config: Add printer-anet-a4-2018.cfg config file
Reported by @Alkarasu. Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
parent
1d05a34cd7
commit
ab5540bd34
|
@ -0,0 +1,94 @@
|
||||||
|
# This file contains common pin mappings for Anet A4 printer from
|
||||||
|
# 2018. To use this config, the firmware should be compiled for the
|
||||||
|
# AVR atmega1284p.
|
||||||
|
|
||||||
|
# Note that the "make flash" command does not work with Anet boards -
|
||||||
|
# the boards are typically flashed with this command:
|
||||||
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
||||||
|
|
||||||
|
# See the example.cfg file for a description of available parameters.
|
||||||
|
|
||||||
|
[stepper_a]
|
||||||
|
step_pin: PD7
|
||||||
|
dir_pin: !PC5
|
||||||
|
enable_pin: !PD6
|
||||||
|
step_distance: .01
|
||||||
|
endstop_pin: ^!PC2
|
||||||
|
position_endstop: 215
|
||||||
|
arm_length: 215
|
||||||
|
homing_speed: 50
|
||||||
|
|
||||||
|
[stepper_b]
|
||||||
|
step_pin: PC6
|
||||||
|
dir_pin: !PC7
|
||||||
|
enable_pin: !PD6
|
||||||
|
step_distance: .01
|
||||||
|
endstop_pin: ^!PC3
|
||||||
|
|
||||||
|
[stepper_c]
|
||||||
|
step_pin: PB3
|
||||||
|
dir_pin: !PB2
|
||||||
|
enable_pin: !PA5
|
||||||
|
step_distance: .01
|
||||||
|
endstop_pin: ^!PC4
|
||||||
|
homing_speed: 20
|
||||||
|
|
||||||
|
[extruder]
|
||||||
|
step_pin: PB1
|
||||||
|
dir_pin: PB0
|
||||||
|
enable_pin: !PD6
|
||||||
|
step_distance: .01045
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.750
|
||||||
|
heater_pin: PD5
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PA7
|
||||||
|
control: pid
|
||||||
|
pid_Kp: 30.48
|
||||||
|
pid_Ki: 2.71
|
||||||
|
pid_Kd: 85.52
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 250
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: PD4
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PA6
|
||||||
|
control: watermark
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 130
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
pin: PB4
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
serial: /dev/ttyUSB0
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: delta
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 1000
|
||||||
|
max_z_velocity: 20
|
||||||
|
delta_radius: 113
|
||||||
|
|
||||||
|
[delta_calibrate]
|
||||||
|
radius: 70
|
||||||
|
|
||||||
|
[display]
|
||||||
|
lcd_type: hd44780
|
||||||
|
rs_pin: PA3
|
||||||
|
e_pin: PA2
|
||||||
|
d4_pin: PD2
|
||||||
|
d5_pin: PD3
|
||||||
|
d6_pin: PC0
|
||||||
|
d7_pin: PC1
|
||||||
|
up_pin: PA1
|
||||||
|
analog_range_up_pin: 9000, 13000
|
||||||
|
down_pin: PA1
|
||||||
|
analog_range_down_pin: 800, 1300
|
||||||
|
click_pin: PA1
|
||||||
|
analog_range_click_pin: 2000, 2500
|
||||||
|
back_pin: PA1
|
||||||
|
analog_range_back_pin: 4500, 5000
|
||||||
|
#kill_pin: PA1
|
||||||
|
#analog_range_kill_pin: 400, 600
|
|
@ -46,6 +46,7 @@ CONFIG ../../config/generic-minitronics1.cfg
|
||||||
# Printers using the atmega1284p
|
# Printers using the atmega1284p
|
||||||
DICTIONARY atmega1284p.dict
|
DICTIONARY atmega1284p.dict
|
||||||
CONFIG ../../config/generic-melzi.cfg
|
CONFIG ../../config/generic-melzi.cfg
|
||||||
|
CONFIG ../../config/printer-anet-a4-2018.cfg
|
||||||
CONFIG ../../config/printer-anet-a8-2017.cfg
|
CONFIG ../../config/printer-anet-a8-2017.cfg
|
||||||
CONFIG ../../config/printer-anet-e10-2018.cfg
|
CONFIG ../../config/printer-anet-e10-2018.cfg
|
||||||
CONFIG ../../config/printer-creality-cr10-2017.cfg
|
CONFIG ../../config/printer-creality-cr10-2017.cfg
|
||||||
|
|
Loading…
Reference in New Issue