heater: Add PrinterHeaters class that stores all sensors and heaters

Add a PrinterHeaters class that can stores references to available
temperature sensors and stores references to instantiated heaters.

Add a extras/heater_bed.py file and delay instantiation of the
heater_bed object.  This allows the heater.py module to be imported
earlier during the setup phase, and allows the PrinterHeaters class to
be available for registering sensors and heaters.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

klippy/extras/heater_bed.py

@@ -0,0 +1,8 @@
+# Support for a heated bed
+#
+# Copyright (C) 2018  Kevin O'Connor <kevin@koconnor.net>
+#
+# This file may be distributed under the terms of the GNU GPLv3 license.
+
+def load_config(config):
+    return config.get_printer().lookup_object('heater').setup_heater(config)

klippy/extras/heater_fan.py

@@ -3,7 +3,7 @@
 # Copyright (C) 2016-2018  Kevin O'Connor <kevin@koconnor.net>
 #
 # This file may be distributed under the terms of the GNU GPLv3 license.
-import fan, extruder
+import fan
 
 PIN_MIN_TIME = 0.100
 
@@ -20,8 +20,8 @@ class PrinterHeaterFan:
         self.fan.mcu_fan.setup_start_value(0., max_power)
     def printer_state(self, state):
         if state == 'ready':
-            self.heater = extruder.get_printer_heater(
-                self.printer, self.heater_name)
+            pheater = self.printer.lookup_object('heater')
+            self.heater = pheater.lookup_heater(self.heater_name)
             reactor = self.printer.get_reactor()
             reactor.register_timer(self.callback, reactor.NOW)
     def callback(self, eventtime):

klippy/extras/pid_calibrate.py

@@ -4,7 +4,7 @@
 #
 # This file may be distributed under the terms of the GNU GPLv3 license.
 import math, logging
-import extruder, heater
+import heater
 
 class PIDCalibrate:
     def __init__(self, config):
@@ -18,8 +18,9 @@ class PIDCalibrate:
         heater_name = self.gcode.get_str('HEATER', params)
         target = self.gcode.get_float('TARGET', params)
         write_file = self.gcode.get_int('WRITE_FILE', params, 0)
+        pheater = self.printer.lookup_object('heater')
         try:
-            heater = extruder.get_printer_heater(self.printer, heater_name)
+            heater = pheater.lookup_heater(heater_name)
         except self.printer.config_error as e:
             raise self.gcode.error(str(e))
         print_time = self.printer.lookup_object('toolhead').get_last_move_time()

klippy/extras/verify_heater.py

@@ -4,7 +4,6 @@
 #
 # This file may be distributed under the terms of the GNU GPLv3 license.
 import logging
-import extruder
 
 HINT_THERMAL = """
 See the 'verify_heater' section in config/example-extras.cfg
@@ -29,8 +28,8 @@ class HeaterCheck:
         self.fault_systime = self.printer.get_reactor().NEVER
     def printer_state(self, state):
         if state == 'connect':
-            self.heater = extruder.get_printer_heater(
-                self.printer, self.heater_name)
+            pheater = self.printer.lookup_object('heater')
+            self.heater = pheater.lookup_heater(self.heater_name)
             logging.info("Starting heater checks for %s", self.heater_name)
             reactor = self.printer.get_reactor()
             reactor.register_timer(self.check_event, reactor.NOW)

klippy/extruder.py

@@ -4,7 +4,7 @@
 #
 # This file may be distributed under the terms of the GNU GPLv3 license.
 import math, logging
-import stepper, heater, homing
+import stepper, homing
 
 EXTRUDE_DIFF_IGNORE = 1.02
 
@@ -13,10 +13,11 @@ class PrinterExtruder:
         self.printer = printer
         self.name = config.get_name()
         shared_heater = config.get('shared_heater', None)
+        pheater = printer.lookup_object('heater')
         if shared_heater is None:
-            self.heater = heater.PrinterHeater(printer, config)
+            self.heater = pheater.setup_heater(config)
         else:
-            self.heater = get_printer_heater(printer, shared_heater)
+            self.heater = pheater.lookup_heater(shared_heater)
         self.stepper = stepper.PrinterStepper(printer, config)
         self.nozzle_diameter = config.getfloat('nozzle_diameter', above=0.)
         filament_diameter = config.getfloat(
@@ -274,12 +275,3 @@ def get_printer_extruders(printer):
             break
         out.append(extruder)
     return out
-
-def get_printer_heater(printer, name):
-    if name == 'heater_bed':
-        return printer.lookup_object(name)
-    if name == 'extruder':
-        name = 'extruder0'
-    if name.startswith('extruder'):
-        return printer.lookup_object(name).get_heater()
-    raise printer.config_error("Unknown heater '%s'" % (name,))

