From af1cd3c4ce36f43bdd9d45201b906d2c9e89a971 Mon Sep 17 00:00:00 2001
From: Arksine <arksine.code@gmail.com>
Date: Wed, 27 Jun 2018 11:59:02 -0400
Subject: [PATCH] config: add configuration for Creality Ender 2

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
---
 config/printer-creality-ender2-2017.cfg | 86 +++++++++++++++++++++++++
 1 file changed, 86 insertions(+)
 create mode 100644 config/printer-creality-ender2-2017.cfg

diff --git a/config/printer-creality-ender2-2017.cfg b/config/printer-creality-ender2-2017.cfg
new file mode 100644
index 00000000..e2845c3f
--- /dev/null
+++ b/config/printer-creality-ender2-2017.cfg
@@ -0,0 +1,86 @@
+# This file contains common pin mappings for the 2017 Creality
+# Ender 2. To use this config, the firmware should be compiled for the
+# AVR atmega1284p.
+
+# Note, a number of Melzi boards are shipped without a bootloader. In
+# that case, an external programmer will be needed to flash a
+# bootloader to the board (for example, see
+# http://www.instructables.com/id/Flashing-a-Bootloader-to-the-CR-10/
+# ). Once that is done, one should be able to use the standard "make
+# flash" command to flash Klipper.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PD7
+dir_pin: !PC5
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^PC2
+position_endstop: 0
+position_max: 165
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC6
+dir_pin: !PC7
+enable_pin: !PD6
+step_distance: .0125
+endstop_pin: ^PC3
+position_endstop: 0
+position_max: 165
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB3
+dir_pin: PB2
+enable_pin: !PA5
+step_distance: .0025
+endstop_pin: ^PC4
+position_endstop: 0.0
+position_max: 205
+
+[extruder]
+step_pin: PB1
+dir_pin: !PB0
+enable_pin: !PD6
+step_distance: 0.010753
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+max_extrude_only_distance: 500.0
+max_extrude_only_velocity: 200.0
+max_extrude_only_accel: 500.0
+heater_pin: PD5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA7
+control: pid
+pid_Kp: 21.73
+pid_Ki: 1.54
+pid_Kd: 76.55
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PD4
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA6
+control: pid
+# PID Tuned for 60C
+pid_Kp: 72.487
+pid_Ki: 2.279
+pid_Kd: 576.275
+min_temp: 0
+max_temp: 100
+
+[fan]
+pin: PB4
+
+[mcu]
+serial: /dev/ttyUSB0
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1500
+max_z_velocity: 5
+max_z_accel: 100