reference in New Issue