config: Add printer-anet-a4-2018.cfg config file
Reported by @Alkarasu. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
1d05a34cd7
commit
ab5540bd34
|
@ -0,0 +1,94 @@
|
|||
# This file contains common pin mappings for Anet A4 printer from
|
||||
# 2018. To use this config, the firmware should be compiled for the
|
||||
# AVR atmega1284p.
|
||||
|
||||
# Note that the "make flash" command does not work with Anet boards -
|
||||
# the boards are typically flashed with this command:
|
||||
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
||||
|
||||
# See the example.cfg file for a description of available parameters.
|
||||
|
||||
[stepper_a]
|
||||
step_pin: PD7
|
||||
dir_pin: !PC5
|
||||
enable_pin: !PD6
|
||||
step_distance: .01
|
||||
endstop_pin: ^!PC2
|
||||
position_endstop: 215
|
||||
arm_length: 215
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_b]
|
||||
step_pin: PC6
|
||||
dir_pin: !PC7
|
||||
enable_pin: !PD6
|
||||
step_distance: .01
|
||||
endstop_pin: ^!PC3
|
||||
|
||||
[stepper_c]
|
||||
step_pin: PB3
|
||||
dir_pin: !PB2
|
||||
enable_pin: !PA5
|
||||
step_distance: .01
|
||||
endstop_pin: ^!PC4
|
||||
homing_speed: 20
|
||||
|
||||
[extruder]
|
||||
step_pin: PB1
|
||||
dir_pin: PB0
|
||||
enable_pin: !PD6
|
||||
step_distance: .01045
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PD5
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PA7
|
||||
control: pid
|
||||
pid_Kp: 30.48
|
||||
pid_Ki: 2.71
|
||||
pid_Kd: 85.52
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PD4
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: PA6
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PB4
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyUSB0
|
||||
|
||||
[printer]
|
||||
kinematics: delta
|
||||
max_velocity: 300
|
||||
max_accel: 1000
|
||||
max_z_velocity: 20
|
||||
delta_radius: 113
|
||||
|
||||
[delta_calibrate]
|
||||
radius: 70
|
||||
|
||||
[display]
|
||||
lcd_type: hd44780
|
||||
rs_pin: PA3
|
||||
e_pin: PA2
|
||||
d4_pin: PD2
|
||||
d5_pin: PD3
|
||||
d6_pin: PC0
|
||||
d7_pin: PC1
|
||||
up_pin: PA1
|
||||
analog_range_up_pin: 9000, 13000
|
||||
down_pin: PA1
|
||||
analog_range_down_pin: 800, 1300
|
||||
click_pin: PA1
|
||||
analog_range_click_pin: 2000, 2500
|
||||
back_pin: PA1
|
||||
analog_range_back_pin: 4500, 5000
|
||||
#kill_pin: PA1
|
||||
#analog_range_kill_pin: 400, 600
|
|
@ -46,6 +46,7 @@ CONFIG ../../config/generic-minitronics1.cfg
|
|||
# Printers using the atmega1284p
|
||||
DICTIONARY atmega1284p.dict
|
||||
CONFIG ../../config/generic-melzi.cfg
|
||||
CONFIG ../../config/printer-anet-a4-2018.cfg
|
||||
CONFIG ../../config/printer-anet-a8-2017.cfg
|
||||
CONFIG ../../config/printer-anet-e10-2018.cfg
|
||||
CONFIG ../../config/printer-creality-cr10-2017.cfg
|
||||
|
|
Loading…
Reference in New Issue