klippy/heater.py

@@ -104,13 +104,14 @@ PWM_DELAY = REPORT_TIME + SAMPLE_TIME*SAMPLE_COUNT
 class error(Exception):
     pass
 
-class PrinterHeater:
+class Heater:
     error = error
-    def __init__(self, printer, config):
-        self.printer = printer
+    def __init__(self, config):
+        printer = config.get_printer()
         self.name = config.get_name()
-        sensor_params = config.getchoice('sensor_type', Sensors)
-        self.sensor = sensor_params['class'](config, sensor_params)
+        sensor_type = config.get('sensor_type')
+        pheater = printer.lookup_object('heater')
+        self.sensor = pheater.setup_sensor(sensor_type, config)
         self.min_temp = config.getfloat('min_temp', minval=KELVIN_TO_CELCIUS)
         self.max_temp = config.getfloat('max_temp', above=self.min_temp)
         self.min_extrude_temp = config.getfloat(
@@ -278,7 +279,42 @@ class ControlPID:
         return (abs(temp_diff) > PID_SETTLE_DELTA
                 or abs(self.prev_temp_deriv) > PID_SETTLE_SLOPE)
 
+
+######################################################################
+# Sensor and heater lookup
+######################################################################
+
+class PrinterHeaters:
+    def __init__(self, printer, config):
+        self.printer = printer
+        self.sensors = {}
+        self.heaters = {}
+    def add_sensor(self, sensor_type, params):
+        self.sensors[sensor_type] = params
+    def setup_sensor(self, sensor_type, config):
+        if sensor_type not in self.sensors:
+            raise self.printer.config_error("Unknown temperature sensor '%s'" % (
+                sensor_type,))
+        params = self.sensors[sensor_type]
+        return params['class'](config, params)
+    def setup_heater(self, config):
+        heater_name = config.get_name()
+        if heater_name == 'extruder':
+            heater_name = 'extruder0'
+        if heater_name in self.heaters:
+            raise config.error("Heater %s already registered" % (heater_name,))
+        self.heaters[heater_name] = heater = Heater(config)
+        return heater
+    def lookup_heater(self, heater_name):
+        if heater_name == 'extruder':
+            heater_name = 'extruder0'
+        if heater_name not in self.heaters:
+            raise self.printer.config_error(
+                "Unknown heater '%s'" % (heater_name,))
+        return self.heaters[heater_name]
+
 def add_printer_objects(printer, config):
-    if config.has_section('heater_bed'):
-        printer.add_object('heater_bed', PrinterHeater(
-            printer, config.getsection('heater_bed')))
+    ph = PrinterHeaters(printer, config)
+    printer.add_object('heater', ph)
+    for sensor_type, params in Sensors.items():
+        ph.add_sensor(sensor_type, params)

klippy/klippy.py

@@ -7,7 +7,7 @@
 import sys, os, optparse, logging, time, threading
 import collections, ConfigParser, importlib
 import util, reactor, queuelogger, msgproto
-import gcode, pins, mcu, toolhead, extruder, heater
+import gcode, pins, heater, mcu, toolhead, extruder
 
 message_ready = "Printer is ready"
 
@@ -204,11 +204,11 @@ class Printer:
             ConfigLogger(fileconfig, self.bglogger)
         # Create printer components
         config = ConfigWrapper(self, fileconfig, 'printer')
-        for m in [pins, mcu]:
+        for m in [pins, heater, mcu]:
             m.add_printer_objects(self, config)
         for section in fileconfig.sections():
             self.try_load_module(config, section)
-        for m in [toolhead, extruder, heater]:
+        for m in [toolhead, extruder]:
             m.add_printer_objects(self, config)
         # Validate that there are no undefined parameters in the config file
         valid_sections = { s: 1 for s, o in self.all_config_options }